Many shielded cables come in various materials and designs, so having one with a copper mesh covering the inner insulator wire is no problem. We currently use a extension cord found locally at a hardware store and include one 18G wire for ground. So a specific shielded cable is not a required, unless being used next to specific and sensitive electronics that are extremely sensitive to noise and voltage interference than a shielded cable is required.

Click the link to add information to this solution:
I purchased a 2.2 spindle a while back and went to the electrical supply house to but shielded cable for the power run, I was on the web a while back and saw a picture of shielded cable that didn't look like what I had bought. should it have a copper like mesh wraped around the inner insulation. Thanks

The blackFoot uses the same electronics and motors as the blackToe (2'x4') machine. The only parts that change are the gantry horizontal structural parts which may be relatively easy for you to change. We can send you those parts if you are interested in a smaller unit.

Click the link to add information to this solution:
I have a Blackfoot that was purchased in 2017, after the purchase we moved and I haven’t been able to find room for it... would you be interested in buying it back or trading for something smaller. The Blackfoot and computer have never run but I did purchase it assembled. Thanks in advance, scott

When did you purchased the VFD and spindle? We only started this after the date of the instagram post that offered this added service.

Additional Information:
I purchased it July 16, 2020 however due to all the 2020 issues, I'm just now completing my CNC and hooking up the VFD and Spindle.

Additional Information:
The service started on Sept 23, 2020. Your order was prior to that.

The soldering is straightforward. If you wish to have me provide this extra service, feel free to send the unit back with the cable and I will solder the cable and do the parameter check and test the VFD and spindle.

Additional Information:
When I purchased my VFD and Spindle, I forgot to purchase the wire for the spindle. I had an electrician run a 220 line and hook up the VFD. But I don't have the wire for the spindle. I'd like to get the one you recommend and just pay you for another connector and the soldering.

Additional Information:
Can I purchase the one you spindle wire you recommend and just pay you for another connector and the soldering.

Click the link to add information to this solution:
You state "If you purchase cabling, we will solder the cable to the spindle and connect the cable to the VFD." I didn't see that when I purchased my spindle and vfd. If I place an order for the wire and another female adapter, will you please solder the connector to the wire?

When dealing with 3rd party machines, we have a universal setup that will fit almost any other machine, although please take in consideration the specifications in which your stepper motors and drivers are used and set to!
Now changing the controls, would be more or less changing the Breakout board/interface board to a different one that might use a different program to run your machine. Usually you will not need to change your interface board or breakout board, unless the 3rd party manufacture made it specifically to that set up.

Click the link to add information to this solution:
I purchased a 3040 CNC router off eBay a year ago and would like to change the controls. The steppers are 185oz.in motors. My question do i need to purchase a interface board and break out boards?

That is a very loaded question that could be replied in so many ways. I will need a more specific question to help you. For instance, I have my machine moving in different directions, but I don't know how to make the machine move according to g-code instructions. Another question could be, I connected all of my electronics and the motors are not moving and I did all of the steps on the electronics video to troubleshoot the problem.

Click the link to add information to this solution:
I have a cnc router that was built from the book "Build your own cnc machine" by james kelley and patrick hood daniel.all the parts were purchased from your company.I have no clue how to work the machine and I need to purchase a spindle (or router) bits , softwear ect , I did mention I don't know how to use the machine !!! Thanks for your help Richard

That order did not show up in our system. We searched and found it in our PayPal activity. We are sending it today. My apologies for this.

Additional Information:
I received my order, thank you. However the collet nut will not fit my Porter Cable 690, the threads are too coarse. Can you please send the correct nut, and I will return the wrong nut.
Thank you,
Tom

Additional Information:
I believe the wrench is different also.

Additional Information:
Ok. I will send the correct wrench and collet nut.

Additional Information:
It’s Monday 11-16, and I have not received the nut and wrench. Have you shipped it yet?

Additional Information:
Let me check.

Additional Information:
The set of collets and nut/spanner came straight from the supplier PreciseBits. I am working to understand what went wrong and get it resolved.

Additional Information:
Do you have any new info on the status?

Additional Information:
It’s now Dec 2nd, I ordered this on Oct 7th. No resolution yet! Still waiting, Not very happy.

Click the link to add information to this solution:
I ordered a collet set for a Porter Cable router on 10/7, my card was charged on 10/8. I have not heard anything from you as to when it would ship, or even a confirmation of the order. Please let me know the status.

CAD drawings are not furnished with the purchase of a machine.

Click the link to add information to this solution:
I have a greenbull 5x Long Z. I thought I read that I would get the CAD files to the machine when I purchased it? I want to make a couple modifications. Thanks!

If you would like to come to the office, please call the office at 281-815-7701 to request a visit at your specified time within our business hours so we can make sure that the right person will be there to assist you.

Click the link to add information to this solution:
I am considering the purchase of a Black foot or Green Bull CNC router and would like to come and visit your facility to see them in person and to discuss my requirements. Please can you tell me your address. I am based in NW Houston. Many thanks.

Currently we do not have that modification kit, our set up is fixed for our greenBull only modification kit we have for this model is the long z-axis kit(Designed for Foam cutting).

Click the link to add information to this solution:
I am building your "Green Bull' 6 foot wide kit and I am at the stage of attaching the motor and drive chain. I would like to know if you have an modification kit available to put the 1/2" ACME screw on the Y-axis?

