The RNRMotion driver will not conflict with the mach3 license. Make sure you have the RNRmotion driver in the plugins folder and the provided xml in the main mach3 folder. Also, make sure to have the mach3 license file in the mach3 folder. If you still experience problems, please give us a call.

Click the link to add information to this solution:
i purchased a breakout board from you guy and the rnr motion control is messing with my license in mach 3 tech support at mach said it is the rnr software i need help to contact them and let them see what they can do to help

I will find this answer when I get into the office on Monday, but I have no problem sending out a replacement DVD out to you. If you would like to do this, please call us on Monday and let us know that you need a replacement DVD

Click the link to add information to this solution:
Hi Patrick back in 2013 I purchased the cnc hardware and plans kit. I misplaced the dvd which shows you how to configure the mach 3 software to the cnc machine I build. I it possible to get another dvd. Or do you have the information somewhere you the website or youtube?

I would not recommend slaving an axis using the method of taking an additional axis from the USB interface. Instead, wire both drivers to a single axis on the USB interface. This will insure perfect signal output to both drivers. If you requre the motors to spin in opposite directions, simply wire one of the motors to the driver reversing the coil A and B connections, or use a hex inverter (https://www.buildyourcnc.com/tutorials/Tutorial-Two-Motors-Spinning-Oppositely-On-Single-Axis).

Click the link to add information to this solution:
I purchased a USB Breakout board, motors and drivers, paid for CNC USB Controller Software and I CAN NOT "Slave" an axis, but there is an option to do that. The moment I connect USB Breakout Board "Slave" option becomes shaded and I can no longer select it (becomes not functional). What is going on? Need help asap. Thanks

If you purchase the greenLean, you will get everything you need except a router, computer to operate the machine, and software to control the machine. You state that you have a computer. You can use this computer, but you will need to determine if it has a parallel port, or if you are going to need the USB controller option. As for the software, there are too many different options for you to choose from. We would not be able to tell you which to get, and how much it will cost you. This is a matter of preference. I can tell you, however, that you will need 3 types of software to complete a CNC project. You will need CAD software to design your design, CAM software to add tool paths and convert the design to g-code, and then control software to take the g-code and operate the machine.

Additional Information:
20

Click the link to add information to this solution:
I am building a wet plasma table for my shop that is 8'x 16'. I will need hardware and software. Please heko me wuth the list, My phone is 9124273734. I would like to talk with someone if possible. Thanks, Rus

Yes, you can connect a THC, Torch Height Controller, with the Mach3 USB controller. The THC uses the inputs to determine if the z axis needs to move up or down according to the arc of the plasma torch. The THC connects its outputs to the inputs of the controller so the controller will be informed of the states of the plasma torch.

Click the link to add information to this solution:
I am installing a mach 3 usb controller into a wright cnc plasma table and I need instruction on wiring the thc (proma compact ) torch height controller to this board. IE will this board work to replace the parallel port board with usb controller board?

Your deduction of the power supply at fault is probably correct. When you attempt to power the power supply, check the V+ and V- (COM) with a multimeter on the DC setting. You should measure 36 volts.

If there is no voltage on the V+ and V- (COM) there should be a fuse inside the power supply that you might want to check. Also, while you in there, check the electrolytic capacitors. Electrolytic capacitors have a finite lifespan much shorter than other components and are often the cause of many problems with all electronics.

Please let us know what you find.



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
My machine stopped today (after many fun filled hours of operation in the last 3+ years). I suspect the 36V 8.8 amp power supply as there is no power to the stepper motors. Is there a breaker to check, or do I need to get another power supply? Should I assume the stepper motors are OK?

The steps per unit is automatically determined in the calibration of the axis by clicking on the "set steps per unit" button above the reset button on the settings tab. Initially set the velocity and acceleration to a low setting, like 100 and 10 respectively, so that the axis does not stall during this operation. Once calibrated, the steps per unit will be set to the correct value and the velocity and acceleration can be increased. I have a video explaning the tuning of the motors on this page:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

The name of the video is Test and Tune the motors.

