There is some variation in the outward appearance of laser power supplies due to sourcing through different vendors. However, the basic wiring requirements are the same in each case. For the unit with integrated laser controller, follow the diagram found here: https://buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx#prettyPhoto/0/. The terminals on the signal side will have a 6 connection terminal block -- these are the ones labeled 5V, IN, G, P (or WP), L (or TTL-L), and H (or TTL-H). The High Power side will have 3 inputs for AC power, one high voltage lead, and one return line. Connect these as shown in the diagram as well: the return line goes on the "front" (beam exit end) terminal of the laser tube, the high voltage lead goes to the "back" terminal of the tube, the FG terminal (or G) receives the earth ground wire of the AC power cable, and the two AC terminals receive the line and neutral wires of the AC power cable (it doesn't matter in this case which wire goes to which terminal).

Click the link to add information to this solution:
I purchased the blackTooth Laser Engraver with integrated Laser Control Unit and have been following your instructions. I noticed that the laser tube power supply is different that what is shown in your instructions. Do you have any better wiring guides that I can follow for the version that I received?

The digital signal portion of the CO2 laser tube power supply has various terminals for signal power, signal gnd, laser intensity and engaging the laser (turning it on or off). The TL and TH are triggers to turn the laser power on or off. These may be labeled L or H on some laser power supplies. You can use either TL/L, or TH/H to control the laser.

If you use the TL or L terminal to control the laser:
If a low signal (gnd) is present at that terminal, the laser will turn on. If a high signal (5v) is present, the laser will turn off.

If you use the TH or H terminal to control the laser:
If a high signal (5v) is present at that terminal, the laser will turn on. If a low signal (gnd) is present, the laser will turn off.

You should first test the control signal from the interface with a multimeter to make sure the laser will be controlled correctly before powering the laser power supply

Click the link to add information to this solution:
On the blacktooth machine wiring diagram for parallel breakout a wire goes from 6 on the BOB to TL on the laser power supply. My power supply has an"H" followed by a "L". Which is correct? I've connected to the "L" but the laser appears always on.

I just posted the "enhanced" Blacktooth wiring diagram I developed. Check it out here.

http://www.buildyourtools.com/phpBB3/viewtopic.php?f=12&t=4872

Click the link to add information to this solution:
Where do I wire the ground of my "th" and "power 0v - 5v" command on the power supply ? Is it possible to have a detailed blueprint of the electrical wiring (not for the blacktooth but in general) ? Many thanks :)

Stepper motors are known to make noises while function, however this does not affect accuracy or job function. However we recommend to check your wiring for solid connections, and for good connectivity!



On a personal note, here is one cool video dealing with making songs with stepper motors!

Click the link to add information to this solution:
I bought and built the Blacktooth laser cutter. It works, but one of the stepper motors makes a loud static hiss a second after the CNC power supply is turned on or off, and makes loud tweets and twirps when running. It seems to operate fine otherwise. I was wondering if it was "going bad" or if that is normal?

If the sensors are NC (normally closed) you can wire them in series. If the sensors are NO (Normally Open) you can still wire them to the same input, but the wiring needs to be in parallel (like a ladder). I have more information on the following video:

Click the link to add information to this solution:
[788] Thanks for the oportunity to ask, I am building a cnc and using npn closed sensors could you help me with the conection of these, do i still connect them in series if i use more than two in each axis. Also you mention that a stop switch should be connected grd and input to the controller would that be done after the 24v power supply. Thanks r

The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.

Click the link to add information to this solution:
I bought a 'BuildyourCNC V1' relay board to go with my mach3 usb controller. I have been sent a 'Songle' relay. It's not the one in your picture and it's got different connections, for which there isn't a wiring diagram. The one I ordered says it is 5v, this one seems to be saying it's a 24v unit. Can you please explain what has happened? Thanks

The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.

Click the link to add information to this solution:
I bought a 'BuildyourCNC V1' relay board to go with my mach3 usb controller. I have been sent a 'Songle' relay. It's not the one in your picture and it's got different connections, for which there isn't a wiring diagram. The one I ordered says it is 5v, this one seems to be saying it's a 24v unit. Can you please explain what has happened? Thanks

What laser controller model number do you have?

Additional Information:
Hey - the model number on the laser controller is
AWC708C
S/N:708014243

Additional Information:
Thanks for the model number. I am going to fabricate the parts and put it together myself to see the issue. We made this modification to the blackTooth laser cutter to better house the new laser controller that we wanted to add to the laser, but that may have been for the AWC608. If there is an issue with my assembly, we will create a new part that will correct the issue and send it to you.

Additional Information:
Thank you for the update!

Additional Information:
Have you had a chance to duplicate the issue yet?

Click the link to add information to this solution:
There are no instructions on how to assemble the laser control unit housing that came with my 40w blacktooth laser kit. How can I get instructions for how to assemble the control interface housing? Every configuration I try blocks the wire connection ports.

Yes. The VFD (Variable Frequency Drive) has a large set of parameters that can be modified. This is typically called "programming" the VFD. The parameters can be accessed using the front control panel of the VFD.

Since the VFD is the mechanism that control the allowable current draw from the spindle, there is a parameter that assigns the motor rated current; however, it is probably better to match the rated current of the motor and "up" the circuit breaker current instead. If the current limit is set too low, then there is a possibility that the spindle will cause a current overload error on the VFD and cause the spindle to stop.

