Many shielded cables come in various materials and designs, so having one with a copper mesh covering the inner insulator wire is no problem. We currently use a extension cord found locally at a hardware store and include one 18G wire for ground. So a specific shielded cable is not a required, unless being used next to specific and sensitive electronics that are extremely sensitive to noise and voltage interference than a shielded cable is required.

Click the link to add information to this solution:
I purchased a 2.2 spindle a while back and went to the electrical supply house to but shielded cable for the power run, I was on the web a while back and saw a picture of shielded cable that didn't look like what I had bought. should it have a copper like mesh wraped around the inner insulation. Thanks

I would highly recommend a spindle and VFD rather than a router.

Spindles:
- Have a far longer life longer than a router. You will probably go through a few routers before the end of the spindle's life.
- Are quieter than routers
- And the water cooled spindles we stock do not blow the chips into the air. Chips are much easier to capture with or without a dust removal system.

You can find our spindles here:
https://www.buildyourcnc.com/SpindlesAndAccessories.aspx

Once you get your first spindle, you will never go back to routers. Routers are great for handrouting work, but not the best for continuous CNC milling.

Click the link to add information to this solution:
Hi there, I have a cnc table that I built but I am looking for a higher powered router because I am using the table for flattening slabs with a large straight bit. Would you have any recommendations for the type of router I should buy? Also do you sell large bits for flattening slabs?

Depending on the type of motors and connection type, you could adapt your motors to work with our electronic packages, but you will receive additional motors since our kit is complete.

Now you will have to take into affect the actual motors you have and compare or get accurate replacements(Ex. our 425 oz motor(1/4" input shaft) will have to be same size or similar entry holes)

Your Controller board will be the major issue, due to its wiring and processing manner, you can view the connections for our breakout boards to compare with yours! (parallel: https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/)(USB: https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/)
Email(customerservice@buildyourcnc.com for further help)

Click the link to add information to this solution:
I am looking at one of your electronics packages as a replacement for my excisting electronics. I have a old table top CNC that has a bad electronics pack, but the motors, and the mill are in good shape. could your system be adapted to work in this case?

We can special order this part for you. Give us a call and we will either find the part for you, or find a part that we can machine to your specifications.

Click the link to add information to this solution:
HI, I am looking for a drive sproket for a roller chain. The drive sproket should have an ID= 16mm. do you have something like this in your inventory?

All of our controller will allow two steppers on any of the axes. Multiple stepper motors and drivers on a single axis is more a function of the way the stepper motor drives are connected to the output pins of the controller. To connect two stepper drivers to a single axis, you need to connect the output pins (dir and step) to each of the two stepper motor drivers.

Consider the controller on cost, features and how they are connected to the computer.

Out lowest cost controllers are:

Mach3 USB board - Has good features and uses the USB from the computer as the main connection
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Parallel Breakout - The computer generates the main signals and this board conditions the signals for the drivers. Although it requires the parallel port from older computer, the board has the most broad compatibility with control software out there including Mach3 and LinuxCNC.
https://buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Highest cost but most feature rich:

Pokey57CNC - works with both Mach3 and Mach4
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
I am looking for a controller for a 3 axis dual Y stepper cnc machine. If at all possible I would like a list of the parts that will be needed. I prefer to go with an ethernet setup vs a parallel port.

Yes, servo motors can be mounted on this machine. If the mounting dimensions are different than NEMA 23 or NEMA 34, then all you need to do is keep the center of the motorshaft with the center of the bearing location and locate the mounting holes for he servo you wish to use. Most industrial servos used for these machines share the same mounting dimensions and NEMA specifications.

Additional Information:
This machine is one of the most customizable machines out in the wild. Customers of these machines have fashioned many modifications to suit their needs.

Additional Information:
20

Click the link to add information to this solution:
[796] Hello. To what extent can the design plans be customized? For example, if I wanted servo motors instead of steppers? That would requirements for motor mounting, controls, and electrical. Thank you.

You can do raster and vector engraving on the greenBull laser/spindle combination. The methods of this process is not accomplished in the same way as the typical laser machines where CorelDRAW is used. The Mach3 laser plug-in can be used for the raster engraving and standard CNC g-code can be used for vector cutting and engraving.

The raster method will not be fast on the greenBull since the z-axis is heavy and there are inertial limitation on doing fast raster back and forth movement. Vector is the best use of this machine.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I am looking at purchasing the greenbull 5X system with the laser/spindle combination. Can the laser do both rastered engraving as well as vectored cutting with the same breakout board and software? If I have this wrong please let me know what would be needed to accompish this.

I just posted the "enhanced" Blacktooth wiring diagram I developed. Check it out here.

http://www.buildyourtools.com/phpBB3/viewtopic.php?f=12&t=4872

Click the link to add information to this solution:
Where do I wire the ground of my "th" and "power 0v - 5v" command on the power supply ? Is it possible to have a detailed blueprint of the electrical wiring (not for the blacktooth but in general) ? Many thanks :)

A wireless MPG is generally independent of the controller since it communicates to Mach3 directly and does not pass through the controller. I am using a wireless MPG and I have no problems with either of the controllers that I sell (Mach3 USB controller or the Pokeys57CNC controller).

The issue you are having may be in the configuration of the wireless MPG that you are using.

Click the link to add information to this solution:
I am trying to decide which board I should use. I have a wireless MPG and every time I jog Z my X axis steps. If this is not a board issue I would like to go with a wired MPG. So I would like a board that I can have a wired MPG, use a tool touch off probe, control either spindle (VFD) on/off or on/off with speed control, and have homing switches.

We may be able to source those motors. Curious, the 6000 oz-in motor is pretty big. Do you mind explaining the application of the CNC machine and the structure that would require the large motor?