Click the link to add information to this solution:
I purchased the large gantry system with USB control. I have built the CNC and it is working fine. Now fine tuning the motors. On the X-axis I have the Velocity set at 60 (inches), Acceleration at 1.4, the Step Pulse 1-5us and Dir Pulse set at 0. Do I need to adjust the pulses?

The Mach3 USB interface board will require a 24V power supply to enable the use of the input, output terminals, and the spindle VFD 0-10V and output for speed control.

Click the link to add information to this solution:
Hi Patrick right now I have a parallel port cnc machine that I built in 2013 using the hardware and components I purchased from your website. I want to update my system by changing my current parallel port interface board to a Mach3 USB interface board from your website. Is the Mach3 USB interface board all I need to do this or is there other components I need to get. please advise.

Sure, our blueChick and blackToe CNC Routers are considered relatively small machines at 1'x3' and 2'x4' respectively. They both use NEMA 23/24 motors. We recommend connecting the machines to either Mach3 or LinuxCNC and come with the necessary interface for either control software. You will need a computer for the control software and if you desire LinuxCNC, you will need a parallel port. Mach3 will accept either parallel port, or USB interface.

Click the link to add information to this solution:
I recently purchased the linksprite cnc engraving router and was wondering if your 3 axis small kit would be ok? the engraver came with nema 17 motors and a arduino board but but not liking the grbl control. could you point me in the right direction .Thanks.

The 8 wire motors need to be wired in bipolar parallel configuration. The wiring is as follows: Red and Blue to A+, Yellow and Black to A-, White and Brown to B+ and Orange and Green to B-. To find the wiring for the 4 wire motors, the wiring is Red to A+, Orange to A-, Blue to B+ and Green to B-.

Click the link to add information to this solution:
I have constructed the cnc router machine as shown in woodsmith magazine. I have purchased the 3 Nema stepper motors. The one larger motor has 4 wires, as do the other two. However, on the schematic, the Z, and Y axis motors indicate 8 wires each. Did I go wrong, or are there different Nema 23 motors?

Attaching two motors in parallel is possible, but you will need another motor and driver for the opposite side. Each motor must have its own driver to work accordingly and fluently. The two can be wired together, to the same pins on your breakout board and set the dip switches on the driver to match the ones on your x-axis(ex). But remember to view the orientation of the motor and which way it spins, since it is on the opposite side it will have to be orientated correctly to move in sync with the other motor.

Click the link to add information to this solution:
I just finished building my first CNC with the electronics I purchased from you and I am already thinking about improving it. I would like to build a 2 motor X axis solution. Is it possible to attach 2 parallel motors and drivers to the BlueBrew Breakout Board? If so, how?

Yes, you will need the Mach4 legacy plugin to make the parallel port and Breakout board work.

Click the link to add information to this solution:
Do I use the blue brew BOB that I purchased in conjunction with the Mach 4 PPL Plug-in provided with Mach 4 software when I purchase It?

The on/off laser control for the blackTooth laser system is controlled by software. Software controls a digital trigger on the laser power supply that turns the laser on and off.

Our blackTooth works more like a CNC machine where g-code is used as the instructions to cut and engrave. Generally, CNC machines have a z-axis that moves up and down. When the z-axis is moving down, the end mill (cutting tool) is penetrating the surface of the material to be cut. We use this same technique to control the laser on and off. If the z-axis is in the down state, the laser is on. If the z-axis is in the up state, the laser turns off. All of this is automatically generated in the g-code when the machining operations are created in CAM software. This eliminates the need for an expensive laser controller board; however, a traditional laser controller board can be used with our system.

