You should have no problem connecting the Pokeys57CNC controller to the drivers of your machine as long as the drivers have step (Pulse or PUL) and direction (DIR) terminals. You will need the cable pack that is sold separately so you can connect the headers/connectors of the pokeys57cnc controller to the drivers using ribbon cables.

I show this process in great detail on this page:
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Is you scroll down on the page, you will see a set of videos that show the process step-by-step.

Click the link to add information to this solution:
I have a ShopBot CNC that was converted to Mach 3. The controller has gone out. I pourchased your Pokeys57 board, but I'm not sure I have everything I need. I think my motor drivers are OK, but am not sure how to wire them to what I purchased from you. Need Help. How can we make this work, or do I need a different board to distribute the movement signals to my drivers?

You can only use the planet-cnc interfaces with the PlanetCNC software. If you like the software and want to remain with that software, the hardware interfaces will need to be purchased from the planet-cnc folks.

I would recommend using the Pokeys57CNC interface which is compatible with Mach3 and Mach4. You can also consider the Mach3 USB interface if the Pokeys57CNc interface is out of your price range.

Pokeys57CNC product page:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Mach3 USB product page:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
I have registered version of planetcnc software that I purchased with a Chinese controller I want to use 3 better drivers with a separate USB controller can you recommend a controller and how to link my existing software. Regards Lloyd from Australia

The relay is only used for devices like routers, spindles, coolant, mist, etc. The relay works like an automatic switch and will allow current to pass when the relay is engaged.

Click the link to add information to this solution:
The relay doesn't have a A+ B - it has signal in god. 5v. / 0 S P. This has to go to my USB motion card wiring shows v+ goes to top of coil no number and comes out the bottom to #2 the relay I got from you is not that simple

Yes, here is the URL for the parallel breakout board that we sell:

https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Click the link to add information to this solution:
can I purchase just the parallel controller board? I purchased the usb option 4 axis combo and would like to also try the system with my parallel port computer. Any help with this will be greatly appreciated; my goal is to implement mach4.

If you want speed control, it is recommended to use the RS-485 connection on the VFD and use the control program such as Mach3 to communication serially with the VFD using this RS-485 connection.

If you would rather use a controller such as the PMDX-107 to simulate the effect of a potentiometer using the Aref, Aout and Agnd and the Rev/Dir and Fwd/Run terminals to control operation and direction, you can connect those to the VFD.

PMDX-107 Aout connects to the VI (analog voltage in). This is like the wiper on a potentiometer.
PMDX-107 Agnd connects to the ACM terminal on the VFD for Analog common.
PMDX-107 COM connects to DCM terminal on the VFD for Digital common.
PMDX-107 Fwd/Run connects to the FOR terminal on the VFD for Forward.
PMDX-107 Rev/Dir connects to the REV terminal on the VFD for Reverse.

Refer to your PMDX-107 manual to correctly configure your dip switch settings and make sure to calibrate (tweak) the speed control using the trimmer next to the terminals on the PMDX-107.

Click the link to add information to this solution:
I purchased the 4.0kw spindle and VFD a while back, and have just installed a PMDX-107 controller... do you have any examples of the wiring connections for the SL-240EE to PMDX-107?

Please email us at customerservice@buildyourcnc.com for replacments/refunds.

However dealing with Autodesk Fusion, did you choose the postprocesser ending with g-code or Mach 3? Using these postprocesser's will work with the planet-cnc program!
Our parallel BoB, with linux-cnc or Mach 3 will work with the arch definition.

Click the link to add information to this solution:
Planet-CNC's USB Controller Software doesn't support the arc definition. Can I get a refund for their hardware I purchased from you? I need something that supports gcode generated by Autodesk Fusion or supports the gcode definition http://linuxcnc.org/docs/html/gcode.html ?

We apologize for the confusion! The current greenBull kit in the video is a 4' x 8' gB CNC machine, so we currently have a shorter Y-axis length, compared to the 5X/6X kits. However with the gB 5X you should skip every other section(or something similar so it is symmetrical), since we added the option for you to increase the number of ribs if you wish, but is not necessary for the CNC machine.

