I also place the controller very close to the drivers (on the back of the gantry). All of the cables are shielded. The only long cables are the mains power cables and the USB cable. The USB cable is shielded and contains active repeaters.

There is no problem putting all of the electronics in a box and using long cables to the motors. This is the way I did it for a very long time.

Click the link to add information to this solution:
Great site. I saw your videos of wiring the Mach3 USB controller. You place the drivers next to the Steppers. This means that you have very long leads to the USB Board? What about the placement of the controlling PC? Is it a problem to have the USB board, PSUs and Drivers in a control box and long leads to the steppers? Thank you.

Cellular telephone base stations are low-powered radiofrequency (RF) transmitters which operate at around 850-900 or 1800-1900 MHz (depending on the technology and region of the world). RF energy in a similar frequency range is used by many other technologies such as microwave ovens, UHF television, other communications systems, and radar. Health and safety issues related to RF energy have been studied for many years and there is an immense literature on the subject. Here are some sources that review health and safety issues related to RF energy from cellular base stations.

A fact sheet published by the World Health Organization. There is also a Spanish version available on the WHO EMF website.
Also see the IEEE EMBS Committee on Man and Radiation Report. Other reports are available through its website.
The International Commission on Nonionizing Radiation Protection (ICNIRP) has published a lot on health and safety of RF energy. See its website. The ICNIRP published an article that describes the ICNIRP exposure limits for RF energy and their scientific rationale. See "Guidelines for Limiting Exposure to Time-Varying Electric, Magnetic, and Electromagnetic Fields (up to 300 GHz)," Health Physics Vol. 74, No 4, pp 494-522, 1998.
A very detailed assessment of the scientific evidence related to health and safety of mobile telephones and base stations is in the recent (May 2000) report by the Independent Expert Group on Mobile Phones (IEGMP) titled "Mobile Phones and Health" This study concludes "the balance of evidence to date suggests that exposures to RF radiation at levels below [international exposure guidelines] do not cause adverse health effects to the general population" but that "there may be biological effects at exposures below those guidelines." Public exposure to RF energy from cellular base stations is invariably far below the ICNIRP exposure guidelines.

Kenneth R. Foster
Professor, Bioengineering
University of Pennsylvania

Click the link to add information to this solution:
I'M SEARCHING FOR INFORMATION ABOUT THE HEALTH RISKS OF CELLULAR ANTENNAS' RADIATION. I NEED SCIENTIFIC (SCIENTIFIC PAPERS IN JOURNALS) THIS.

Do you have the Pokeys57CNC connected to a 24V external power supply?

Additional Information:
Yes, a 24V external power supply with the jumper positioned. I'm using the ethernet port so the 24v is the only source of power. I plan to measure the amp draw when I have a chance to see how much the vfd is drawing on the analog out.

Additional Information:
Further information. The resistance across the terminals on the vfd is 22k ohms. With an independent 0-10v current source I can run the spindle from 20 to 400 Hz. The PokeysCNC only gets to 3.8v with the vfd attached (and the vfd is at 150 Hz) compared to 10v when the vfd is not attached. The power to the PokeysCNC is steady at 24.18 V, so I'm not maxing out the power supply. Still looking for thoughts on what might be going on?

Additional Information:
And the other thing - The measured amperage is 0.17 mA for the 0-10 V signal (which makes perfect sense for 3.7 V and 22k Ohms).

Additional Information:
Just to bring finality to this issue - I added a 2.2 microfarad capacitor across the 0-10V input terminal (from signal to ground). This solved the issue. Evidently, it was an electrical noise issue.

Click the link to add information to this solution:
My pokeysCNC board creates and analog signal of 0-10V for 0 to 24000 spindle rpm just like it should from Mach3. However, when the spindle is on, the voltage only gets to about 3.8V for 24000 rpm. It seems like the vfd is drawing more current than the pokeyscnc analog output can produce. It there an easy solution to this problem?

Currently our USB breakout board is only compatible with Planet-CNC software as it has to be registered with Planet-CNC.

Click the link to add information to this solution:
Hi, I have watched your vids on YouTube and I am interested in purchasing one of your USB Break-Out Boards. I currently own and use FlashCut CNC software, which is USB based, on all of my machines. I'm wondering if you could tell if the Flashcut software will talk with the USB Break-Out Board? Thank You

Not sure what you mean by the statement "I don't know when you answer". Please explain. I answer all of the incoming emails until my inbox is completely empty and all phone calls to the company go straight to my cell phone and I answer all of the calls, and if I don't answer, I call back immediately.


Additional Information:
I just searched my email and found no emails with your email address associated with the email listed with this question. I cannot answer questions if no correspondence was provided by you.

