[59] is it ok to use one pin for all of the limit switches wired NC and another pin for a z probe that is NO, or do all input pins need to be the same (NC or NO)? I would like to use LinuxCNC but will use Mach3 if necessary. a thanks!

Question #: 15425

Question: [Breakout Board with Relay] is it ok to use one pin for all of the limit switches wired NC and another pin for a z probe that is NO, or do all input pins need to be the same (NC or NO)? I would like to use LinuxCNC but will use Mach3 if necessary. a thanks!

Current Solution

It's generally acceptable to use one pin for all of your limit switches wired Normally Closed (NC), and another separate pin for a Z probe that is Normally Open (NO). LinuxCNC is quite flexible and allows for mixed configurations of NC and NO switches.

Just ensure you configure LinuxCNC correctly to recognize each pin's logic (Active low or active high). And perhaps run a few tests before running the machine.

Additional Information:
It's generally acceptable to use one pin for all of your limit switches wired Normally Closed (NC), and another separate pin for a Z probe that is Normally Open (NO). LinuxCNC is quite flexible and allows for mixed configurations of NC and NO switches.

Just ensure you configure LinuxCNC correctly to recognize each pin's logic (Active low or active high). And perhaps run a few tests before running the machine.

Respond:

Other Possible Solutions to this Question

LIMIT SWITCHES FOR AXIS. THE PRINT SHOWS THAT YOU CAN WIRE LIMITS EITHER N.O. OR N.C. SO IF THIS IS CORRECT I WOULD NEED TO TELL BOARD IN SOFTWARE HOW LOOK AT THESE LIMITS, I'M GOING GET AN INPUT LOOSE DEPEND ON IT.
BYCNC Response:
This is correct. You will need to use a method appropriate for the software you are using. Also remember that NC switches are typically wired in series, while NO switches are normally wired in parallel.

User Response:
I am using the cnc planet software for your USB board. Are the limit configurations in this software?

BYCNC Response:
Yes, Planet CNC software is compatible with the use of limit switches. Configuration information will depend on your specific application. You can view Planet CNC's information here: http://www.planet-cnc.com/files/CNCUSBController.pdf
Click the link to add information to this solution:
LIMIT SWITCHES FOR AXIS. THE PRINT SHOWS THAT YOU CAN WIRE LIMITS EITHER N.O. OR N.C. SO IF THIS IS CORRECT I WOULD NEED TO TELL BOARD IN SOFTWARE HOW LOOK AT THESE LIMITS, I'M GOING GET AN INPUT LOOSE DEPEND ON IT.
Additional to Question 3444: Additional Information: To Clarify: I need to set up 3 home switches which can double for limits (that's 3 pins.). Another pin for a probe. That's 4 pins used. Now I need to set up the other limit and E-stop switches. No pins left, how do I do that? Can a ground pin be doubled up on? Plus, I have a SuperPID. Another pin?
You can put all of your limit switches (including the E-stop which serves the same purpose as the limit switches) and home switches on a single pin. When homing, mach3 will move the axis it wants to home, hit the switch, pull away from the switch, then move the next axis and repeat the steps for the next two axes.

The probe is on the 2nd pin. The SuperPID is on the 3rd pin and now you have another pin remaining.

The GND terminal can be doubled up.
Click the link to add information to this solution:
Additional to Question 3444: Additional Information: To Clarify: I need to set up 3 home switches which can double for limits (that's 3 pins.). Another pin for a probe. That's 4 pins used. Now I need to set up the other limit and E-stop switches. No pins left, how do I do that? Can a ground pin be doubled up on? Plus, I have a SuperPID. Another pin?
Limit switches for axis. The print shows that you can wire the limits either n.o. or n.c. so if this is correct I would need to tell the board in the software how to look at these limits, I'm either going to get an input or loose an input depend on how i wire it.
BYCNC Response:
This is correct. You will need to use a method appropriate for the software you are using. Also remember that NC switches are typically wired in series, while NO switches are normally wired in parallel.

User Response:
I am using the cnc planet software for your USB board. Are the limit configurations in this software?

