If your motors are hot to the touch, this is normal. Current is being drawn by the motor coils as the motor moves and as the motor stays at a position. If the motor is not using the current in the coils to move (holding it's position), the energy will be translated as heat (rather than motion, sound or light). Even while moving, some of the energy will be lost as heat. Remember that energy cannot be created nor destroyed.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I have followed all the "CNC Electronics 1 - 9" videos and I'm using almost the exact same components (motors run and sound good) but the motors are runing very hot in just 15min with no load - have I done something wrong or do steppers run very hot?

The files and hardware option for our machines has been removed from the site due to the following reasons:
Difficulty for the end use of the files and the challenges (and time/money) on our side to assist in using these files.
The abuse of these files over the internet.
Ultimately may reduce the sales of machines keeping us in business.
Sadly, this is what has come out of our company attempting to be open; however, the machines sold on this site is still far lower in price than the competition for the quality that we provide as we have a great desire to engender the cottage industry to fulfill their need for low end manufacturing. My sincere apologies if this causes any inconvenience.

Additional Information:
NO, is not possible, I can help with the shipping cost

Additional Information:

Click the link to add information to this solution:
Is it possible to buy just the electronics and hardware for the bigfoot along with the plans for the timber components so that I could have them cut here in the UK and reduce the amount of material that needs to be shipped?

Did you set them up as limit switches or home switches?

Additional Information:
Not sure where do I check that?

Additional Information:
Go to config, then ports and pins, then input signals.

Additional Information:
The limits are labeled x++, x— for example.

Click the link to add information to this solution:
I'm using Mach3. I have 2 limit switches on X, 2 on Y and 1on Z for retracted/home. I can go to diagnostics and see the switches/inputs working. But when I move with jog or gcode they have no effect. Also I can go right past the soft limits. I must have something turn off but I don't know what.

The lead screw must be held in position axially. In other words, you don't want your lead screw to move back and forth at all. This is the only way the coupling hub that is attached to the end of the lead screw could be moving away from its coupling assembly. Depending on the lead screw that you are using, the combination of bearings and collars/nut keep the lead screw in place.

Click the link to add information to this solution:
I am almost done with the book build Cnc machine, but when I run the motors from mach 3, the 1/2" coupling comes out of the middle spider (the joiner which connects 1/4 and 1/2" coupling. How do I prevent this?

You can find the datasheets to our motors be going to the the stepping motor category page https://www.buildyourcnc.com/category/nema and selecting the motor. This will bring you to the product page for the motor and all of the motor information will be found there.

Click the link to add information to this solution:
I would like to design my own CNC router around one of your electronics bundles, either the 3 Axis - Heavy Gantry or 3 Axis - All Large Motors. Do you have the data sheets for the motors so that I can use the dimensions in my model?

Modifying the Z-axis to accommodate a larger motor will be a worth while task and is possible, however we have not calibrated the z-axis therefore using the 1600 Steps-per inch in the motor tuning on our machine in our shop. We have not noticed any significant depth increments from not calibrating the z-axis but only from zeroing the z axis too close to the material. Also in your design did you specify the actual depth and the length of tool (end mill/ bit) that you are using?

Click the link to add information to this solution:
I bought a Blacktoe 2 x 8 three years ago and have always had a problem with the Zid axis. No matter how tightly I've calibrated the axis it always cuts to deep. Can I put a larger Stepper motor on Z-axis using the same motion electronics that came with the original machine.

Make sure all your bolts/screws are tighten correctly and if using a lead screw make sure your anti-backlash nut is not offset. Now a default setting will be 10101100 for your driver dip switch settings and in motor tuning (mach3) 1600 steps per, 400.02 velocity, 4 in acceleration. now the acceleration and velocity can be adjusted to move your machine faster, but if set to high they could stall. Make sure you have the correct wiring from your motor to your driver (https://www.buildyourcnc.com/Documents/PN.SM60HT86-2008BF-U%20(inhouse%20PN.60BYGH303-13)%20(1).pdf).

Click the link to add information to this solution:
I have your Nema 24 electronics kit and am having problems with the Z axis dropping over time. I am using a PC 8902 motor. Any ideas on what the problem is? What should be the motor tuning values in Mach3? Thanks

Are you referring to the 425 oz-in motor? How many motors and drivers have you connected? If you have connected more than one, are they all sounding the same?