Additional Information:
The largest motors we can offer is 3900 oz-in without any mechanical help. 6000 oz-in can be resolved by mechanical means as an alternative.

Click the link to add information to this solution:
I am converting a 12x36 lathe over to CNC, I am interested in a 2 axis kit. I would love one stepper motor to be no smaller than 1200oz. , and another at 6000z. Is this something that you could offer? I have two other cnc machines but this is my first converstion on my own.

Please contact us at sales@buildyourcnc.com so we can provide you with assistance on your order

Click the link to add information to this solution:
I am trying to purchase a kit for our school in Singapore, and your site keeps refusing our corporate AMEX card. Can you help us figure out what is up with that? Are you not ship to Singapore or something? Our AMEX rep says that the account is authorised for this purchase from our end, so the problem may be with your site? Please advise.

BYCNC Response:
This is correct. You will need to use a method appropriate for the software you are using. Also remember that NC switches are typically wired in series, while NO switches are normally wired in parallel.

User Response:
I am using the cnc planet software for your USB board. Are the limit configurations in this software?

BYCNC Response:
Yes, Planet CNC software is compatible with the use of limit switches. Configuration information will depend on your specific application. You can view Planet CNC's information here: http://www.planet-cnc.com/files/CNCUSBController.pdf

Click the link to add information to this solution:
LIMIT SWITCHES FOR AXIS. THE PRINT SHOWS THAT YOU CAN WIRE LIMITS EITHER N.O. OR N.C. SO IF THIS IS CORRECT I WOULD NEED TO TELL BOARD IN SOFTWARE HOW LOOK AT THESE LIMITS, I'M GOING GET AN INPUT LOOSE DEPEND ON IT.

Yes, you can find all of the instructions for the blackToe CNC Router here:
https://buildyourcnc.com/item/cnc-machine-blacktoe-v4-2x4

Click the link to add information to this solution:
I recently purchase the BlackToe v2.1 (4x8) at a local school auction. The table is complete, however, it is missing the spindle and came in 4 (four) separate pieces. Are there plans for this machine that I would be able to use to reconstruct and determine if anything else is missing.

CamBam specifically creates the g-code (machining operations) instructions to be loaded into Mach3. Make sure in your CamBam g-code file parameters, you are using the Mach3 post processor. If you have already done this, let me know. If you are not sure how to do this, let me know.

Click the link to add information to this solution:
I am having trouble connecting the cambam program with my Mach3 to my 4X8 Blackfoot CNC machine. Where can I get help on this issue. Have had my machine since 2015 and have not been able to use it. Thank you

Usually this does happen, we tend to clean the water out roughly every month, however we use our machine 8hrs a day, 7 days a week non stop. So Depending on your usage it might be every 3-5 months when you might have to change the water.

We use a small air compressor to blow the build up through the spindle.

Click the link to add information to this solution:
I have the same water for months to cool the spindel and it's blocked, what can I use to unblock it? I would not like to damage any seal or gasket inside.

Identify the Control Signals: First, determine which control signals from the DB25 interface card are used for spindle speed control. Typically, these are PWM (Pulse Width Modulation) signals or analog voltage signals.

VFD Configuration: Your VFD should be configured to accept the type of control signal your DB25 card provides. This involves setting parameters in the VFD that correspond to the type of input signal it will receive for speed control.

Wiring: Connect the appropriate output pins from the DB25 card to the input terminals on the VFD. This usually involves connecting the PWM or analog output to the corresponding input on the VFD. Make sure to consult the manuals for both your VFD and interface card for specific wiring details.

UCCNC Settings: Configure UCCNC to output the correct type of signal (PWM or analog) that matches your VFD's configuration. This is done through the software's spindle setup section.

Test and Adjust: Run some tests to ensure that the spindle speed is being correctly controlled by UCCNC. You might need to tweak settings in either the VFD or UCCNC for optimal performance.

Click the link to add information to this solution:
I am looking at purchasing your 2.2 kw water cooled spindle. I'm assuming it comes with the VFD. I have a rotary phase converter in my shop. Are these spindles 3 phase? And if so, can I bypass use of the VFD and control the spindle speed by the CAM software instead? Or is the VFD an absolute necessity to use on the spindle?

The blackFoot uses the same electronics and motors as the blackToe (2'x4') machine. The only parts that change are the gantry horizontal structural parts which may be relatively easy for you to change. We can send you those parts if you are interested in a smaller unit.

Click the link to add information to this solution:
I have a Blackfoot that was purchased in 2017, after the purchase we moved and I haven’t been able to find room for it... would you be interested in buying it back or trading for something smaller. The Blackfoot and computer have never run but I did purchase it assembled. Thanks in advance, scott

If you have received a part that does not work as advertised, or does not function properly, we will ship you a replacement. Please contact customerservice@buildyourcnc.com to make these arrangements.

Click the link to add information to this solution:
I would like to re-order another breakout board, but I would like each output tested beofore shipping. I have recieved a breakout board where the mist coolant doesnt work, and the y-axis sends a 1.5vdc signal voltage. They should all be 5v as you know, or the driver will not read.

We apologize for the confusion, however in the very first video that is regarding the assembly, is of the torsion box. We do not included that in any greenBull kit, as we use too sell it individually! However due to high consumption of materials and high cost(both in shipping and for the kit itself) we have removed it from our inventory and no longer sell it.

This video can be skipped, however if you plan on making a DIY torsion box, this video will be helpful in your build!

The torsion box is not needed, as the frame itself will be more than sufficient in keeping the machine from flexing or vibrating.

Click the link to add information to this solution:
I ordered the GreenBull 5' x 10' kit. The first video for assembly shows that I should have 5 large boards that attach to the table, but I don't have those boards. Is that something I need to build or were they not shipped?