BYCNC Response:
Yes, Planet CNC software is compatible with the use of limit switches. Configuration information will depend on your specific application. You can view Planet CNC's information here: http://www.planet-cnc.com/files/CNCUSBController.pdf
Click the link to add information to this solution:
Limit switches for axis. The print shows that you can wire the limits either n.o. or n.c. so if this is correct I would need to tell the board in the software how to look at these limits, I'm either going to get an input or loose an input depend on how i wire it.
I am attempting to set up limit switches on the 5 axis parallel breakout board that came with my BlackFoot kit. The output pins are driving the motors perfectly, but I can't figure out the input pins. With one lead in the 5V pin and one lead testing the input pins, my multimeter reads 0V for all of the input pins. Shouldn't those circuits be +5V? Where am I going wrong?
When wiring the limit switches to our BoB(breakout board), depending in the older model or our revised version (https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/0/), the older version will need the COM (limit switch) connected to 5V and the NO/NC to your input pin, but with our newer version you will use GND(ground instead of 5V) to common and the same for NO/NC but the setup in the mach3/confi/ports&pins/ is still the same.

Here is a tutorial where you can see how to set up the limit switches correctly (with our older parallel BoB): Part 1:(
), Part 2:(
)
Click the link to add information to this solution:
I am attempting to set up limit switches on the 5 axis parallel breakout board that came with my BlackFoot kit. The output pins are driving the motors perfectly, but I can't figure out the input pins. With one lead in the 5V pin and one lead testing the input pins, my multimeter reads 0V for all of the input pins. Shouldn't those circuits be +5V? Where am I going wrong?
I am converting from a Parallel Port to the Mach3 USB. My limit switches can accomodate up to 5VDC and I want to Drive a Relay from one of the outputs. Will my switches work and do I need a 24VDC Relay?
Yes, the best way to attach a relay to the output of the Mach3 USB board is to use an SSR (Solid State Relay) at the 24 Volt rating. This is the standard supply for this side of the Mach3 USB board.
Click the link to add information to this solution:
I am converting from a Parallel Port to the Mach3 USB. My limit switches can accomodate up to 5VDC and I want to Drive a Relay from one of the outputs. Will my switches work and do I need a 24VDC Relay?
If I wired my stepper motors incorrectly what parts of the electronics will be ruined? When I turn on the power, my motors jump like they are supposed to but for some reason, the G-code doesn't seem to be moving from Mach 3 to the motors. Any help would be appreciated. Do I need to order new electronics or just part of the system? Thanks
The drivers have quite a bit of protection, so you probably won't ruin anything. You motors are jumping and that is just the motors engaging from getting power from the power supply.

There could be many reasons your motors don't turn. Consider these troubleshooting tips:

- If you are using our parallel breakout board, make sure that the step pins are set for active low (config -> Ports and Pins -> Motor Outputs -> the steps pins should be enabled and set active low)

- The parallel breakout board is powered (connect the USB to the computer using a USB cable)

- In Mach3, make sure you have jog enabled (a little green button at thelower middle of the page in the program run screen).

Additional Information:

Additional Information:
DS26
Click the link to add information to this solution:
If I wired my stepper motors incorrectly what parts of the electronics will be ruined? When I turn on the power, my motors jump like they are supposed to but for some reason, the G-code doesn't seem to be moving from Mach 3 to the motors. Any help would be appreciated. Do I need to order new electronics or just part of the system? Thanks
I would like to make a handheld remote for the USB CNC Board using a joystick instead of momentary switches. Could you suggest one that will work with your board.
The USB interface only works with momentary switches unfortunately. If you have extensive knowledge of digital electronics, you can apply a receiver that uses a microcontroller and a transmitter with another microcontroller that produces the pulsing signal with the controls that you need.

Additional Information:

Additional Information:

Additional Information:
Click the link to add information to this solution:
I would like to make a handheld remote for the USB CNC Board using a joystick instead of momentary switches. Could you suggest one that will work with your board.
I have a breakout board and it appears that the pin 12 connection has failed: when i move my limit switches to pin 11 they work; they don't work on pin 12. Do i need a new breakout board?
For safety's sake I would recommend a new board because they are inexpensive compared to the electronics that they support. Alternatively, it's possible that the one dead pin is a simple fix, such as a bad connection or solder joint; if you feel comfortable making those repairs then it could be worthwhile to check. Finally, if you are not using all the input pins, you could continue to operate the limit switch on pin 11 and hope for the best.
Click the link to add information to this solution:
I have a breakout board and it appears that the pin 12 connection has failed: when i move my limit switches to pin 11 they work; they don't work on pin 12. Do i need a new breakout board?
I am building a wet plasma table for my shop that is 8'x 16'. I will need hardware and software. Please heko me wuth the list, My phone is 9124273734. I would like to talk with someone if possible. Thanks, Rus
If you purchase the greenLean, you will get everything you need except a router, computer to operate the machine, and software to control the machine. You state that you have a computer. You can use this computer, but you will need to determine if it has a parallel port, or if you are going to need the USB controller option. As for the software, there are too many different options for you to choose from. We would not be able to tell you which to get, and how much it will cost you. This is a matter of preference. I can tell you, however, that you will need 3 types of software to complete a CNC project. You will need CAD software to design your design, CAM software to add tool paths and convert the design to g-code, and then control software to take the g-code and operate the machine.

