No, you do not need another motion controller if you have the parallel breakout board and you are using the "Legacy Parallel Port Plug-In" with Mach4. The motion controller is the parallel port.

Click the link to add information to this solution:
I purchased hardware for my plasma table which included 3 nema 34 stepper motors and drivers, power supply,Blue brew BOB, and Mach 4 Control software with parallel port plug-in. In configuring the Mach 4 software it asks for a motion controler. Do I need another device such as a smoothstepper motion controler?

Here is the new link to the Planet CNC software download page: http://planet-cnc.com/software/

You can try the software as a demo however you will have limited g-code lines you can run. I believe it was around 500, so you can create small items with the demo.
To fully unlock the Planet-CNC software you will need to purchase the license.

Click the link to add information to this solution:
I purchased the USB BOB and the link for the Planet-cnc software is broke. Will I need to purchase a license for the software as well?

When you plug the USB controller into the computer using a USB cable, and the planet-cnc software is running, you will be presented with a dialog box that will contain a text box for the key that you received from the planet-cnc folks.

Additional Information:


Additional Information:
Is there any other software that will work with your controller Mach3? Thanks for the help!

Click the link to add information to this solution:
However it how do I get the software to work? PlanetCNC sent me a key that looks like it will only work with a backup control board I purchased from them?

Mach3 is not compatible with the USB breakout board, so you need Planet CNC in its place.

Additional Information:

I am confused by this same issue. I am using the Mach3 USB interface board with Mach3 and it works fine. In fact a video of it is on this very website. (link below)

Is the Mach3 USB interface board the same thing as Planet-CNC USB board?
It has been stated on this FAQ that it cannot be used with Mach3 and can only be used with Planet CNC USB software.

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
In a Windows configuration, Using the USB breakout board, is the Planet-CNC software used in conjunction with Mach3 or in place of it?

To home the z-axis using a plate:
- Connect the end mill using a large clamping device like an alligator clip with a wire connected to GND.

- Connect the plate (solder a wire to the plate) to one of the input pins.

- You can use the autoset to setup that pin in Mach3 simply by touching the two together once connected to the pin and GND.

Alternatively, the end mill can be connected to the pin and the plate connected to GND as long as there becomes a complete circuit when the end mill touches the plate.

To setup homing for the Planet-CNC homing and limits, go to the Planet-CNC Machine setup page which explains the process step by step: http://www.planet-cnc.com/faq/machine_setup/

Customer Response:
How do I get homing on z to work with planet cnc software using build your own usb board. I have gone to planet website and followed the instructions provided but my software will not allow entries in the required fields they are grayed out is it because I am not using planet-cnc's board, I have used this method for years with Mach3 and would like to use it with the usb board and software.

Answer:
Just received information from the developer. The instructions on how to use a plate for z-axis homing (moveable sensor) can be found here:

http://www.planet-cnc.com/faq/moveable_sensor/

Click the link to add information to this solution:
How do I get Homing on Z to work with Plate and Ground using Buildyourcnc usb board all the entries for the sensor in planet-cnc are grayed out. I am using input z- and I purchased the software

After you purchase the license, we provide you with the license file. That file needs to be manually copies to your mach3 folder. The mach3 folder is usually on the C: drive (C:\Mach).

Copy the file that was emailed and copy it to the c:\Mach3 folder.

Go to the about menu option in Mach3 and confirm that your name is on that dialog box.

Additional Information:
My name is not on the dialog box

Additional Information:
Its mach 4 dumass

Click the link to add information to this solution:
I reciently purchased Mach 4 and sowenloaded the license. After creating the profile and working with the program it is still in the demo mode. The drop down tells me that it is sucessfully installed. Please help.Thanks

You can purchase the BobCAD-CAM as a bundle with any of our machines.

Click the link to add information to this solution:
Can you purchase the BOBCAD-CAM software alone, or in with the combination LaserCutter, or is it only available for the price listed in combination with the blackfoot CNC

You can find instructions for the Mach3 USB here:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

You will probably need to use the Mach3 USB board with Mach3. We have not tested the Mach3 usb card with Mach4.

Click the link to add information to this solution:
Whereb can I find directions on how to install the Mach3 USB board with Mach 4 software? I do not have a parallell port.

The best place to find information and step by step instructions for Mach4 is to use the manuals provided by MachSupport.com.

Here is a link to the PDF manuals for Mach4: http://www.machsupport.com/help-learning/product-manuals/

Click the link to add information to this solution:
I purchased Mach 4 control software and am in need of a very elementary tutorial on set up. I am extremely new to this and need step by step help. Thanks

if you purchased the USB interface, you will need planet-cnc software rather than Mach3, and you will need a usb cable to connect the usb interface to the computer.

The blackToe 2x4 CNC Machine Kit with optional table will need wire to connect the electronics. Don't forget to get some end mills to use for cutting the intended material.


Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
If I purchase the [blackToe 2x4 v4.1 CNC Machine Kit - USB Electronics - Table Included] all I would need for this CNC to be fully operational is a laptop with mach 3 software and a router. Is this correct?