Click the link to add information to this solution:
Please send an email, I am giving up on buying a machine from you because I don't know when you answer. I was asking about getting just the working parts and rails sent to Fiji. You sent an answer and some questions, but I have no way of knowing if you responded again.

We accept many forms of payment, but online, we accept major credit cards (Discover, Visa, MasterCard and American Express) in addition to checking out with Paypal. Depending on what is ordered, a machine vs. a la cart parts, will arrive at your destination according to the shipping method chosen. A machine may take an extra week to be delivered.

Once paid, there are no changes in the amount for the purchase.

Click the link to add information to this solution:
good day I have my list of products in the cart, and before making the purchase need to ask 1. I need to know if I can pay by bank card HSBC Visa 2. If I pay today, As approximate time come to Mexico City? 3. Ordered the shipping information online, and I chose standard UPS. There may be changes in the amount? Thank you

Attaching two motors in parallel is possible, but you will need another motor and driver for the opposite side. Each motor must have its own driver to work accordingly and fluently. The two can be wired together, to the same pins on your breakout board and set the dip switches on the driver to match the ones on your x-axis(ex). But remember to view the orientation of the motor and which way it spins, since it is on the opposite side it will have to be orientated correctly to move in sync with the other motor.

Click the link to add information to this solution:
I just finished building my first CNC with the electronics I purchased from you and I am already thinking about improving it. I would like to build a 2 motor X axis solution. Is it possible to attach 2 parallel motors and drivers to the BlueBrew Breakout Board? If so, how?

You can find the cost of shipping and the delivery times by going to the cart (with the items you intend to purchase) and press calculate shipping. This will give you a list of carriers and their expected delivery times.

If you are purchasing a machine kit or assembled machine, it will take between 2 to 5 weeks. Kits typically take 2 weeks before shipping and assembled machines typically take 5 or more weeks depending on how many machines we are assembling at the moment.

Click the link to add information to this solution:
I would like to ask how long does it take to deliver an item to Egypt? and which shipping company will deliver the item me? and if possible, i'd like to know the total cost of the item and the shipping . . many regards

Here is how to connect your router to the parallel breakout board through the on-board relay. You will need a spare extension cord. You will need to remove a portion of the outer jacket of the extension cord to expose the white, black and green wires (white = neutral, black = live and green = ground), understanding that the neutral and live create the completed circuit.

See this image of a similar connection. The terminal has the same connections.
https://www.buildyourcnc.com/images/vacuum-pressure-controller-relay-terminals-700.JPG

Image of the relay terminal:
https://www.buildyourcnc.com/images/breakoutboardrelayNONC.PNG

The live/black wire would be cut and one end of the cut would be secured into the P terminal and the other cut end would be secured into the S terminal. The live and ground wire would be uncut and travel from the plug to the router.


Additional Information:
You can also connect other high powered devices to the breakout board using any of the output terminals. You will need to supply extra relays like the one shown here:
https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

Or you can find SSRs (Solid State Relays) that will accept 5v to drive the relay coil. Make sure the SSR will protect the 5V line from Back EMF as there is a coil in the relay. The one we sell contains a fly-back diode to protect the 5v terminal.

Click the link to add information to this solution:
I have your breakout board with relay parallel port , I have a vacuum, light on router and air pump I want to also hook up to board, can I hook those up to board and also could I had reylays to each one, what is the best way to figure this out any information would be great. Thanks

If you were logged in when you made the purchase, you can click the "My Account" link at the top of any page on this website and see all of your orders, order line items (with direct links to these items), and shipment information.

Here is a link to the "My Account" page for your convenience:
https://www.buildyourcnc.com/CustomerInfo.aspx

I did not see your username on your internal customer record, so I added this username and you should be able to see the information in the "My Account" page.

Additional Information:
I just tested your accounts page and the cable carrier links are in there. Thanks and please let me know if you need further assistance.

Click the link to add information to this solution:
I have purchased cable carrier chain and would like to know if you could send me a copy of that order as I need to purchase extra lengths of the links I bought. Thanks

The drivers have quite a bit of protection, so you probably won't ruin anything. You motors are jumping and that is just the motors engaging from getting power from the power supply.

There could be many reasons your motors don't turn. Consider these troubleshooting tips:

- If you are using our parallel breakout board, make sure that the step pins are set for active low (config -> Ports and Pins -> Motor Outputs -> the steps pins should be enabled and set active low)

- The parallel breakout board is powered (connect the USB to the computer using a USB cable)

- In Mach3, make sure you have jog enabled (a little green button at thelower middle of the page in the program run screen).

Additional Information:


Additional Information:
DS26

Click the link to add information to this solution:
My stepper motors stopped working all of a sudden. Mach 3 is running fine, just no signals getting to the motors. The lights on the motor drivers began blinking erratically when this started. Any advice where a problem like this can come from would be greatly appreciated.

