If you are looking for the drivers to pair with NEMA 34 stepper motors, you can find the 6.0 amp drivers here:
https://www.buildyourcnc.com/item/electronicsAndMotors-stepper-driver-6!0a

The other electronics to send the signals to the 6.0 amp drivers (the control board that operates with the control software) is subject to personal preference, but here they are listed:

Our breakout board (works with Mach3 and LinuxCNC and requires a parallel port on your computer):
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

The PoKeys57CNC (works with Mach3 and Mach4):
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Generic USB breakout board (works with Mach3):
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Additional Information:
Do I need a driver for every motor or can I use one driver for all four motors

Additional Information:
Each motor needs its own driver.

Click the link to add information to this solution:
I have Nema 34 motors but I need the electrical components do you have a kit without motors included?

We recommend checking the dip switch settings on your drivers, having the correct microstepping/amp settings along with the steps/unit will help the motors run as effective as possible.
This is a default parameter that we use while we test our motors:
Driver dip switch settings will be at a 1/16 microstepping and 2.7amp (11001100) for x/y-axis and the z-axis will be at 1/4 microstepping and 2.7amp (10101100).

In planet-cnc with increasing the motor speed, you will have to modify the settings in planet-cnc (File/settings/setup) you will modify the initial speed, maximum speed, and the acceleration.
X/Y-axis step/unit: 1422.22 initial speed:500 maximum speed:750 acceleration:25
Z-axis step/unit: 1600 initial speed:100 maximum speed:300 acceleration:25
The initial speed and maximum speed will have to be roughly tested and adjusted per application.
Make sure to adjust the JOG slide bard underneath the axis controls on screen to about 750, to compensate for your x/y-axis adjustments. If left alone the speed will max out at the default setting.

Here is a video tutorial to calculate the steps required depending on your mechanical linear motion components. (

Click the link to add information to this solution:
I bought Nema 24 motors and driver package with usb board. What do i need to have more speed? Cant even jog past 25 ipm without the motor stalling (not having enough torgue)

Yes, the redLeaf is integrated into the redLeaf, all wired and configured. It is a plug and play system.

Click the link to add information to this solution:
replacing all electronic on a small cnc would like to use the redleaf hd +4 nema 34 motors does mach 3 included already installed

If your motors are hot to the touch, this is normal. Current is being drawn by the motor coils as the motor moves and as the motor stays at a position. If the motor is not using the current in the coils to move (holding it's position), the energy will be translated as heat (rather than motion, sound or light). Even while moving, some of the energy will be lost as heat. Remember that energy cannot be created nor destroyed.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I HAVE FOLLOWED ALL THE "CNC ELECTRONICS 1 - 9" VIDEOS AND I'M USING ALMOST EXACT SAME COMPONENTS (MOTORS RUN SOUND GOOD) BUT MOTORS ARE RUNING VERY HOT IN JUST 15MIN WITH NO LOAD DONE SOMETHING WRONG OR DO STEPPERS HOT?

We have one in the works. It is a 4'x8' machine that will house the 80w laser tube on the gantry. The machine is bout 2 months out as of 1/7/2014.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Do you have a larger kit for the Blacktooth Laser? I need a laser with at least 80watts of power.

Yes, we can provide a pre-wired electronics listed on this page:

https://www.buildyourcnc.com/AssembledElectronics.aspx

If you require these without the motors, please give us a call so your motors can be wired correctly and you can purchase the system without the motors.

Currently, the office is closed due to flooding in the area, but we plan to re-open very shortly.

Click the link to add information to this solution:
Hi there. I am looking upgrading the electronics on my 8x4 machine. Do you do your pre wired kits without the motors?

To replace all of the electronics for a 4 axis system with all NEMA 34 motors, you will need the following components:

4 NEMA 34 stepper motors:
https://buildyourcnc.com/item/electronicsAndMotors-nema34-651ozin

4 drivers (one driver for each motor):
https://buildyourcnc.com/item/electronicsAndMotors-stepper-driver-6!0a

One controller:
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

24v Powers supply for the controller:
https://buildyourcnc.com/item/electronicsAndMotors-power-supply-24v-1a-dc

2 48V power supplies for the motors and drivers:
https://buildyourcnc.com/item/electronicsAndMotors-power-supply-24v-36v-48v

Click the link to add information to this solution:
what do i need to buy for a complete replacement 4 axis cnc mill nema 34 motors mach 3

Absolutely, I can answer this type of question and anything other questions you may have with your new-to-you CNC router.