Click the link to add information to this solution:
With your 120v drive systems for your 2.2kw spindles, do you do something to limit the output to the spindle so that the current draw doesn't exceed the 80% limitations of a 20a circuit? I have a dedicated circuit for my router and I am considering a spindle upgrade, but I am curious how the configuration matches the math.

The blackTooth laser power supply will use 4 - #8 x 1" screws, and 4 - #8 nuts. As stated on step 10 here (https://buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx#prettyPhoto/10/)

Click the link to add information to this solution:
I am building a blacktooth. I don't see in the instructions what screws are meant to fasten the power supply to the wood. The instructions show how to wire it but I don't see where it says which screws to use. I don't want to guess and end up being short later. Thanks. .

Thanks for your interest in the 80 Watt Laser Tube Power Supply. We will start offering the 220 Volt version of these power supplies on September 23rd.

Additional Information:

Click the link to add information to this solution:
I was looking for a MYJG80W power supply but I see you may not have the 220 volt version. Do you have these as yet and if not what can you advise on availability or where I may find one...Thanks

Many shielded cables come in various materials and designs, so having one with a copper mesh covering the inner insulator wire is no problem. We currently use a extension cord found locally at a hardware store and include one 18G wire for ground. So a specific shielded cable is not a required, unless being used next to specific and sensitive electronics that are extremely sensitive to noise and voltage interference than a shielded cable is required.

Click the link to add information to this solution:
I purchased a 2.2 spindle a while back and went to the electrical supply house to but shielded cable for the power run, I was on the web a while back and saw a picture of shielded cable that didn't look like what I had bought. should it have a copper like mesh wraped around the inner insulation. Thanks

To verify, you are still getting the laser tube to fire, but the laser beam is weak and cannot cut or engrave any materials correct?

Have you checked your tube's tungsten post terminals to make sure they are getting good contact?
The Laser tube and laser power supply both have manufacture warranty, please email customerservice@buildyourcnc.com for further assistance.

Click the link to add information to this solution:
Hello, I have a blacktooth laser cutter, the machine has 10hrs of work, suddenly in the middle of a job the laser beam lost all power, I can still se the purple plasma beam but with no power or intensity, the tube is fine, water is running through and there is no arcing to the chasis or some other part. I think it might be a faulty PS how can I test it, Do I have a warranty on it?

VCC is the same as 5v. I will clarify on the instructions.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
In the BlackTooth instruction the concluding sentence suggests connecting a wire from the right terminal of the pot to the VCC on the Laser Supply. There is no VCC on the power supply for the Laser that I can find. So, does this wire go to a different terminal on the power supply, or somewhere else where VCC exists, such as either stepper motor control?

Your question caused me to make a quick video to understand how the pokeys57CNC controller works with a THC.

Click the link to add information to this solution:
[596] Would you help with the Hook up and the Configuration and whether it is in the Plugin or mach 4 control configuration that needs to be set. I decided to use the ultra fast encoders connector pin #8, 12 and 13 for Arc ok, UP and Down. Please advise what setting to set to make it all work. Thank you very much for your help!

Did you connect the USB connector to the breakout board?

Additional Information:
YES I CONNECTED THE USB TO THE BREAKOUT BOARD

Click the link to add information to this solution:
I connected the electronics (for 2 x 4 feet) that I ordered from you. But how do I check if I connected all the wiring properly. There is neither any light on motor drivers nor on breakout board. And the motor shaft also does not move before and after the power supply is given.

The axis and connection information for the 3D Printer Main Board can be found here in the instructions below the product information.

https://www.buildyourcnc.com/item/3D-Printer-Component-electronicsAndMotors-3d-printer-mainboard-FDMElectronics-3dprintermainboard

Click the link to add information to this solution:
I purchased the driver boards and MB shield for the White Ant. None of the headers are labeled. Is there a diagram showing which headers is for which axis? Is there also a diagram showing which pin on the driver is ABCD? I have watched the vids and the boards in them do not match what was sent to me.

You can test the power supply, but you will need to take extra special care since the voltage on the high tension line can be lethal. Go to this instructable to see all the step on testing the power supply:

http://www.instructables.com/id/How-to-test-and-set-a-Chinese-China-made-CO2-Laser/?ALLSTEPS

Additional Information:

Click the link to add information to this solution:
I am building the Blacktooth laser cutter. What is the safest and most accurate way to test the output of the laser power supply WITHOUT connecting the laser tube? Can I use a standard multimeter and measure the voltage output of the laser power supply?

If you have an existing PC with a parallel port you will not need to purchase the onboard computer system on the blackTooth laser cutter and engraver. You will want to purchase the blackTooth laser engraver that comes with the parallel interface (breakout board). If you have an existing CNC machine that is being used with this PC, you can disconnect the CNC machine and connect the blackTooth to this PC. You will want to have two configurations for your control software.

Additional Information:
We have a version of the blackTooth that is 110v and 220v. We generally determine which is sent according to the requirements of the customer and in what country they live.

Additional Information:
20

Additional Information:
Parallel Port Configuration BIOS settings and Mach 3.

Click the link to add information to this solution:
I'm interested in purchasing your black tooth laser engraver and am curious what setup to get. I already have a cnc wired via parallel port to my PC. Do I need to purchase the black tooth laser with the integrated computer or can I just disconnect my current cnc's parallel port and connect it to the black tooth laser engraver? Also is the black tooth 110v?