Each home switch needs to be on a separate input on the Mach3 USB controller. For instance, the x-home on IN1, Y-home on IN2, and Z-home on IN3. You can still wire the other switches on the same input, for instance, the IN can contain the X-home and X++ limit. The X, Y, and Z homes can still serve as the limit --.

Additional Information:
So I need 3 of 4 INs only for the home switches??? The remaining one for ++? What about E-Stop and Probe?

Additional Information:
Please have a look at the wiring diagram you show below. There are all limit switches at IN2 and all home switches at IN3. Makes sense to me.

Click the link to add information to this solution:
[575] I have two limit switches for X, Y and Z axes connected to only one input terminal. As usual, I also want to use them as home switches. But after the first axis touches its home switch, I get an emergency stop because of "activating a limit switch". Mach 3 normally knows when to use a limit switch for homing. Which detail in the depths of Mach 3 did I forget?

It seems to be getting some kind of interference or a short within the wiring or communication, try jogging the motors in the software without anything wired to the board. Then add one motor at a time to see if there is a short within your wiring or a faulty driver/motor.
If the USB breakout board continues to move the x-axis with no motors or driver wired to it, please email customerservice@buildyourcnc.com for a replacement or further troubleshooting.

Click the link to add information to this solution:
I am using USB breakout board with planet-cnc software. When I enable jogging keyboard x axis starts to move by itself (whether keyboard connected of not). When I press stop - it stops for a moment and then starts to move again. What could that be? Tried to reinstall software - did not help.

Not a problem. The ALM is rather self-explanatory as this is a closed-loop stepper motor and driver that you are using. The ALM (alarm) is a signal that is used to tell the driver/controller that the motor is not in the same condition that the driver expects. In a closed-loop system, the motor has an encoder that tells the driver exactly how many steps that it turned, and if this value does not coincide with the driver's outputted number of steps, and within a specified amount of time, the alarm will trigger so the system can stop and the workpiece can be salvaged.

The MF is simply a signal that tells the driver that there is impending direction and step pulses coming. If the MF signal is high, then that is similar to an enable signal.

Click the link to add information to this solution:
Hello I recently read your site and have a question. I have a driver model DM2722A but I can't connect it to my usb controller due to the fact that the driver is not marked enable, but instead it is marked: mf-, mf +, alm-, alm +. I will be very grateful if you explain to me the meaning of the latter and tell me what should be related to "enable" Thanks in advance!

It seems to be getting some kind of interference or a short within the wiring or communication, try jogging the motors in the software without anything wired to the board. Then add one motor at a time to see if there is a short within your wiring or a faulty driver/motor.
If the USB breakout board continues to move the x-axis with no motors or driver wired to it, please email customerservice@buildyourcnc.com for a replacement or further troubleshooting.

Click the link to add information to this solution:
I AM USING USB BREAKOUT BOARD WITH PLANET-CNC SOFTWARE. WHEN ENABLE JOGGING KEYBOARD X AXIS STARTS TO MOVE BY ITSELF (WHETHER CONNECTED OF NOT). PRESS STOP - IT STOPS FOR A MOMENT AND THEN AGAIN. WHAT COULD THAT BE? TRIED REINSTALL SOFTWARE DID NOT HELP.

Wiring diagrams for the Laser Power Supply will be mostly the same with the updated power supply. The main difference is the newer power supply contains a secondary green terminal block on the front of the power supply next where the hard leads are connected. This differs from the older power supply which had contact points on the back of the power supply. Please refer to the tutorials section for updated information and if you have specific questions please email techsupport@buildyourcnc.com

Click the link to add information to this solution:
I am assebling the Blacktooth CNC laser 20x24" with what appears to be an updated power supply. After refrencing the wiring diagram on line and the totorial, may I ask for an updated diagram or totorial, the current version do not appear to match match the configuration provided. I do not feel confidant in the educational guess, that I have. thanks

We currently do not have any step down adapters for the vacuum pressure sensor, and would recommend looking at local hardware stores or major online hardware suppliers (ex: McMaster, grainger) . However it is something you will be need to be very specific with, ex: Barb 1/4" Hose ID to 1/8" Hose ID Reducer Fitting. Is something I would recommend when trying to fit a larger tube.

