You can find the datasheets to our motors be going to the the stepping motor category page https://www.buildyourcnc.com/category/nema and selecting the motor. This will bring you to the product page for the motor and all of the motor information will be found there.

Click the link to add information to this solution:
I would like to design my own CNC router around one of your electronics bundles, either the 3 Axis - Heavy Gantry or 3 Axis - All Large Motors. Do you have the data sheets for the motors so that I can use the dimensions in my model?

Yes, we can provide a laser attachment for the long Z version of the greenBull 4x, 5x and 6x. Please call us to get more information and pricing for the laser attachment.

Click the link to add information to this solution:
I have a greenbull 5x with the long Z. Is there a laser kit that I can get for that model?

Yes, you can use Mach4 wtih the Fabricator Pro CNC machine.

We have not designed a metal machine like the Fabricator Pro to lean more in the vertical orientation. Unfortunately, we haven't gotten any requests for that style of machine, and the greenLean, although a great machine and space saver, has not been our best seller.

If we get more interest in this type of machine, we would have no problem designing a machine like this.

Click the link to add information to this solution:
Do you have a model of the Fabricator pro that can be inclined line the lean? I have seen a few other machines on the market like this. Can we use Mach4 with the fabricator pro

Actual table dimension: 4'x8' is 56.078"x 121.50" (the overhang in the illustrations should be 3/4" thick)
To determine the frame dimensions, first consider using the frame height shown of almost 3' (2.86'). The width of the frame should be 4" narrower than the dimension from rail edge to rail edge (6X rail to rail is 80.078"). This will provide a 2" overhang on both sides (4X frame width should be 56.078").
The length of the frame should be 4" shorter than the desired length of the rails to provide a 2" overhang on both ends. The travel length will be 20" shorter than the rail length due to the space occupied by the gantry sides.
Two long pieces of 3/4" material will need to be placed on top of the frame with the 2" overhang on the sides and the end. These long strips of material will receive the rails and the chain mounts on the ends.


Link:
https://www.buildyourcnc.com/Item/cnc-machine-greenBull-v4-4X

Click the link to add information to this solution:
What are the table dimensions for the greenBull so I can build it.

I would recommend creating a post in our forums page (buildyourtools.com), and ask any specific questions there! Since there might be someone willing to help you locally!

Since we cannot disclose any customers contact information, without there permission! Going through the forums will be the best idea to be able to find someone locally, with one of our machines!

Also you can contact us directly at customerservice@buildyourcnc.com

Click the link to add information to this solution:
Do you have customers/builders in the Netherlands who I can ask for help or assistance?

Actual table dimension: 4'x8' is 56.078"x 121.50" (the overhang in the illustrations should be 3/4" thick)
To determine the frame dimensions, first consider using the frame height shown of almost 3' (2.86'). The width of the frame should be 4" narrower than the dimension from rail edge to rail edge (6X rail to rail is 80.078"). This will provide a 2" overhang on both sides (4X frame width should be 56.078").
The length of the frame should be 4" shorter than the desired length of the rails to provide a 2" overhang on both ends. The travel length will be 20" shorter than the rail length due to the space occupied by the gantry sides.
Two long pieces of 3/4" material will need to be placed on top of the frame with the 2" overhang on the sides and the end. These long strips of material will receive the rails and the chain mounts on the ends.


Link:
https://www.buildyourcnc.com/Item/cnc-machine-greenBull-v4-4X

Click the link to add information to this solution:
I have just purchased a 4x8 Greenbull system second-hand. Are there any schematics for table dimensions and rail-mounting available so that I can build a table? (previous owner disassembled)

Are you trying to use the MPG (tab), or the keyboard for jogging the motors? You mention 0,0,0, are you trying to home the machine with the "ref all home"?

If you cannot move the motors with the keyboard, check if the jog is enabled.

Click the link to add information to this solution:
[596] I have my motors and limit switches working correctly but I am unable to get any movement from the 'jog step' so that I can set 0,0,0. What should I check

The plans for the whiteAnt 3D Printer will have the dimesions, and the dimensions will be on the individual pieces(cut to spec). The machine is relatively small, so maybe you expected the size(dimensions) to be larger.

Click the link to add information to this solution:
The plans available for download for the "whiteAnt 3D Plastic Printer" do not have dimensions. Are the dimensions shown in the book? Is there a DWG file available?

Yes, absolutely. If you need two motors for a single axis, you will want to use the same terminals for pulse and direction from the breakout board.

More specifically, you will wire the step/pulse pin to both drivers, and the direction pin to both drivers. If the motors need to turn in different directions, simply swap the A and B coil connections on one of the motors.

Additional Information:
i have checked the cnc machine for any flex and there is none but i still cannot cut circles they end up square.have checked calibration and it is correct but if i run at 4000 mm feed all comes out correct but if i change feed to say 2000 mm it makes the part small, like in tiny.