Additional Information:
20
Click the link to add information to this solution:
I am building a wet plasma table for my shop that is 8'x 16'. I will need hardware and software. Please heko me wuth the list, My phone is 9124273734. I would like to talk with someone if possible. Thanks, Rus
I am using 5 limit switches on my 3 axis machine. I am using the usb controller for planet cnc. I would like to know where all the wires related to the limit switches get connected? A diagram would be helpful.
The diagram for wiring the USB interface board is located here: https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/

Under the board illustration, there are three smaller diagrams of limit switch wiring. On each, there are two connections, the GND and the pin which are labeled at the ends of the circuit on the diagrams. The pin side would go to the axis label ++ or -- terminal (i.e. X++, or X--). The other end, labeled GND would connect to any ground terminal on the board.
Click the link to add information to this solution:
I am using 5 limit switches on my 3 axis machine. I am using the usb controller for planet cnc. I would like to know where all the wires related to the limit switches get connected? A diagram would be helpful.
I am looking for a controller for a 3 axis dual Y stepper cnc machine. If at all possible I would like a list of the parts that will be needed. I prefer to go with an ethernet setup vs a parallel port.
All of our controller will allow two steppers on any of the axes. Multiple stepper motors and drivers on a single axis is more a function of the way the stepper motor drives are connected to the output pins of the controller. To connect two stepper drivers to a single axis, you need to connect the output pins (dir and step) to each of the two stepper motor drivers.

Consider the controller on cost, features and how they are connected to the computer.

Out lowest cost controllers are:

Mach3 USB board - Has good features and uses the USB from the computer as the main connection
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Parallel Breakout - The computer generates the main signals and this board conditions the signals for the drivers. Although it requires the parallel port from older computer, the board has the most broad compatibility with control software out there including Mach3 and LinuxCNC.
https://buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Highest cost but most feature rich:

Pokey57CNC - works with both Mach3 and Mach4
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board
Click the link to add information to this solution:
I am looking for a controller for a 3 axis dual Y stepper cnc machine. If at all possible I would like a list of the parts that will be needed. I prefer to go with an ethernet setup vs a parallel port.
I have purchased cable carrier chain and would like to know if you could send me a copy of that order as I need to purchase extra lengths of the links I bought. Thanks
If you were logged in when you made the purchase, you can click the "My Account" link at the top of any page on this website and see all of your orders, order line items (with direct links to these items), and shipment information.

Here is a link to the "My Account" page for your convenience:
https://www.buildyourcnc.com/CustomerInfo.aspx

I did not see your username on your internal customer record, so I added this username and you should be able to see the information in the "My Account" page.