Additional Information:
it's the 650oz motor. but I think I've got the problem solved. The motor tuning was way out of whack.. I hooked up the smaller 425oz motors and they were ALSO acting funny so I knew it was not them. Software.

I'm still trying to find out what the best speeds are, so there is still some stutter and skipping. thanks for the quick response though, much appreciated.

-james

Additional Information:
You will also want to look at your microstepping. Consider determining your expected mechanical steps per inch and desired jog speed (ipm) and you should have fewer issues. Use the formula: (motor steps * microsteps) / (number of inches of travel in one turn). The ipm for pulley or sprockets should be in the 500-1000 ipm range and for 5 start lead screw, in the 100-200 ipm range. The acceleration can be in the range of 10-40 depending on the mechanics and inertia involved.

Additional Information:
If you ask a question here like: what steps per inch should I set my axes? You will get the standard settings for our machines.

Click the link to add information to this solution:
connected 625oz motor using wire diagram, but motor sounds like it's skipping, am I doing something wrong or is this part DOA? I tried every combo of wiring up, some errored the controller, but the ones that 'worked' still sound terrible. Where do I go from here? - thx! -james

Yes, I can furnish the redFly system without motors. You can request a quote for this at customerservice@buildlyourcnc.com

Click the link to add information to this solution:
[422] I'm interested in using Mach4 and already have 3 motors (425 oz-in). Is it possible to get a electronics system without the motors?

We carry several sizes of lead screw and stepper motors on our website, for example here https://buildyourcnc.com/Item/mechanical-leadscrews-lead-screw-!5-5-starts-10-tpi and here https://buildyourcnc.com/ProductSearchResults.aspx. Please call us at 281-815-7701 to discuss the particular lengths you would need and shipping options.

Additional Information:
https://buildyourcnc.com/ProductSearchResults.aspx is not working

Additional Information:



Additional Information:

Click the link to add information to this solution:
I have a project very similar to cnc machine. I need 3 lead screws of 1.8 m with all set (supports, bearings...etc). and 3 NEMA 42 motors that I can connect with. if those are available, I need the information about shipping to Oman or UAE.

Since the nozzle is getting warm, much of the laser energy is not exiting the aperture and is hitting the inside of the nozzle. You need to align the laser's final mirror to direct it out of the nozzle's aperture and you will have more than enough energy to cut 1/8" acrylic efficiently.

Click the link to add information to this solution:
I've been unable to cut through acrylic or wood at a thickness of 1/8" or less with the BlackTooth. Even with multiple passes (x10) and full power, a clean cut cannot be accomplished. Based on videos I've seen something doesn't seem right. I noticed that the nozzle gets very warm, almost untouchable during even short runs.

You can use the Pokeys57CNC board with our 3.0 amp drivers. The Pokeys57CNC has all of the headers necessary to provide the pulse train to any common stepper driver.

Here is the link to the Pokeys57CNC interface board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Here is the link to the 3.0 amp stepper motor driver:
https://www.buildyourcnc.com/item/electronicsAndMotors-stepper-driver-3!0a

Click the link to add information to this solution:
I'm planning on using your 425 oz motors and need help on selecting the right interface and driver boards. The PoKeys57 CNC USB card looks good but I wonder if the 2.5 amp driver boards shown with it are enough for the 3 amp motors?

If there is play within the motor itself, then that motor may be defective. Call us to provide us more detail on this issue.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:
Ins9kru1

Additional Information:
-1 OR 2+486-486-1=0+0+0+1 --

Additional Information:
-1 OR 2+693-693-1=0+0+0+1

Additional Information:
-1' OR 2+890-890-1=0+0+0+1 --

Additional Information:
-1' OR 2+307-307-1=0+0+0+1 or 'HN9afNei'='

Additional Information:
-1" OR 2+88-88-1=0+0+0+1 --

Additional Information:
1'"

Additional Information:
1����%2527%2522

Additional Information:
@@mxOzC

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I have NEMA 34 motors for a GreenBull 6x12. After 2 weeks of use, my Y axis motor has developed play in the front but not rear of the motor. Is this a motor defect or has something come loose somewhere? Thanks,

This is most likely a wiring issue. I would disconnect all of the power to the drivers and reconnect one at a time to isolate the problem.

