Yes, the redLeaf plug-and-play CNC electronics can include a THC (Torch Height Controller) and motors of any size. The limit of the number of motors that this package can include is 8 motors in total.

Click the link to add information to this solution:
Will the redleaf package allow me to run a torch height controller and 2 nema 34 motors for my gantry? I would prefer to have motors on both sides of the machine with a heavy gantry

The redLeaf CNC computer systems will have either Mach3 or LinuxCNC installed as per the customer's request. If the Mach3 license is purchased, the license file will also be installed on the redLeaf CNC computer system.

The Mach3 or LinuxCNC settings will be configured during the assembly of the system. We contact the customer to determine the drive (mechanics) and inertial (weight of gantry and other parts of the gantry) specifications in order to correctly configure the steps per inch, velocity and acceleration.

Click the link to add information to this solution:
I ordered a redLeaf with Mach3 installed. Do you guys configure any of the setting in mach3 or will I need to do that all myself?

You can find the datasheets to our motors be going to the the stepping motor category page https://www.buildyourcnc.com/category/nema and selecting the motor. This will bring you to the product page for the motor and all of the motor information will be found there.

Click the link to add information to this solution:
I would like to design my own CNC router around one of your electronics bundles, either the 3 Axis - Heavy Gantry or 3 Axis - All Large Motors. Do you have the data sheets for the motors so that I can use the dimensions in my model?

The drivers have quite a bit of protection, so you probably won't ruin anything. You motors are jumping and that is just the motors engaging from getting power from the power supply.

There could be many reasons your motors don't turn. Consider these troubleshooting tips:

- If you are using our parallel breakout board, make sure that the step pins are set for active low (config -> Ports and Pins -> Motor Outputs -> the steps pins should be enabled and set active low)

- The parallel breakout board is powered (connect the USB to the computer using a USB cable)

- In Mach3, make sure you have jog enabled (a little green button at thelower middle of the page in the program run screen).

Additional Information:


Additional Information:
DS26

Click the link to add information to this solution:
My stepper motors stopped working all of a sudden. Mach 3 is running fine, just no signals getting to the motors. The lights on the motor drivers began blinking erratically when this started. Any advice where a problem like this can come from would be greatly appreciated.

Attaching two motors in parallel is possible, but you will need another motor and driver for the opposite side. Each motor must have its own driver to work accordingly and fluently. The two can be wired together, to the same pins on your breakout board and set the dip switches on the driver to match the ones on your x-axis(ex). But remember to view the orientation of the motor and which way it spins, since it is on the opposite side it will have to be orientated correctly to move in sync with the other motor.

Click the link to add information to this solution:
I just finished building my first CNC with the electronics I purchased from you and I am already thinking about improving it. I would like to build a 2 motor X axis solution. Is it possible to attach 2 parallel motors and drivers to the BlueBrew Breakout Board? If so, how?

If you are looking for the drivers to pair with NEMA 34 stepper motors, you can find the 6.0 amp drivers here:
https://www.buildyourcnc.com/item/electronicsAndMotors-stepper-driver-6!0a

The other electronics to send the signals to the 6.0 amp drivers (the control board that operates with the control software) is subject to personal preference, but here they are listed:

Our breakout board (works with Mach3 and LinuxCNC and requires a parallel port on your computer):
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

The PoKeys57CNC (works with Mach3 and Mach4):
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Generic USB breakout board (works with Mach3):
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Additional Information:
Do I need a driver for every motor or can I use one driver for all four motors

Additional Information:
Each motor needs its own driver.

Click the link to add information to this solution:
I have Nema 34 motors but I need the electrical components do you have a kit without motors included?

If you are looking for the drivers to pair with NEMA 34 stepper motors, you can find the 6.0 amp drivers here:
https://www.buildyourcnc.com/item/electronicsAndMotors-stepper-driver-6!0a

The other electronics to send the signals to the 6.0 amp drivers (the control board that operates with the control software) is subject to personal preference, but here they are listed:

Our breakout board (works with Mach3 and LinuxCNC and requires a parallel port on your computer):
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

The PoKeys57CNC (works with Mach3 and Mach4):
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Generic USB breakout board (works with Mach3):
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Additional Information:
Do I need a driver for every motor or can I use one driver for all four motors

Additional Information:
Each motor needs its own driver.

Click the link to add information to this solution:
I HAVE NEMA 34 MOTORS BUT NEED THE ELECTRICAL COMPONENTS DO YOU A KIT WITHOUT INCLUDED?

Recommend first test to check a non-working axis, is to connect the current working axis(ex X-axis) to either the y/z axis to test the actual board and wiring in other axis setup. If tests failed and working (x-axis setup) does not working in the new axis location, go the Planet-CNC/File/Settings/Axes and check if your current non-working axis setup requires a inverted pulse. Check box and test again.
Next test if first fails, is to check continuity in your wires. A simple multimeter(ohm's) will work, just connect the positive and negative ends to one side of the same wire and if reading comes to 0.000, wire has continuity and if reads 0.L then there is a break in the wire and should be replaced.

Click the link to add information to this solution:
I installed the USB CNC Planet and got out of your USB controler $ 75 .Viska have linked to a video 'Party - 2.. X - running and y and z-axis does not work, it moves step motors and controller positions X -axis works, and Y and Z does not work.