Click the link to add information to this solution:
I am interested in using your vacuum pump controller pressure switch for one of our applications. However, I am concerned about having a proper connection from the 1/16" sensor barb to our vacuum line. Do you carry adapter of common sizes to step down to a 1/16" line? If not, do you know who might? (I have already done some prelim searching with little luck)

I would not recommend slaving an axis using the method of taking an additional axis from the USB interface. Instead, wire both drivers to a single axis on the USB interface. This will insure perfect signal output to both drivers. If you requre the motors to spin in opposite directions, simply wire one of the motors to the driver reversing the coil A and B connections, or use a hex inverter (https://www.buildyourcnc.com/tutorials/Tutorial-Two-Motors-Spinning-Oppositely-On-Single-Axis).

Click the link to add information to this solution:
I purchased a USB Breakout board, motors and drivers, paid for CNC USB Controller Software and I CAN NOT "Slave" an axis, but there is an option to do that. The moment I connect USB Breakout Board "Slave" option becomes shaded and I can no longer select it (becomes not functional). What is going on? Need help asap. Thanks

Yes, you can connect a THC, Torch Height Controller, with the Mach3 USB controller. The THC uses the inputs to determine if the z axis needs to move up or down according to the arc of the plasma torch. The THC connects its outputs to the inputs of the controller so the controller will be informed of the states of the plasma torch.

Click the link to add information to this solution:
I am interested in using the Mach3 USB interface board. I was wondering if there was a way to run a torch height controller with this board for use with a plasma cutter, and if so do you know of any THCs that will work. Thank you.

I would highly recommend a spindle and VFD rather than a router.

Spindles:
- Have a far longer life longer than a router. You will probably go through a few routers before the end of the spindle's life.
- Are quieter than routers
- And the water cooled spindles we stock do not blow the chips into the air. Chips are much easier to capture with or without a dust removal system.

You can find our spindles here:
https://www.buildyourcnc.com/SpindlesAndAccessories.aspx

Once you get your first spindle, you will never go back to routers. Routers are great for handrouting work, but not the best for continuous CNC milling.

Click the link to add information to this solution:
Hi there, I have a cnc table that I built but I am looking for a higher powered router because I am using the table for flattening slabs with a large straight bit. Would you have any recommendations for the type of router I should buy? Also do you sell large bits for flattening slabs?

it is possible to install 2 motors on a single axis but you will require another driver and motor, but wire it directly to the same pins on your breakout board. Also the orientation of your motor since it is opposite side of the original so getting it to move accordingly to the original motor it will need to be orientated correctly. The slight shift could be the cause of the rod not being completely flat where the set screws are suppose to tighten the sprocket to the rod, so sanding it to a flatter surface might fix the shift in directions.
Currently do not have a kit or schematic available.

Click the link to add information to this solution:
Hello, I have a BlackToe 2 x 4 machine. I was wondering if it could be beneficial, or even possible to install two motors on the x-axis (one one each chain drive sprocket). I am noticing a slight shift in the gantry with each reversal of direction. If so, do you have a kit or schematic for this? Thanks

Did you connect the USB connector to the breakout board?

Additional Information:
YES I CONNECTED THE USB TO THE BREAKOUT BOARD

Click the link to add information to this solution:
I connected the electronics (for 2 x 4 feet) that I ordered from you. But how do I check if I connected all the wiring properly. There is neither any light on motor drivers nor on breakout board. And the motor shaft also does not move before and after the power supply is given.

I would suggest using the NPN proximity sensor for the Mach3 USB or the Pokeys57cnc. The proximity sensors have a top DC voltage limit of 30 volts, so it would be best to use the 24V power supply that is used to power the controller. Both controllers have a 24V power requirement, so that is convenient.

The blue wire of the proximity sensor is the GND wire and is connected to the 24V power supply's V- terminal. The brown wire is the positive wire and is connected to the V+ terminal of the 24V power supply. The black wire is the signal wire and is connected to the input terminal of the controller.

