Wiring diagrams for the Laser Power Supply will be mostly the same with the updated power supply. The main difference is the newer power supply contains a secondary green terminal block on the front of the power supply next where the hard leads are connected. This differs from the older power supply which had contact points on the back of the power supply. Please refer to the tutorials section for updated information and if you have specific questions please email techsupport@buildyourcnc.com

Click the link to add information to this solution:
I am assebling the Blacktooth CNC laser 20x24" with what appears to be an updated power supply. After refrencing the wiring diagram on line and the totorial, may I ask for an updated diagram or totorial, the current version do not appear to match match the configuration provided. I do not feel confidant in the educational guess, that I have. thanks

There is some variation in the outward appearance of laser power supplies due to sourcing through different vendors. However, the basic wiring requirements are the same in each case. For the unit with integrated laser controller, follow the diagram found here: https://buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx#prettyPhoto/0/. The terminals on the signal side will have a 6 connection terminal block -- these are the ones labeled 5V, IN, G, P (or WP), L (or TTL-L), and H (or TTL-H). The High Power side will have 3 inputs for AC power, one high voltage lead, and one return line. Connect these as shown in the diagram as well: the return line goes on the "front" (beam exit end) terminal of the laser tube, the high voltage lead goes to the "back" terminal of the tube, the FG terminal (or G) receives the earth ground wire of the AC power cable, and the two AC terminals receive the line and neutral wires of the AC power cable (it doesn't matter in this case which wire goes to which terminal).

Click the link to add information to this solution:
I purchased the blackTooth Laser Engraver with integrated Laser Control Unit and have been following your instructions. I noticed that the laser tube power supply is different that what is shown in your instructions. Do you have any better wiring guides that I can follow for the version that I received?

I just posted the "enhanced" Blacktooth wiring diagram I developed. Check it out here.

http://www.buildyourtools.com/phpBB3/viewtopic.php?f=12&t=4872

Click the link to add information to this solution:
Where do I wire the ground of my "th" and "power 0v - 5v" command on the power supply ? Is it possible to have a detailed blueprint of the electrical wiring (not for the blacktooth but in general) ? Many thanks :)

The 12V power supply has 3 terminals for AC in: N, L and earth ground. The output of the 12V power supply has 2 DC + and - terminals. Cut the connectors off of the ends of the fan and pump wires. Strip the red and black wires of both units. The fan will connect to the 12V power supply red to the + and black to the -. The pump will connect in the same way, but the white is not connected.

If you have a pump that has a grey and black wire on the large connector, the grey is the 12VDC V+ wire and the black wire goes to the V-. The extra wire does not need to be connected.

Click the link to add information to this solution:
I purchased the spindle cooling kit with power supply. and was wondering if you have a diagram on installing or a video. thank you

Yes, if you want a laser on the machine, I would highly suggest that the laser be mounted on a separate gantry, similar to the following image:
https://buildyourcnc.com/images/machineConfigurations/greenBullV2_size_04x08_angle_flat_f1_no4thaxis_f2_wilasergantry_f3_nolaser_f4_wilaserready_.png

You would need to develop the gantry structure, but you can use this thread to work out the design with my guidance.

You will need a laser tube, laser power supply, laser controller, mirrors, mirror mounts, lens and nozzle. You will also need some mechanical parts and some motors, drivers and power supplies for the drivers and the controller.

Additional Information:
Yes, if you want a laser on the machine, I would highly suggest that the laser be mounted on a separate gantry, similar to the following image:
https://buildyourcnc.com/images/machineConfigurations/greenBullV2_size_04x08_angle_flat_f1_no4thaxis_f2_wilasergantry_f3_nolaser_f4_wilaserready_.png

You would need to develop the gantry structure, but you can use this thread to work out the design with my guidance.

You will need a laser tube, laser power supply, laser controller, mirrors, mirror mounts, lens and nozzle. You will also need some mechanical parts and some motors, drivers and power supplies for the drivers and the controller.

Click the link to add information to this solution:
I'm interested in getting the CO2 laser & Spindle for my Blackfoot - I currently have just the router mount. Do you sell complete kits or can you advise on what I need? Thank you

Yes, if you want a laser on the machine, I would highly suggest that the laser be mounted on a separate gantry, similar to the following image:
https://buildyourcnc.com/images/machineConfigurations/greenBullV2_size_04x08_angle_flat_f1_no4thaxis_f2_wilasergantry_f3_nolaser_f4_wilaserready_.png

You would need to develop the gantry structure, but you can use this thread to work out the design with my guidance.

You will need a laser tube, laser power supply, laser controller, mirrors, mirror mounts, lens, and nozzle. You will also need some mechanical parts and some motors, drivers, and power supplies for the drivers and the controller.

Click the link to add information to this solution:
I'm interested in getting the CO2 laser & Spindle for my Blackfoot - I currently have just the router mount. Do you sell complete kits or can you advise on what I need? Thank you

I would recommend using a separate 24VDC power supply for the controller. The 24VDC that is connected to the controller is used for delicate input signals and output signals that control external devices. To keep interference and possible current and voltage fluctuations at a minimum due to the motor load, a separate power supply would be best.

Click the link to add information to this solution:
[575] Can the 24VDC supply used for the interface board be the same supply used for stepper drivers, or do you need separate power supplies? If not, does GND and DCM need to be isolated?

The most likely cause of this is a limit switch was triggered, or the limit switch input had a spike in the signal. That can be caused by not using shielded cables for the limit switches. Make sure to disable the limit switches and E-Stop to see if that fixes the problem.