Yes, you can connect a THC, Torch Height Controller, with the Mach3 USB controller. The THC uses the inputs to determine if the z axis needs to move up or down according to the arc of the plasma torch. The THC connects its outputs to the inputs of the controller so the controller will be informed of the states of the plasma torch.

Click the link to add information to this solution:
I am interested in using the Mach3 USB interface board. I was wondering if there was a way to run a torch height controller with this board for use with a plasma cutter, and if so do you know of any THCs that will work. Thank you.

The connections between the driver and the breakout board(USB/Parallel)22-24 AWG wire is preference also going from the potentiometer going to LSPS(laser power supply) , now going from the power supply to the drivers/laser power supply 16-18 AWG wire is our preference.

Click the link to add information to this solution:
I'm about to order your laser cutter , item 279 and a little confused.. in your faq it states you need wire and connectors for assembly, can you be specific on amount and guage of wire or tell me where to find that information?

Yes, if you have an ordering or shipping issue, please call us during our normal business hours and we will personally look into the issue.

Click the link to add information to this solution:
Hi I have ordered the ARM Microcontroller Beginners Kit (STM32F0) on the 23rd of April but the shipping has still yet to arrive. I did not create an account at the time of purchasing and I am not in the address I provided anymore. May I know how should I go about this problem

The space allotted for the laser tube on the blackTooth would not allow for a higher power laser tube. As the wattage of the laser tube increased, so does the length of the tube.

We do have a larger and more powerful laser in design and should be available in the second quarter of 2015.

Click the link to add information to this solution:
Can you install a more powerful laser/tube for us if we pick the $2100 option to have you build it? It would be assumed that there would be a new price for the machine which would reflect the cost increase for the new laser. Please say yes, I know you can physically do it. I have faith in you

To connect the parallel port breakout board to the LEDs, use step number 18. The connections are listed at the bottom. Here it is for your convenience.

For the LED connections on the parallel breakout board:

- The x axis LED will be connected to pin #2 and 5V
- The y axis LED will be connected to pin #4 and 5V
- The laser on/off LED is connected to pin #6 and 5V

Click the link to add information to this solution:
I can't find any information in the BlackTooth instructions about how to connect the 8 wires from the LED display to the parallel breakout board. The two going to the pot seem, in the illustration, to be soldered together and to the centre terminal of the pot? Help, please.

As shown in the instructions the laser tube that was used was a different model which had the metal end, compared to our full glass tube models we currently ship with the machines.
So there is no difference besides appearance between the two tubes.
The focus lens should be placed in the laser nozzle assembly and not on the laser tube itself.


Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I bought a blacktooth laser from you about a year ago.. I am finally getting around to installing the laser tube and I noticed that my tube does't have the metal end on it like all the pictures I've seen. is this a focus lense and can I purchase one?

It is not clear that mobile phones do produce brain tumors, or any serious health effects for that matter. A number of epidemiology studies have been almost completely negative on the issue.

See the article I wrote with John Moulder in IEEE Spectrum magazine and also Moulder's FAQ on mobile phones and health.

There has been a lot of discussion over the years about the possible mechanisms by which microwave energy such as emitted by cell phones might produce biological effects. The one unequivocal mechanism is the heating of tissue, but mobile phones operate at power levels that are too low to cause noticeable heating in the user. Scientists have speculated about other mechanisms, but these theories remain unproven and many of them have been challenged on biophysical grounds.

Whatever may be the risks or nonrisks of mobile phone radiation, a hands-free kit is an effective way for the user to reduce his or her exposure to radiofrequency energy while using a mobile phone.

Kenneth R. Foster, Professor
Department of Bioengineering
University of Pennsylvania

Click the link to add information to this solution:
I WOULD LIKE TO INQUIRE ABOUT THE PHYSICS PRINCIPLES REGARDING USE OF MOBILE PHONES AND DEVELOPMENT BRAIN TUMORS. I'VE BEEN THROUGH MANY SITES BUT THEY CAN NEVER GIVE AN EXACT ANSWER. REALLY SOMEONE TUMORS OR DOES IT HAVE DO WITH INTENSITY RADIATION DISTANCE BETWEEN PHONE INDIVIDUAL?

I would first check the mechanical parts to ensure smooth motion. Is your machine bogging down during cutting or jogging/rapids?

You can increase the voltage to gain a higher speed for rapids/jogging, but make sure the driver can handle this voltage. There should be a max voltage on the driver label.

If the bogging down is happening during cutting, either reduce the cutting depth or switch out the drive and motor for the axis that is giving the problem.

Click the link to add information to this solution:
[129] I have a Blackfoot and have a question about the power supply. I currently have a 36V power supply and my machine bogs down, would a 70V or something like that help, or will that blow up my machine? thank you!