Click the link to add information to this solution:
Good evening, if I wanted to use your inductive proximity sensor's with your USB interface board what would I need besides the sensors I would be using 5 of the sensors. I have a 48V 12amp power supply. Thank you

The diagram for wiring the USB interface board is located here: https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/

Under the board illustration, there are three smaller diagrams of limit switch wiring. On each, there are two connections, the GND and the pin which are labeled at the ends of the circuit on the diagrams. The pin side would go to the axis label ++ or -- terminal (i.e. X++, or X--). The other end, labeled GND would connect to any ground terminal on the board.

Click the link to add information to this solution:
I am using 5 limit switches on my 3 axis machine. I am using the usb controller for planet cnc. I would like to know where all the wires related to the limit switches get connected? A diagram would be helpful.

Did you install the Mach3 USB plug-in?

Make sure that you followed all of the steps and diagrams on the following page:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
ABSOLUTELY NOTHING WORKS. I HAVE ALL STRUCTURE AND MECHICAL PARTS OF THE BLACKTOOTH CUTTER DONE. HOWEVER WHEN WIRE UP STEPPER MOTOR TO DRIVER. THAT MACH 3 USB CONTROLLER BOARD, TRY JOG MOTOR, WORKS! PREVIOSULY HAD PLANET CNC BREAKOUT HOWRVER, ONLY MOVED MOTORS IN ONE DIRECTION COULDNT CHANGE IT. ANY HELP WOULD BE APRECIATED

Dealing with our USB BoB, the potentiometer that will be used in the key jog, is a 5V, 5k - 10k Ohm potentiometer.

Click the link to add information to this solution:
I am building a cnc mill using your USB controller and i would like to know what is the specification of potentiometer used for adjusting manual axis jog speed

Sure, our blueChick and blackToe CNC Routers are considered relatively small machines at 1'x3' and 2'x4' respectively. They both use NEMA 23/24 motors. We recommend connecting the machines to either Mach3 or LinuxCNC and come with the necessary interface for either control software. You will need a computer for the control software and if you desire LinuxCNC, you will need a parallel port. Mach3 will accept either parallel port, or USB interface.

Click the link to add information to this solution:
I recently purchased the linksprite cnc engraving router and was wondering if your 3 axis small kit would be ok? the engraver came with nema 17 motors and a arduino board but but not liking the grbl control. could you point me in the right direction .Thanks.

That will depend on the controller that was installed in the redFly. If the controller is a pokeys57CNC controller, you can use Mach 4 with that system.

You can add a 4th axis and an ATC (Automatic Tool Changer) with the redFly system.

Click the link to add information to this solution:
Does the Redfly that I bought with the GreenBull in 2016 work with Mach4? Also I want to add a 4th axis and a spindle with automatic tool changer. Will this work too or do I need a new control board? I bought my CNC with a longer Z travel, so I have plenty of room for these. Thanks!

We apologize for the confusion! The current greenBull kit in the video is a 4' x 8' gB CNC machine, so we currently have a shorter Y-axis length, compared to the 5X/6X kits. However with the gB 5X you should skip every other section(or something similar so it is symmetrical), since we added the option for you to increase the number of ribs if you wish, but is not necessary for the CNC machine.

Click the link to add information to this solution:
Building the 5x10 GreenBull, I went to install the ribs on the mid section of the gantry and you say in the video to skip a spot for the motor to sit, but I have 3 sections that are going to blank not just one like you show in the video. Do I skip more than one, am I missing ribs?

We may be able to source those motors. Curious, the 6000 oz-in motor is pretty big. Do you mind explaining the application of the CNC machine and the structure that would require the large motor?

Additional Information:
The largest motors we can offer is 3900 oz-in without any mechanical help. 6000 oz-in can be resolved by mechanical means as an alternative.

Click the link to add information to this solution:
I am converting a 12x36 lathe over to CNC, I am interested in a 2 axis kit. I would love one stepper motor to be no smaller than 1200oz. , and another at 6000z. Is this something that you could offer? I have two other cnc machines but this is my first converstion on my own.