Here are links to the sole pump and heat exchanger/fan. I am sending you amazon links sine I don't ahve listings of my pump and heat exchanger separately from my cooling system:
Pump: https://amzn.to/3R6zPbj
Fan/radiator (Heat exchanger): https://amzn.to/3UWOuqN

Click the link to add information to this solution:
I RECENTLY PURCHASED A REPALCEMENT 12V DC SWITCHING POWER SUPPLY, HOOKED IT UP BUR DID NOT THE PUMP AND RADIATOR. VERIFIED OUTPUT OF UNIT AT 12V. SO I'M ASSUMING ALSO NEED TO REPLACE CAN YOU SUPPLY ME LINK PURCHASE THEM?

Sure, our blueChick and blackToe CNC Routers are considered relatively small machines at 1'x3' and 2'x4' respectively. They both use NEMA 23/24 motors. We recommend connecting the machines to either Mach3 or LinuxCNC and come with the necessary interface for either control software. You will need a computer for the control software and if you desire LinuxCNC, you will need a parallel port. Mach3 will accept either parallel port, or USB interface.

Click the link to add information to this solution:
I recently purchased the linksprite cnc engraving router and was wondering if your 3 axis small kit would be ok? the engraver came with nema 17 motors and a arduino board but but not liking the grbl control. could you point me in the right direction .Thanks.

See the question on our "Ask the Expert" question-and-answer list on cellular towers under nonionizing radiation for a discussion of RF safety issues associated with cellular radios. The technology underlying cellular radios and base station antennas is similar around the world, but there are differences in systems design and RF safety limits in different countries. For a summary of cellular radio RF safety issues with attention to international differences see the excellent Web page, Cellular Phone Antennas (Base Stations) and Human Health, by John E. Molder, Ph.D., from the Medical College of Wisconsin. Gary H. Zeman Sc.D., CHP

Click the link to add information to this solution:
I LIVE IN ITALY AND WISH TO KNOW MORE ABOUT RADIATIONS CAUSED FROM MOBILE TELEPHONES. TELECOM WOULD LIKE PLACE A WIRE-ANTENNA THE HEARTH OF MY TOWN, I'M AFRAID IT. WHICH KIND RISK HEALTH COULD IT CAUSE? THANK YOU IF WILL SEND ME SOME INFORMATION SCIENTIFIC ARTICLES THIS PROBLEM!

Just specify the full length in the quantity field in the shopping cart and give us a call to inform us of the cut lengths (you can also email customer service - link in the contact us page - link at the footer). We are working on a way to do this at the product page, but won't be finished for a few more days.

Additional Information:
20

Click the link to add information to this solution:
How do I order 3 specific lengths of lead screws in one order? I could only order a single total amount via the shopping process. I require 36", 60" and 14". If I order 110", I will get 79" + 31". Do I have to order 115" and pay for an extra 5" to get around this?

As shown in the instructions the laser tube that was used was a different model which had the metal end, compared to our full glass tube models we currently ship with the machines.
So there is no difference besides appearance between the two tubes.
The focus lens should be placed in the laser nozzle assembly and not on the laser tube itself.


Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I bought a blacktooth laser from you about a year ago.. I am finally getting around to installing the laser tube and I noticed that my tube does't have the metal end on it like all the pictures I've seen. is this a focus lense and can I purchase one?

Come on over and we will assist you in any way you need.

Click the link to add information to this solution:
I purchased a Blackfoot 4ft X 8ft in 2015 I have yet to run it. Do y’all offer any classes that can help me?? I would very much like to have this machine running. Thank you in Dayton Tx

I have very detailed wiring videos for the Pokeys57CNC controller on the pokeys57CNC controller webpage: https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
[50] I purchased 3 Axis Heavy Gantry Electronics /w Pokeys57CNC controller (Mach3 and 4 Compatible) and Cable Pack I plan to use Mach 3 do You have a wiring diagram Thanks

CNC kits normally take 5-7 business days but during busy periods this can increase.

Click the link to add information to this solution:
Hello, I purchased a cnc kit 3 days ago and I would like to know how long does it take to prepare a shipment? thanks

It's generally acceptable to use one pin for all of your limit switches wired Normally Closed (NC), and another separate pin for a Z probe that is Normally Open (NO). LinuxCNC is quite flexible and allows for mixed configurations of NC and NO switches.

Just ensure you configure LinuxCNC correctly to recognize each pin's logic (Active low or active high). And perhaps run a few tests before running the machine.

Additional Information:
It's generally acceptable to use one pin for all of your limit switches wired Normally Closed (NC), and another separate pin for a Z probe that is Normally Open (NO). LinuxCNC is quite flexible and allows for mixed configurations of NC and NO switches.

Just ensure you configure LinuxCNC correctly to recognize each pin's logic (Active low or active high). And perhaps run a few tests before running the machine.

Click the link to add information to this solution:
[59] is it ok to use one pin for all of the limit switches wired NC and another pin for a z probe that is NO, or do all input pins need to be the same (NC or NO)? I would like to use LinuxCNC but will use Mach3 if necessary. a thanks!

Here is the new link to the Planet CNC software download page: http://planet-cnc.com/software/

You can try the software as a demo however you will have limited g-code lines you can run. I believe it was around 500, so you can create small items with the demo.
To fully unlock the Planet-CNC software you will need to purchase the license.

Click the link to add information to this solution:
I purchased the USB BOB and the link for the Planet-cnc software is broke. Will I need to purchase a license for the software as well?