To replace all of the electronics for a 4 axis system with all NEMA 34 motors, you will need the following components:

4 NEMA 34 stepper motors:
https://buildyourcnc.com/item/electronicsAndMotors-nema34-651ozin

4 drivers (one driver for each motor):
https://buildyourcnc.com/item/electronicsAndMotors-stepper-driver-6!0a

One controller:
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

24v Powers supply for the controller:
https://buildyourcnc.com/item/electronicsAndMotors-power-supply-24v-1a-dc

2 48V power supplies for the motors and drivers:
https://buildyourcnc.com/item/electronicsAndMotors-power-supply-24v-36v-48v

Click the link to add information to this solution:
what do i need to buy for a complete replacement 4 axis cnc mill nema 34 motors mach 3

Sure, our blueChick and blackToe CNC Routers are considered relatively small machines at 1'x3' and 2'x4' respectively. They both use NEMA 23/24 motors. We recommend connecting the machines to either Mach3 or LinuxCNC and come with the necessary interface for either control software. You will need a computer for the control software and if you desire LinuxCNC, you will need a parallel port. Mach3 will accept either parallel port, or USB interface.

Click the link to add information to this solution:
I recently purchased the linksprite cnc engraving router and was wondering if your 3 axis small kit would be ok? the engraver came with nema 17 motors and a arduino board but but not liking the grbl control. could you point me in the right direction .Thanks.

That shouldn't be a problem. I will need the current rating for the motors. We can subtract the price of the motors. and you can add you own. If you want us to solder the cable to the round connectors and them motor, you would need to send the motors to us.

Let me know and I can send a paypal invoice for the redLeaf without motors.

Click the link to add information to this solution:
DON'T WANT TO USE MY OWN MOTORS FOR THE REDLEAF CNC COMPUTER SYSTEM.

When dealing with 3rd party machines, we have a universal setup that will fit almost any other machine, although please take in consideration the specifications in which your stepper motors and drivers are used and set to!
Now changing the controls, would be more or less changing the Breakout board/interface board to a different one that might use a different program to run your machine. Usually you will not need to change your interface board or breakout board, unless the 3rd party manufacture made it specifically to that set up.

Click the link to add information to this solution:
I purchased a 3040 CNC router off eBay a year ago and would like to change the controls. The steppers are 185oz.in motors. My question do i need to purchase a interface board and break out boards?

We offer a laser/spindle Z-axis attachment for our 4x8 greenBull CNC. The blackFoot 4x8 does not have a large enough gantry to accommodate the 40W laser tube.

Additional Information:


Additional Information:
We do sell the parts to convert your CNC milling machine to a laser, but you will need to develop the mounts that will hold all of the laser parts to the machine, if the machine was design and built by you.

We can offer guidance for this conversion.

The laser parts can be found here:
https://www.buildyourcnc.com/LaserComponents.aspx

Click the link to add information to this solution:
I already built a 4 x 8ft carving machine, I would like to modify for laser cutting wood. Do you sell a conversion kit? I use Mach3 software and steppers. Thanks Ray

As long as the Ethernet cable is not next to stepper motor cables (between the stepper motor and the stepper motor driver) you should be fine. If you are using a spindle, make sure to shield the cable between the spindle and the VFD as well.

Additional Information:
One of my customers is testing this scenario. He is using CAT7 Ethernet cable which is double shielded. I/He will post the results when tested.

Click the link to add information to this solution:
I would like to mount the CNC controller to the gantry and use the ethernet cable routed through the cable carrier, is ther ok?

Yes, I can furnish the redFly system without motors. You can request a quote for this at customerservice@buildlyourcnc.com

Click the link to add information to this solution:
[422] I'm interested in using Mach4 and already have 3 motors (425 oz-in). Is it possible to get a electronics system without the motors?

The blackToe 2'x4' cnc machine is sold as a kit only. We offer plans for the scratch (book) build machine that can be found here for purchase and also comes with a DVD showing the build process: http://www.buildyourcnc.com/cnckitintro.aspx and the plans for build in the book is on the CNC book page: http://www.buildyourcnc.com/Book.aspx.

You can use the same size stepping motors referenced in the book: http://www.buildyourcnc.com/category/elcombo

Click the link to add information to this solution:
I would like to build the 2’x 4’ blackToe2x4v40 CNC router. I have your book. I want to build the latest model blackToe2x4 v40. Are those the correct plans on your web book page ? Is there a bill of materials? If I use a Porter Cable 3-3/4 router motor what size stepper motors do I need?

The diagram for wiring the USB interface board is located here: https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/

Under the board illustration, there are three smaller diagrams of limit switch wiring. On each, there are two connections, the GND and the pin which are labeled at the ends of the circuit on the diagrams. The pin side would go to the axis label ++ or -- terminal (i.e. X++, or X--). The other end, labeled GND would connect to any ground terminal on the board.

Click the link to add information to this solution:
I am using 5 limit switches on my 3 axis machine. I am using the usb controller for planet cnc. I would like to know where all the wires related to the limit switches get connected? A diagram would be helpful.

CNC kits normally take 5-7 business days but during busy periods this can increase.

Click the link to add information to this solution:
Hello, I purchased a cnc kit 3 days ago and I would like to know how long does it take to prepare a shipment? thanks

For order inquiries please call us at 281-815-7701 or email customerservice@buildyourcnc.com. Thank You!

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I would like to add to my oder as well. I had the two nema 34 needing to go to 1 and the one nema 24 going to two. i need lead screws and couplings