Click the link to add information to this solution:
I am looking at purchasing a blacktooth laser system but after reading some of the post I am unsure if laser power is under software control. Is laser power ( on/off) directly controlled with the off the shelf hardware and software

There is some variation in the outward appearance of laser power supplies due to sourcing through different vendors. However, the basic wiring requirements are the same in each case. For the unit with integrated laser controller, follow the diagram found here: https://buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx#prettyPhoto/0/. The terminals on the signal side will have a 6 connection terminal block -- these are the ones labeled 5V, IN, G, P (or WP), L (or TTL-L), and H (or TTL-H). The High Power side will have 3 inputs for AC power, one high voltage lead, and one return line. Connect these as shown in the diagram as well: the return line goes on the "front" (beam exit end) terminal of the laser tube, the high voltage lead goes to the "back" terminal of the tube, the FG terminal (or G) receives the earth ground wire of the AC power cable, and the two AC terminals receive the line and neutral wires of the AC power cable (it doesn't matter in this case which wire goes to which terminal).

Click the link to add information to this solution:
I purchased the blackTooth Laser Engraver with integrated Laser Control Unit and have been following your instructions. I noticed that the laser tube power supply is different that what is shown in your instructions. Do you have any better wiring guides that I can follow for the version that I received?

Please email us at customerservice@buildyourcnc.com for replacments/refunds.

However dealing with Autodesk Fusion, did you choose the postprocesser ending with g-code or Mach 3? Using these postprocesser's will work with the planet-cnc program!
Our parallel BoB, with linux-cnc or Mach 3 will work with the arch definition.

Click the link to add information to this solution:
Planet-CNC's USB Controller Software doesn't support the arc definition. Can I get a refund for their hardware I purchased from you? I need something that supports gcode generated by Autodesk Fusion or supports the gcode definition http://linuxcnc.org/docs/html/gcode.html ?

Yes, the 651 oz/in motor requires a driver that is compatible to the motors (the motor will draw 6 amps max and the driver paired with this motor will be able to allow for a 6 amp draw). I would also recommend a 36 volt power supply for better high velocity performance.

Click the link to add information to this solution:
I have one of your smaller stepper motors running my X AXIS bridge crane and if it is moved to fast the stepper motor sounds like it is skipping steps will the 651oz stepper motor require a different power supply and controler?

Absolutely, I can answer this type of question and anything other questions you may have with your new-to-you CNC router.

Additional Information:
20

Click the link to add information to this solution:
[789] Can you help me with selecting a power supply ( and a few other components ) for the stepper motors that came with a homemade CNC Router I just purchased.

I can provide a paypal invoice for the difference in price. Just give me an email at customerservice@buildyourcnc.com and then I can send you the invoice.

Additional Information:
I can provide a paypal invoice for the difference in price. Just give me an email at customerservice@buildyourcnc.com and then I can send you the invoice.

Additional Information:
thats great thank you. please send it to james_moya@hotmail.com and i will be paying with my cc.

Additional Information:
thats great thank you. please send it to james_moya@hotmail.com and i will be paying with my cc.

Click the link to add information to this solution:
i placed an order with you on 5.27.20 for 3 stepper motors. i realize now i need the rest of the electronics (drivers, breakout board power supply etc...) i see you offer a bundle and would like to know how i can get the rest of the bundle. im looking at the $390 bundle without the motors obviously. please advise. thank you

Yes, the 651 oz/in motor requires a driver that is compatible to the motors (the motor will draw 6 amps max and the driver paired with this motor will be able to allow for a 6 amp draw). I would also recommend a 36 volt power supply for better high velocity performance.

Click the link to add information to this solution:
I HAVE ONE OF YOUR SMALLER STEPPER MOTORS RUNNING MY X AXIS BRIDGE CRANE AND IF IT IS MOVED TO FAST THE MOTOR SOUNDS LIKE SKIPPING STEPS WILL 651OZ REQUIRE A DIFFERENT POWER SUPPLY CONTROLER?