That is correct. We send the fewer ribs than could be fastened within the gantry. One reduction of a rib will provide more space for the motor at the midpoint of the gantry and at the other side of the gantry (opposite the motor) can be reduced to provide more space to work with the coupling.

Click the link to add information to this solution:
I'm assembling the gantry for a 5x10 greenbull and noticed that there are 9 spaces for torsion spacers but only 7 in the kit. Should I just space them out on the right side behind the motor?

You can find the datasheets to our motors be going to the the stepping motor category page https://www.buildyourcnc.com/category/nema and selecting the motor. This will bring you to the product page for the motor and all of the motor information will be found there.

Click the link to add information to this solution:
I would like to design my own CNC router around one of your electronics bundles, either the 3 Axis - Heavy Gantry or 3 Axis - All Large Motors. Do you have the data sheets for the motors so that I can use the dimensions in my model?

It appears that the LCD that you have on the vacuum pressure controller is damaged. You will need to remove the LCD (desolder the LCD) that is on the controller and resolder a new one.

Here is a link to the LCD used for that vacuum pressure controller:
https://newbiehack.com/categories/newbiehack-LCD_Displays_and_LEDs-LCD-16x2

Newbiehack is a sister website to buildyourcnc.

Click the link to add information to this solution:
I have a vacuum regulator pump controller that I purchased from you previously. The LCD display is now missing the bottom line of text. Have you run into this issue before? Can I just swap out the LCD displays or is a fix going to be more involved?

it is possible to install 2 motors on a single axis but you will require another driver and motor, but wire it directly to the same pins on your breakout board. Also the orientation of your motor since it is opposite side of the original so getting it to move accordingly to the original motor it will need to be orientated correctly. The slight shift could be the cause of the rod not being completely flat where the set screws are suppose to tighten the sprocket to the rod, so sanding it to a flatter surface might fix the shift in directions.
Currently do not have a kit or schematic available.

Click the link to add information to this solution:
Hello, I have a BlackToe 2 x 4 machine. I was wondering if it could be beneficial, or even possible to install two motors on the x-axis (one one each chain drive sprocket). I am noticing a slight shift in the gantry with each reversal of direction. If so, do you have a kit or schematic for this? Thanks

Currently we do not have that modification kit, our set up is fixed for our greenBull only modification kit we have for this model is the long z-axis kit(Designed for Foam cutting).

Click the link to add information to this solution:
I am building your "Green Bull' 6 foot wide kit and I am at the stage of attaching the motor and drive chain. I would like to know if you have an modification kit available to put the 1/2" ACME screw on the Y-axis?

If the sensors are NC (normally closed) you can wire them in series. If the sensors are NO (Normally Open) you can still wire them to the same input, but the wiring needs to be in parallel (like a ladder). I have more information on the following video:

Click the link to add information to this solution:
[788] Thanks for the oportunity to ask, I am building a cnc and using npn closed sensors could you help me with the conection of these, do i still connect them in series if i use more than two in each axis. Also you mention that a stop switch should be connected grd and input to the controller would that be done after the 24v power supply. Thanks r

We may be able to source those motors. Curious, the 6000 oz-in motor is pretty big. Do you mind explaining the application of the CNC machine and the structure that would require the large motor?

Additional Information:
The largest motors we can offer is 3900 oz-in without any mechanical help. 6000 oz-in can be resolved by mechanical means as an alternative.

Click the link to add information to this solution:
I am converting a 12x36 lathe over to CNC, I am interested in a 2 axis kit. I would love one stepper motor to be no smaller than 1200oz. , and another at 6000z. Is this something that you could offer? I have two other cnc machines but this is my first converstion on my own.

If the pdf. files cannot be viewed please update your pdf. reader, also for the X Table End, There are two of these table ends on the machine, each an exact mirror of the other. You will need six (1/4") 2" screws to fasten this to the two table halves. The two holes on either side of the bearing seat require 3" screws to fasten the motor mounts.

For specific requests with needed files (please state email address or email customerservice@buildyourcnc.com)

Click the link to add information to this solution:
I am building the machine frome the book. The measurements for the 6 screws that hold the table together are missing. The chapter seven addisional material on the your website has the measurements but they are unreadable. Can you send me a PDF of that sheet. The cnckit1-1.pdf file on your website also is missing the measurements. Thanks Joe

Hi, this BBB comes with a USB port and its cable to power it up. Once connected to the computer a led in the BBB will light up to show it has power.

Additional Information:
Breakout board I have does not have USB port for the 5v power. Does the parallel port supply the 5V power?

Click the link to add information to this solution:
Hello, we are trying to assemble a kit and the breakout board rev 2.1 that we have does not match the video... we do not see where to connect the 5v powersource to finish step #3, can you provide a location for the power hookup for our board.

The space allotted for the laser tube on the blackTooth would not allow for a higher power laser tube. As the wattage of the laser tube increased, so does the length of the tube.

We do have a larger and more powerful laser in design and should be available in the second quarter of 2015.