Click the link to add information to this solution:
Building the 5x10 GreenBull, I went to install the ribs on the mid section of the gantry and you say in the video to skip a spot for the motor to sit, but I have 3 sections that are going to blank not just one like you show in the video. Do I skip more than one, am I missing ribs?

Red is A+
Blue is A-
Black is B+
and Green is B-

Click the link to add information to this solution:
I purchased the 3 Axis Heavy Gantry Electronics /w Pokeys57CNC controller and the motors supplied only have 4 wires coming out of them (R,G,B,Blk). Your wiring video shows wiring 8 cables. do you have a video showing how to wire the 4 wire version?

We currently do not have any step down adapters for the vacuum pressure sensor, and would recommend looking at local hardware stores or major online hardware suppliers (ex: McMaster, grainger) . However it is something you will be need to be very specific with, ex: Barb 1/4" Hose ID to 1/8" Hose ID Reducer Fitting. Is something I would recommend when trying to fit a larger tube.

Click the link to add information to this solution:
I am interested in using your vacuum pump controller pressure switch for one of our applications. However, I am concerned about having a proper connection from the 1/16" sensor barb to our vacuum line. Do you carry adapter of common sizes to step down to a 1/16" line? If not, do you know who might? (I have already done some prelim searching with little luck)

I would not recommend slaving an axis using the method of taking an additional axis from the USB interface. Instead, wire both drivers to a single axis on the USB interface. This will insure perfect signal output to both drivers. If you requre the motors to spin in opposite directions, simply wire one of the motors to the driver reversing the coil A and B connections, or use a hex inverter (https://www.buildyourcnc.com/tutorials/Tutorial-Two-Motors-Spinning-Oppositely-On-Single-Axis).

Click the link to add information to this solution:
I purchased a USB Breakout board, motors and drivers, paid for CNC USB Controller Software and I CAN NOT "Slave" an axis, but there is an option to do that. The moment I connect USB Breakout Board "Slave" option becomes shaded and I can no longer select it (becomes not functional). What is going on? Need help asap. Thanks

My apologies for not getting back to you. We always answer the phones during business hours, so I would try that first. Our emails on Monday generally is stacked up as we are closed during the weekend. We can try your g-code here. Please send the g-code to the techsupport@buildyourcnc.com email address and we will test the code to see if it works.

By the way, do you get movement on the planet-cnc UI screen?

Additional Information:
The program starts and runs normal. I have all the correct movement on the mill and the UI screen. Then one of two things happens. It either stops and resets all axis to zero in the middle of the part or it freezes in the middle of the part. When it freezes, it is not moving on the cnc or the UI screen. Sometimes after a freeze it will come up with an 'IO timeout error', but the only way to clear is to unplug USB and start over.
I will send my settings and g-code files over tonight. Please be sure to load my settings when running the g-code. No movement of the cnc is necessary as the controller will do these issues without power to any drives and just the USB board connected, on my board at least.

Click the link to add information to this solution:
I have a MK1 board that I just got running and I am having issues. Do you have an MK1 board at your shop that I can send you my G-Code to run? The freexing/zeroing in the middle of the program issue happens even with no step drives attached to the board.

You want to look for the analog input terminals in the wiring diagram in the manual for your VFD. I believe the VFD you have, the XSY-AT1 has three terminals that will accept an analog voltage to adjust the speed. These terminals are:
COM or ACM - this is where the ACM from the controller will connect
VI/CI - The AVI will connect to this terminal which is the actual voltage level that will determine the speed from 0 to 10V.
10V - This connects to the 10V terminal of the controller which will provide 10V to the controller allowing the top voltage reference for the controller. This will provide a 0 to 10V range for the AVI or VI/CI terminals, and if 5V is available on the VFD, then the range will be 0 to 5V.