Click the link to add information to this solution:
I was flattining my spoiler board when all of a sudden the machine shut down. Looking at the contollers the geen lights on all three are not on. Thouth it was the power supply. But a new one didn't solve the solutoin.

If your country requires 220 volt peripherals (water pump or air pump) for the blackTooth laser system, then we will either send the 220/240 volt equivalents, or we will have them drop shipped from another location in your country, or a country with compatible power requirements.

Click the link to add information to this solution:
What's the cure for 110 volt pumps (air and water) and a 110volt laser power supply, in a Blacktooth Kit sent to Australia, where 240 volts is pleasingly normal. The fan and other power supply are 220 volts.

The overall size of the machine, really depends on both the area available to you and also the overall size of material being used. Now our larger machines (blackFoot, greenBull, greenLean) can cut all the materials mentioned above, and if equipped with our 2.2kW spindle you will be accurate up to ten thousandths of an inch.
Our greenBull machine does have an option for a long-z axis, that was especially designed to cut foam, but depending on the overall size it might not be a requirement for the specified request.

Click the link to add information to this solution:
I HAVE A SIGN SHOP AND WE NEED CUT ALUMINUM, PLEXIGASS, FOAM AND OTHER MATERIALS FOR SIGNS. CAN YOU TELL ME WHAT MACHINE WE NEED? I LOOKING 4'X8' OR 5' X 10'

When connecting our power supply, no matter if it is 24 or 36 volts with our drivers/motors, you should always use bipolar parallel. This will allow you to have the best torque at higher speeds.

Click the link to add information to this solution:
I have your nema 24 motors using the 36v power supply. Should I use the Bipolar series for the wiring the motors since I am using the 36 volt ad not a 24v power supply?

Many shielded cables come in various materials and designs, so having one with a copper mesh covering the inner insulator wire is no problem. We currently use a extension cord found locally at a hardware store and include one 18G wire for ground. So a specific shielded cable is not a required, unless being used next to specific and sensitive electronics that are extremely sensitive to noise and voltage interference than a shielded cable is required.

Click the link to add information to this solution:
I purchased a 2.2 spindle a while back and went to the electrical supply house to but shielded cable for the power run, I was on the web a while back and saw a picture of shielded cable that didn't look like what I had bought. should it have a copper like mesh wraped around the inner insulation. Thanks

This would totally work for that application. This cable carrier is used for any object that needs to move and carries some electrical or tubing within it. This cable carrier is great for cable management where you want to make sure the wires and tubes are in a position that you set, not where the wires and tubing want to go.

Click the link to add information to this solution:
[311] I am looking to use this type of thing with a pipe for theater. Where the pipe can be lowered and it would have electrical and signal cable inside. Is this good for that or should I look at something else?

That depends on a few factors. In most cases, three 3.0 amp motors and drivers will not exceed 8.8 amps of available current. All of the motors would need to be at full torque to reach the 9 amps (3x3). This depends on the mechanical method you are using for each motor, and how you are using the machine. In most cases, only two motors are moving at a time (i.e. 3D carving where the X and Z are moving simultaneously and the y only moves to go to the next row). In traditional cutting profiles, only the x and y are moving simultaneously and the z-axis moves at the location it needs to start cutting the next layer.

With that said, it is ok to add an extra power supply if you feel you need more available current.

Click the link to add information to this solution:
[810] Is this a closed loop motor? What is the recommended driver and power supply for this stepper? Would you recommend using one power supply per motor pair or one power supply per motor?

Any of the following power supplies will be fine for powering the Mach3 USB controller:
https://www.buildyourcnc.com/item/24v

however, the limit switches do not need high current, so the following power supply is sufficient for the task of connecting limit switches:
https://www.buildyourcnc.com/item/electronicsAndMotors-power-supply-24v-1a-dc

Click the link to add information to this solution:
What power supply do you recommend for the spindle and limit switches if I buy the USB Mach3 breakout board?

All you need is a CNC controller like the following options:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

This controller is easy to connect using standard wire screw terminals and works with the mach3 control software.

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

This controller is a little bit more difficult to connect, but is a more feature-rich controller and will work with both mach3 and mach4 CNC control software titles.

Specifically, a CNC controller connects to the computer via a USB cable and connects to the motor drivers. These controllers also connect to the limit switches, spindle/router control, air/fluid/mist control, etc.

Click the link to add information to this solution:
Hello there, I am a beginner in trying to control a stepper with a pc, you can sell me a kit to control my motor from the pc. I already have a motor, driver, and power supply

We generally use the USB to power the interface (breakout board). The current from the computer is sufficient to supply the breakout board.

Click the link to add information to this solution:
I have a blue brew break-out board. Do I use a seprate power supply for it and what amp output should it have if used.

We generally use the USB to power the interface (breakout board). The current from the computer is sufficient to supply the breakout board.

Click the link to add information to this solution:
I have a blue brew break-out board. Do I use a seprate power supply for it and what amp output should it have if used.

The blackTooth laser power supply will use 4 - #8 x 1" screws, and 4 - #8 nuts. As stated on step 10 here (https://buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx#prettyPhoto/10/)

Click the link to add information to this solution:
I am building a blacktooth. I don't see in the instructions what screws are meant to fasten the power supply to the wood. The instructions show how to wire it but I don't see where it says which screws to use. I don't want to guess and end up being short later. Thanks. .