Additional Information:
20

Click the link to add information to this solution:
[789] Can you help me with selecting a power supply ( and a few other components ) for the stepper motors that came with a homemade CNC Router I just purchased.

We do offer all of the parts; but it is best to purchase them a la carte. You will probably not want the hardware since this would not conform to a design in metal.

All of the mechanical parts are available here:
https://buildyourcnc.com/CNCMachineMechanicalParts.aspx

All of the electronics you would need is available here:
https://buildyourcnc.com/electronicscombo.aspx

All of the laser components are available here:
https://buildyourcnc.com/LaserComponents.aspx

And the spindles and VFDs are available here:
https://buildyourcnc.com/SpindlesAndAccessories.aspx

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Is it possible to order the mechanics, motors and electronics, in other words, order the kit without the wood? Reason being is I have aluminum and steel to make a machine out of.

If you are wanting to purchase all of the parts for a machine excluding the structural parts, you will need to order the parts a la carte.

Electronics packages can be found here:
https://buildyourcnc.com/category/elcombo

Mechanical components can be found here:
https://buildyourcnc.com/CNCMachineMechanicalParts.aspx

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Is it possible to order the mechanics, motors and electronics, in other words, order the kit without the wood? Reason being is I have aluminum and steel to make a machine out of.

If your motors are hot to the touch, this is normal. Current is being drawn by the motor coils as the motor moves and as the motor stays at a position. If the motor is not using the current in the coils to move (holding it's position), the energy will be translated as heat (rather than motion, sound or light). Even while moving, some of the energy will be lost as heat. Remember that energy cannot be created nor destroyed.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I have followed all the "CNC Electronics 1 - 9" videos and I'm using almost the exact same components (motors run and sound good) but the motors are runing very hot in just 15min with no load - have I done something wrong or do steppers run very hot?

You can find the datasheets to our motors be going to the the stepping motor category page https://www.buildyourcnc.com/category/nema and selecting the motor. This will bring you to the product page for the motor and all of the motor information will be found there.

Click the link to add information to this solution:
Do you have the data sheets for the motors so that I can use the dimensions in my model?

We currently do not have that application implemented in our design. please suggest this in our R/D section (http://buildyourcnc.com/ResDev.aspx).

Click the link to add information to this solution:
I need a customised blackfoot without spindle but mount for vacuum pump pick and place.What software do I need and what's the quote

Yes, I can furnish the redFly system without motors. You can request a quote for this at customerservice@buildlyourcnc.com

Click the link to add information to this solution:
[422] I'm interested in using Mach4 and already have 3 motors (425 oz-in). Is it possible to get a electronics system without the motors?

Yes, we honor a one year warranty on the NEMA 34 651 oz-in stepper motor.

Click the link to add information to this solution:
Is there a warranty on the NEMA 34 651 Oz-in stepper motors you sell?

Have you considered reversing the A and B coils on one of the motors to the drivers? This will cause the motor to spin in the opposite direction. This is the easiest method. Using the HEX inverter is a more complex method and not recommended for simple driving tasks.

Click the link to add information to this solution:
I have two nema 34 motors on my gantry and ordered a hex inverter, now I need to wire it correctly. What type of wiring hardware do I need and I will need a wiring diagram also. Please help.

Have you considered reversing the A and B coils on one of the motors to the drivers? This will cause the motor to spin in the opposite direction. This is the easiest method. Using the HEX inverter is a more complex method and not recommended for simple driving tasks.

Click the link to add information to this solution:
I have two nema 34 motors on my gantry and ordered a hex inverter, now I need to wire it correctly. What type of wiring hardware do I need and I will need a wiring diagram also. Please help.

No, you do not need another motion controller if you have the parallel breakout board and you are using the "Legacy Parallel Port Plug-In" with Mach4. The motion controller is the parallel port.

Click the link to add information to this solution:
I purchased hardware for my plasma table which included 3 nema 34 stepper motors and drivers, power supply,Blue brew BOB, and Mach 4 Control software with parallel port plug-in. In configuring the Mach 4 software it asks for a motion controler. Do I need another device such as a smoothstepper motion controler?

We will make sure that order is changed prior to shipping.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
just placed an order for 2 nema 34 and 1 24 stepper motors i meant to have be 1, 34 and 2, 24 stepper motors. I need to change that before shipping