Click the link to add information to this solution:
I'm going to use 2 stepper motors for my X-axis. Can I use the same connections on the B/O board to do this knowing I will need 2 separate driver boards.

If you are looking for the drivers to pair with NEMA 34 stepper motors, you can find the 6.0 amp drivers here:
https://www.buildyourcnc.com/item/electronicsAndMotors-stepper-driver-6!0a

The other electronics to send the signals to the 6.0 amp drivers (the control board that operates with the control software) is subject to personal preference, but here they are listed:

Our breakout board (works with Mach3 and LinuxCNC and requires a parallel port on your computer):
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

The PoKeys57CNC (works with Mach3 and Mach4):
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Generic USB breakout board (works with Mach3):
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Additional Information:
Do I need a driver for every motor or can I use one driver for all four motors

Additional Information:
Each motor needs its own driver.

Click the link to add information to this solution:
I HAVE NEMA 34 MOTORS BUT NEED THE ELECTRICAL COMPONENTS DO YOU A KIT WITHOUT INCLUDED?

Dealing with the dimensions of our scratch build kit, you can find the design and dimensions here (https://www.buildyourcnc.com/Documents/CNC%20Kit%201-1.pdf).
You can go to the main CNC book page here (https://www.buildyourcnc.com/Book.aspx).

Click the link to add information to this solution:
I am looking for the dimensions for drilling from the plans in the book

Are you looking for replacement motors?

Click the link to add information to this solution:
I have a 4' X 8' table with carriages that use nema 23 motors. I have a hypertherm 45 plasma cutter. I have 20 degree 20 pitch rack gear. Can you suggest a plug and run system that I can use for cnc plasma and cnc routing?

Ok, sure. Let's get the discussion started. Please respond with your questions on this FAQ

Click the link to add information to this solution:
Hi, I am thinking of making a CNC router that I can use in woodworking. I am very happy if you can help me with the necessary parts for this

Yes, the RNRMotion.dll file must be used and put in the plugins folder under the Mach3 folder.

The XML file that I link on the Mach3 USB controller page is the file you should start with. This file will have the necessary configuration that links the Mach3 USB controller to the Mach3 control software. You can then make whatever changes you need to this configuration to tailor it to your machine.

Do you see a quick flashing red led on the board when you press the arrow keys?

Additional Information:

Click the link to add information to this solution:
[575] Do I have to use the motion driver and configuration file to use this card? The x,y,a shows that it's moving on display, but the motors aren't moving.

Absolutely, I can answer this type of question and anything other questions you may have with your new-to-you CNC router.

Additional Information:
20

Click the link to add information to this solution:
[789] Can you help me with selecting a power supply ( and a few other components ) for the stepper motors that came with a homemade CNC Router I just purchased.

Dealing with running our CNC machines with roller chain on the X/Y-axes and lead screw on the Z-axis, we chose this method due to functionality and cost effectiveness. We wanted to make the lowest cost CNC machine available for our customers without taking to much functionality and precision away from the machine. We wanted the accuracy and cost effectiveness to be surprisingly high, with our machines getting thousandths of an inch will be no issue, and having it at a decent price!

Click the link to add information to this solution:
Hey. I have noticed that you guys use roller chain to move x,y axis and a lead screw to move the z axis, can you please explain the motivation in short? Thank you.

If you are looking for the drivers to pair with NEMA 34 stepper motors, you can find the 6.0 amp drivers here:
https://www.buildyourcnc.com/item/electronicsAndMotors-stepper-driver-6!0a

The other electronics to send the signals to the 6.0 amp drivers (the control board that operates with the control software) is subject to personal preference, but here they are listed:

Our breakout board (works with Mach3 and LinuxCNC and requires a parallel port on your computer):
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

The PoKeys57CNC (works with Mach3 and Mach4):
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Generic USB breakout board (works with Mach3):
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Additional Information:
Do I need a driver for every motor or can I use one driver for all four motors

Additional Information:
Each motor needs its own driver.

Click the link to add information to this solution:
I have Nema 34 motors but I need the electrical components do you have a kit without motors included?

Yes, you can use the 4 axis kit and use two of the motors on the gantry. You will need to wire the gantry axis motors to the same step and direction signals on the controller interface. For example, if the gantry axis is the X axis, then on the controller step and direction terminals (CP and CW) is wired to both of the stepper motor drivers for the X axis.

Click the link to add information to this solution:
4 axis kit can I use 2 motors for the gantry with one controller card? or I buy the 3 axis kit instead?

The specifications for our 3/8" bearings are R6ZZ. The ZZ means double metal shielded. The metal shielding is to protect the ball bearings between the inner race and outer race.

Inside diameter: 3/8"
Outside Diameter: 7/8"
Width: 9/32"

Click the link to add information to this solution:
what are the dimensions and model number of the 3/8" ID roller bearings on your website?