Additional Information:
I just tested your accounts page and the cable carrier links are in there. Thanks and please let me know if you need further assistance.
Click the link to add information to this solution:
I have purchased cable carrier chain and would like to know if you could send me a copy of that order as I need to purchase extra lengths of the links I bought. Thanks
I would like to re-order another breakout board, but I would like each output tested beofore shipping. I have recieved a breakout board where the mist coolant doesnt work, and the y-axis sends a 1.5vdc signal voltage. They should all be 5v as you know, or the driver will not read.
If you have received a part that does not work as advertised, or does not function properly, we will ship you a replacement. Please contact customerservice@buildyourcnc.com to make these arrangements.
Click the link to add information to this solution:
I would like to re-order another breakout board, but I would like each output tested beofore shipping. I have recieved a breakout board where the mist coolant doesnt work, and the y-axis sends a 1.5vdc signal voltage. They should all be 5v as you know, or the driver will not read.
I would like to design my own CNC router around one of your electronics bundles, either the 3 Axis - Heavy Gantry or 3 Axis - All Large Motors. Do you have the data sheets for the motors so that I can use the dimensions in my model?
You can find the datasheets to our motors be going to the the stepping motor category page https://www.buildyourcnc.com/category/nema and selecting the motor. This will bring you to the product page for the motor and all of the motor information will be found there.
Click the link to add information to this solution:
I would like to design my own CNC router around one of your electronics bundles, either the 3 Axis - Heavy Gantry or 3 Axis - All Large Motors. Do you have the data sheets for the motors so that I can use the dimensions in my model?
[788] Thanks for the oportunity to ask, I am building a cnc and using npn closed sensors could you help me with the conection of these, do i still connect them in series if i use more than two in each axis. Also you mention that a stop switch should be connected grd and input to the controller would that be done after the 24v power supply. Thanks r
If the sensors are NC (normally closed) you can wire them in series. If the sensors are NO (Normally Open) you can still wire them to the same input, but the wiring needs to be in parallel (like a ladder). I have more information on the following video:
Click the link to add information to this solution:
[788] Thanks for the oportunity to ask, I am building a cnc and using npn closed sensors could you help me with the conection of these, do i still connect them in series if i use more than two in each axis. Also you mention that a stop switch should be connected grd and input to the controller would that be done after the 24v power supply. Thanks r
[311] I am looking to use this type of thing with a pipe for theater. Where the pipe can be lowered and it would have electrical and signal cable inside. Is this good for that or should I look at something else?
This would totally work for that application. This cable carrier is used for any object that needs to move and carries some electrical or tubing within it. This cable carrier is great for cable management where you want to make sure the wires and tubes are in a position that you set, not where the wires and tubing want to go.
Click the link to add information to this solution:
[311] I am looking to use this type of thing with a pipe for theater. Where the pipe can be lowered and it would have electrical and signal cable inside. Is this good for that or should I look at something else?
I am trying to decide which board I should use. I have a wireless MPG and every time I jog Z my X axis steps. If this is not a board issue I would like to go with a wired MPG. So I would like a board that I can have a wired MPG, use a tool touch off probe, control either spindle (VFD) on/off or on/off with speed control, and have homing switches.
A wireless MPG is generally independent of the controller since it communicates to Mach3 directly and does not pass through the controller. I am using a wireless MPG and I have no problems with either of the controllers that I sell (Mach3 USB controller or the Pokeys57CNC controller).

The issue you are having may be in the configuration of the wireless MPG that you are using.
Click the link to add information to this solution:
I am trying to decide which board I should use. I have a wireless MPG and every time I jog Z my X axis steps. If this is not a board issue I would like to go with a wired MPG. So I would like a board that I can have a wired MPG, use a tool touch off probe, control either spindle (VFD) on/off or on/off with speed control, and have homing switches.
I have the 2.2KW VFD. I would like to have it controlled through software. What are the Mode parameters that need to be changed that will allow FWD/ REV, START/STOP and RPM control?
What controller are you using to control the cnc machine (Mach3 usb, parallel breakout board, etc.)?

The spindle VFD has an input for 0-10 volts to control the speed and can be used with the MAch3 USB or the Pokeys57CNC board. There are also other terminals in the VFD to control the forwared/reverse and start and stop. Mach3 has parameters to control these output and you need to specify which pins are used for these.

You can also use the TX/RX RS-485 connection on the VFD to have total control using an FTDI USB to serial connector board to connect the computer directly to the VFD.

How to connect the USB to Serial adapter to the VFD:
https://www.buildyourcnc.com/FAQ/13790

FTDI USB to Serial:
https://www.buildyourcnc.com/item/Interfaces-newbiehack-Interfaces-TTL232R-USB-UART-Serial

Pokeys57CNC board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Mach3 USB board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Parallel Breakout board:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Additional Information:
I do apologize for leaving out the parts list.
Leadshine MX4660 4-Axis Digital Stepper Motor Driver
Ethernet SmoothStepper
YL600-2S-2K20 VFD
4 Relay control board
Has anyone had any success getting Mach3 to control the spindle speed and direction?
Click the link to add information to this solution:
I have the 2.2KW VFD. I would like to have it controlled through software. What are the Mode parameters that need to be changed that will allow FWD/ REV, START/STOP and RPM control?
I already built a 4 x 8ft carving machine, I would like to modify for laser cutting wood. Do you sell a conversion kit? I use Mach3 software and steppers. Thanks Ray
We offer a laser/spindle Z-axis attachment for our 4x8 greenBull CNC. The blackFoot 4x8 does not have a large enough gantry to accommodate the 40W laser tube.

Additional Information:

Additional Information:
We do sell the parts to convert your CNC milling machine to a laser, but you will need to develop the mounts that will hold all of the laser parts to the machine, if the machine was design and built by you.

We can offer guidance for this conversion.

The laser parts can be found here:
https://www.buildyourcnc.com/LaserComponents.aspx
Click the link to add information to this solution:
I already built a 4 x 8ft carving machine, I would like to modify for laser cutting wood. Do you sell a conversion kit? I use Mach3 software and steppers. Thanks Ray