Click the link to add information to this solution:
Can you install a more powerful laser/tube for us if we pick the $2100 option to have you build it? It would be assumed that there would be a new price for the machine which would reflect the cost increase for the new laser. Please say yes, I know you can physically do it. I have faith in you

It generally does not matter if it is longer at the other end as long as the lead screw provides the desired travel for that axis. The lead screw will only need to be long enough for the travel, plus any structure and lead-nut positioning.

For example:
- The motor that will turn the lead screw will need to be mounted at some position (generally at one end of the axis). In many cases, this positioning will be mounted where some of the lead screw will not be used (the lead nut will not be able to moved close to the coupling of the lead screw to the motor shaft). Add some of the length of the lead screw to be inserted into the coupling.

- If the lead screw will contain bearings at either end of the travel, that portion of the mechanical assembly will need to be considered in the lead screw length.

- The lead-nut will need to be mounted in a position on a structural member of the part that is to move. The distance from the part of the structure that will extend closest to the motor will have some distance to the position of the lead nut. This distance will need to be added to the lead screw length.

Add these discrepancies to the length of the lead screw and the travel length and you will have the final length.

Click the link to add information to this solution:
How to determine lead screw length needed. My Thomson 1 1:4 rails are 60 inches long roughly for the router I’m building. I know I have to have it long enough to couple up with the stepper motor of course but does it matter if it’s a little long on the other end

Depending on the type of motors and connection type, you could adapt your motors to work with our electronic packages, but you will receive additional motors since our kit is complete.

Now you will have to take into affect the actual motors you have and compare or get accurate replacements(Ex. our 425 oz motor(1/4" input shaft) will have to be same size or similar entry holes)

Your Controller board will be the major issue, due to its wiring and processing manner, you can view the connections for our breakout boards to compare with yours! (parallel: https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/)(USB: https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/)
Email(customerservice@buildyourcnc.com for further help)

Click the link to add information to this solution:
I am looking at one of your electronics packages as a replacement for my excisting electronics. I have a old table top CNC that has a bad electronics pack, but the motors, and the mill are in good shape. could your system be adapted to work in this case?

Can you send me a link to the digitizer you are using?

Click the link to add information to this solution:
Hi my names is Minh Truong I would like to said thank you very much for your video I got the system mach3 working fine but one thing I can NOT set and config the digitizer on the board IN4 I am not sure how to setup because in the Mach3 pin 14 for digitizer Please shoe me hoe to set it up for the digitizer.

This sounds like a problem with the step (pulse) signal. The driver motors receive two signals from the computer via the board -- one is high or low and tells the motors which direction to turn, one is a square wave pulsed signal(quick that tells the motor to turn or a constant high signal that tells the motor to maintain its position. With an oscilliscope you can check for proper signal at the board. If you bought the board from us, please contact us to arrange a return authorization.

Click the link to add information to this solution:
Y axis on usb controller not working. The motor gets power and holds but will not turn. I tried switching the same wires, driver, and motor over to the A axis on the controller and it works fine like that. I have double, and triple checked the wiring

As long as the bearing has a minimum thickness of 1/4" and 9/32" is a bit thicker, there will be no problem with the book build using the bearing that is 1/32" thicker. There is actually more surface area which is better.

Click the link to add information to this solution:
I am building the CNC in your book - Build you own CNC Machine. One of the bearing thicknesses is 1/4" I can't find that bearing online. I can find 9/32, will that be a problem. Do you have a source? Thx

WE don't have an actual file that contains the instructions for the machines as they are a part of a larger database file that is queried during the product page's rendering in the browser. The best option would be to print the webpage on a printer and use that as notes.

I know this will not provide larger images, but you could use the paper version to write your notes while assembling the machine using the larger images on the website.

Click the link to add information to this solution:
On the blackFoot 4'x8' CNC machine do you have the instructions under one file that I can download, I want to print them out and make notes as I am building the machine.

Attaching two motors in parallel is possible, but you will need another motor and driver for the opposite side. Each motor must have its own driver to work accordingly and fluently. The two can be wired together, to the same pins on your breakout board and set the dip switches on the driver to match the ones on your x-axis(ex). But remember to view the orientation of the motor and which way it spins, since it is on the opposite side it will have to be orientated correctly to move in sync with the other motor.

Click the link to add information to this solution:
I just finished building my first CNC with the electronics I purchased from you and I am already thinking about improving it. I would like to build a 2 motor X axis solution. Is it possible to attach 2 parallel motors and drivers to the BlueBrew Breakout Board? If so, how?

The leadscrew length for the greenBull long Z-axis is 47 inches.

Additional Information:

Click the link to add information to this solution:
BUILDING ONE OF YOUR GREENBULL 6X LONG AND 2.2 KILOWATT SPINDLE DOES NOT FIT. SEEMS LEAD SCREW YOU SENT WITH KIT IS SHORT 42" LOOKS LIKE IT NEEDS TO BE 5 OR 6 INCH LONGER. THIS CORRECT? WHAT THE NEEDED LENGTH FOR UNIT?

This is a good video on how to do a vacuum table

Click the link to add information to this solution:
Do you have any videos or plans for how to make a strong table for a large CNC router? I saw the torsion box videos but would like some more guidance on how to build just a good table.