If you were logged in when you made the purchase, you can click the "My Account" link at the top of any page on this website and see all of your orders, order line items (with direct links to these items), and shipment information.

Here is a link to the "My Account" page for your convenience:
https://www.buildyourcnc.com/CustomerInfo.aspx

I did not see your username on your internal customer record, so I added this username and you should be able to see the information in the "My Account" page.

Additional Information:
I just tested your accounts page and the cable carrier links are in there. Thanks and please let me know if you need further assistance.

Click the link to add information to this solution:
I have purchased cable carrier chain and would like to know if you could send me a copy of that order as I need to purchase extra lengths of the links I bought. Thanks

I will find this answer when I get into the office on Monday, but I have no problem sending out a replacement DVD out to you. If you would like to do this, please call us on Monday and let us know that you need a replacement DVD

Click the link to add information to this solution:
Hi Patrick back in 2013 I purchased the cnc hardware and plans kit. I misplaced the dvd which shows you how to configure the mach 3 software to the cnc machine I build. I it possible to get another dvd. Or do you have the information somewhere you the website or youtube?

If you have the USB controller you will need to purchase a USB controller license from planet-cnc.

Click the link to add information to this solution:
with the blueChick v4.2 can any software be used or doo we need to purchase a lic key from the manufacture of the control board for 75 bucks

You can only use the planet-cnc interfaces with the PlanetCNC software. If you like the software and want to remain with that software, the hardware interfaces will need to be purchased from the planet-cnc folks.

I would recommend using the Pokeys57CNC interface which is compatible with Mach3 and Mach4. You can also consider the Mach3 USB interface if the Pokeys57CNc interface is out of your price range.

Pokeys57CNC product page:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Mach3 USB product page:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
I have registered version of planetcnc software that I purchased with a Chinese controller I want to use 3 better drivers with a separate USB controller can you recommend a controller and how to link my existing software. Regards Lloyd from Australia

CAD drawings are not furnished with the purchase of a machine.

Click the link to add information to this solution:
I have a greenbull 5x Long Z. I thought I read that I would get the CAD files to the machine when I purchased it? I want to make a couple modifications. Thanks!

There are many ways to wire an emergency stop switch. The simplest, and arguably the most certain, way is to wire the switch into the incoming power so that throwing the switch kills all power to every part of the machine. Here is a diagram showing how a customer wired such a switch on their blackTooth laser which you could adapt to your needs. http://www.buildyourtools.com/phpBB3/viewtopic.php?f=12&t=4872

Alternatively, you could use an input pin on your USB board. The wiring would depend on whether and how you might be using limit switches (single or multiple switches; normally open or normally closed). Our website datasheet for the USB board is at https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/ and shows how to configure the switches for each set up. If you use this method, you'd essentially wire the e-stop as a limit switch.

Click the link to add information to this solution:
I recently purchased 3 axis electronics with the USB controller board. I'm trying to install an E-stop switch. Where do I connect that on the controller board?

There are many ways to wire an emergency stop switch. The simplest, and arguably the most certain, way is to wire the switch into the incoming power so that throwing the switch kills all power to every part of the machine. Here is a diagram showing how a customer wired such a switch on their blackTooth laser which you could adapt to your needs. http://www.buildyourtools.com/phpBB3/viewtopic.php?f=12&t=4872

Alternatively, you could use an input pin on your USB board. The wiring would depend on whether and how you might be using limit switches (single or multiple switches; normally open or normally closed). Our website datasheet for the USB board is at https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/ and shows how to configure the switches for each set up. If you use this method, you'd essentially wire the e-stop as a limit switch.

Click the link to add information to this solution:
I recently purchased 3 axis electronics with the USB controller board. I'm trying to install an E-stop switch. Where do I connect that on the controller board?

You will need to build the table unit for your machine. There are instructions on how to do this at the bottom of the product page here, https://www.buildyourcnc.com/Item/cnc-machine-blackFoot-v4
There is no estimate on how much this will cost though, since there are too many variables involved to do this.

- PC with parallel port and USB port
- 20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
- 18awg stranded wires for power supply to drivers
- 24awg stranded wires for breakout board to drivers
(location and spacing of components varies from one person to another, so we do not provide cables/wires)
- General purpose extension cord (cut the female end off) to provide power to power supply
- USB cable to power breakout board
- Parallel cable to communicate to breakout board
- Router
- (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
- (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
- End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
- CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
- CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx

This answer is applicable to most of our machines with the exception of the greenLean and the blueChick since those machines are equipped with a table structure.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Can I purchase a computer off Amazon (I have a machine I want to use) and still use the USB interface to drive it with LinuxCNC?

Yes, we can help you with leveling your CNC machine even if you didn't purchase it from us.

Click the link to add information to this solution:
[789] I need to level my cnc machine, but I didn't purchase it from you, so: Do you offer tech support with leveling a cnc? Because I don't see this problem listed .And: Do you offer support if my machine was purchased in China or from another vendor?