Additional Information:
that was not helpful. I already did that way before submitting this question. there are not that many wires here and I have already rewired this a few times. I actually think its a software or interface board issue because it does work sometimes but then trips (possibly a amperage / voltage issue) I am using the interface board that has a parallel port and usb for 5V. are there different settings that I need to setup?

Click the link to add information to this solution:
I'm using the big 651oz in stepper motor for X and Y and the smaller 325 for the z and X and Y keep tripping when I try to tune the motors on Mach3 but Z seems to work. I have to turn power on and off to reset....is this a wiring issue?

I will send two 8mm to 1/2" couplings to you ASAP. Please send an email to customerservice@buildyourcnc.com so I can determine to whom to send the couings. Thanks.

Additional Information:
Please notice, I followed up with several emails abut this situation. In one, I corrected the motor shaft sizes to 10mm. I understand that, as a result of my emails, the original 1/4" x 1/2" couplers were sent and apparently received by someone at the wrong address. As of this time, I have received no couplers of any size and have gotten no reponses to my emails. Can you enlighten me?

Additional Information:
I looked all throughout my email and I cannot find an email from you. Please send an email to phooddaniel@gmail.com so I can determine who this is and to whom I need to send the new couplings. Thanks

Click the link to add information to this solution:
I ordered two NEMA 23 steppers with 1/4" shafts, I received motors with 8mm shafts. I also ordered two 1/4" x 1/2" couplers, which I have not received. I have no problems with the motors, but I will need couplers to match the 8mm shaft to 1/2" lead screw.

Attaching two motors in parallel is possible, but you will need another motor and driver for the opposite side. Each motor must have its own driver to work accordingly and fluently. The two can be wired together, to the same pins on your breakout board and set the dip switches on the driver to match the ones on your x-axis(ex). But remember to view the orientation of the motor and which way it spins, since it is on the opposite side it will have to be orientated correctly to move in sync with the other motor.

Click the link to add information to this solution:
I just finished building my first CNC with the electronics I purchased from you and I am already thinking about improving it. I would like to build a 2 motor X axis solution. Is it possible to attach 2 parallel motors and drivers to the BlueBrew Breakout Board? If so, how?

This may be an issue of conventional vs climb cutting direction. I would recommend trying the opposite on your inside profiles and pockets and check. Let me know if this worked and what you are using for your inside cuts before the change.

Click the link to add information to this solution:
mach 3 pockets cuts are 0.5mm undersized always but outside cuts are prefectly accuracte, i have tried both parallel version and the 100 Khz rnr motion controller, i'm using DM542 as my motor controllers there are no errors in my codes or no mechanical errors

By USB power do you mean the USB board? or do you mean that it is powered through USB but you have the parallel breakout board?


Additional Information:
I was referring to USB Board. Thanks for responding but that issue was resolve. I noticed that Mach 3 was downloaded twice. I copied and pasted RNR file to second copy of Mach 3 and motor runs properly. Should I remove one copy of Mach3 so there is only one? Seems like that could cause confusion. Thanks

Additional Information:
I was referring to USB Board. Thanks for responding but that issue was resolve. I noticed that Mach 3 was downloaded twice. I copied and pasted RNR file to second copy of Mach 3 and motor runs properly. Should I remove one copy of Mach3 so there is only one? Seems like that could cause confusion. Thanks

Additional Information:
I was referring to USB Board. Thanks for responding but that issue was resolve. I noticed that Mach 3 was downloaded twice. I copied and pasted RNR file to second copy of Mach 3 and motor runs properly. Should I remove one copy of Mach3 so there is only one? Seems like that could cause confusion. Thanks

Click the link to add information to this solution:
I'm new to this and was wondering if I connected something incorrectly... I followed the schematics found on this site for wiring. I purchased the heavy gantry kit with the USB power option. All my lights come on and motor shafts resist turning but, I cannot get movement from Mach3. How do I test my equipment to see if I've damaged anything?

Red is A+
Blue is A-
Black is B+
and Green is B-

Click the link to add information to this solution:
I purchased the 3 Axis Heavy Gantry Electronics /w Pokeys57CNC controller and the motors supplied only have 4 wires coming out of them (R,G,B,Blk). Your wiring video shows wiring 8 cables. do you have a video showing how to wire the 4 wire version?