The parameter you need to change in the VFD is P10 which will change the source of the frequency, either the control panel which is the default (0 or 1, keys or potentiometer - dial, if that is available on the VFD), External analog signals which are the ACM, VI/CI and 10V/5V terminals in the VFD, or the RS485 which is a serial connection to the computer. You want to set this parameter to the External terminals which may be 2, but check your manual for the proper value.

Click the link to add information to this solution:
I'm hooking up the VFD Controller to the USB controller to control the speed of the spindle. In your video you have the wire from the USB controller to the ACM of the VFD controller. The VFD controller I have is a XSY-AT1 model AT1-2200s. It does not have an ACM contact. It does however have a SP1 contact, is this where I land that wire?

Is this CNC related. If so, what controller are you using?

Additional Information:
I'm using the Mach 3/USB CNC interface board, with the Mach 3 software.

Additional Information:
Does the LED on the controller light up, or blink?

Additional Information:
I believe I've corrected the issue. I found that their are 2 spring like tabs on the female USB port. And take a sharp point like on a compass and gentle raise those tabs a bit. This tighten up the connection, and I never received an error from losing connection.

Click the link to add information to this solution:
It appears I have a connection issue with the USB port on my computer with the USB cord. I purchased a new cord but has the same issue. Is there anything I can do to correct this issue?

Come on over and we will assist you in any way you need.

Click the link to add information to this solution:
I purchased a Blackfoot 4ft X 8ft in 2015 I have yet to run it. Do y’all offer any classes that can help me?? I would very much like to have this machine running. Thank you in Dayton Tx

Yes, you can connect a THC, Torch Height Controller, with the Mach3 USB controller. The THC uses the inputs to determine if the z axis needs to move up or down according to the arc of the plasma torch. The THC connects its outputs to the inputs of the controller so the controller will be informed of the states of the plasma torch.

Click the link to add information to this solution:
I am interested in using the Mach3 USB interface board. I was wondering if there was a way to run a torch height controller with this board for use with a plasma cutter, and if so do you know of any THCs that will work. Thank you.

The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.

Click the link to add information to this solution:
I have your Mach3 usb interface board and am interested in the relay board to turn plasma torch on/off. I have a different relay board that doesn't work, it needs 0/5v from output pin to trigger and the usb board doesn't put out 5 volts. Does this relay board need 5v on output or will work fine with this usb controller?

Is the cable between the mach3 USB and the YL260 shielded. If that does not solve the problem, add an induction coil to the cable to reduce any current fluctuations.

Click the link to add information to this solution:
Hello. I have bought an RnR Motion Controller and a YL260-A and I have it set up to the AVI from RnR to the VI1 of YL620-A but I'm getting that the RPM varies not like interference but like a drop from max value to min value. What could be happening?

You have motors and drivers that already work with your machine (unless the drivers are an all-in-one setup and not modular. I would advise you to keep your current electronics and replace the parallel port breakout board with a controller that uses the USB to operate.

Here are two controllers that work under Mach3, or Mach3 or Mach4:
Mach3 USB controller (works under Mach3 only)
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board
Pokeys57CNC full-featured controller works under Mach3 or Mach4:
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Alternatively, you can purchase a complete plug-and-play system or have your control system sent over to Buildyourcnc to modify the control system to use one of the above controllers.

Click the link to add information to this solution:
[422] I have a probotix cnc router purchased in 2014, used to run on linyx, now Mach3, WindowsXP, printer port, i would like to be able to use a modern computer usb, do you have something like a plug & play or control box i can wire this into, 2 Y axis, i lost my auto tool length when i switched to XP also, any help appreciated

This would totally work for that application. This cable carrier is used for any object that needs to move and carries some electrical or tubing within it. This cable carrier is great for cable management where you want to make sure the wires and tubes are in a position that you set, not where the wires and tubing want to go.

Click the link to add information to this solution:
[311] I am looking to use this type of thing with a pipe for theater. Where the pipe can be lowered and it would have electrical and signal cable inside. Is this good for that or should I look at something else?