The blackFoot uses the same electronics and motors as the blackToe (2'x4') machine. The only parts that change are the gantry horizontal structural parts which may be relatively easy for you to change. We can send you those parts if you are interested in a smaller unit.

Click the link to add information to this solution:
I have a Blackfoot that was purchased in 2017, after the purchase we moved and I haven’t been able to find room for it... would you be interested in buying it back or trading for something smaller. The Blackfoot and computer have never run but I did purchase it assembled. Thanks in advance, scott

Dealing with a larger offset when cutting a larger object, try calibrating your machine accordingly (

Click the link to add information to this solution:
I am having trouble with my cutting precision. I can cut a 1" box within 0.005" accuracy, but when I try to cut something with a 6" profile, it cuts almost 0.125" heavy. Any help would be greatly appreciated.

Yes, here is the URL for the parallel breakout board that we sell:

https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Click the link to add information to this solution:
can I purchase just the parallel controller board? I purchased the usb option 4 axis combo and would like to also try the system with my parallel port computer. Any help with this will be greatly appreciated; my goal is to implement mach4.

Come on over and we will assist you in any way you need.

Click the link to add information to this solution:
I purchased a Blackfoot 4ft X 8ft in 2015 I have yet to run it. Do y’all offer any classes that can help me?? I would very much like to have this machine running. Thank you in Dayton Tx

The drivers have quite a bit of protection, so you probably won't ruin anything. You motors are jumping and that is just the motors engaging from getting power from the power supply.

There could be many reasons your motors don't turn. Consider these troubleshooting tips:

- If you are using our parallel breakout board, make sure that the step pins are set for active low (config -> Ports and Pins -> Motor Outputs -> the steps pins should be enabled and set active low)

- The parallel breakout board is powered (connect the USB to the computer using a USB cable)

- In Mach3, make sure you have jog enabled (a little green button at thelower middle of the page in the program run screen).

Additional Information:


Additional Information:
DS26

Click the link to add information to this solution:
My stepper motors stopped working all of a sudden. Mach 3 is running fine, just no signals getting to the motors. The lights on the motor drivers began blinking erratically when this started. Any advice where a problem like this can come from would be greatly appreciated.

The drivers have quite a bit of protection, so you probably won't ruin anything. You motors are jumping and that is just the motors engaging from getting power from the power supply.

There could be many reasons your motors don't turn. Consider these troubleshooting tips:

- If you are using our parallel breakout board, make sure that the step pins are set for active low (config -> Ports and Pins -> Motor Outputs -> the steps pins should be enabled and set active low)

- The parallel breakout board is powered (connect the USB to the computer using a USB cable)

- In Mach3, make sure you have jog enabled (a little green button at thelower middle of the page in the program run screen).

Additional Information:


Additional Information:
DS26

Click the link to add information to this solution:
If I wired my stepper motors incorrectly what parts of the electronics will be ruined? When I turn on the power, my motors jump like they are supposed to but for some reason, the G-code doesn't seem to be moving from Mach 3 to the motors. Any help would be appreciated. Do I need to order new electronics or just part of the system? Thanks

We may be able to source those motors. Curious, the 6000 oz-in motor is pretty big. Do you mind explaining the application of the CNC machine and the structure that would require the large motor?

Additional Information:
The largest motors we can offer is 3900 oz-in without any mechanical help. 6000 oz-in can be resolved by mechanical means as an alternative.

Click the link to add information to this solution:
I am converting a 12x36 lathe over to CNC, I am interested in a 2 axis kit. I would love one stepper motor to be no smaller than 1200oz. , and another at 6000z. Is this something that you could offer? I have two other cnc machines but this is my first converstion on my own.

The Mach3 USB will not work with Linux CNC. You can use our parallel breakout baord instead (if you have a computer that has a parallel port available).

Here is the link to that interface:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Click the link to add information to this solution:
Hello. I'm currently building my first CNC router, and I'm powering it with a 3 axis electronics kit that was purchased through your site. I chose to get the Mach 3 USB Breakout board, but now I'm wanting to try to use Linux CNC to work with the computer I have available. Will that work with this board?

You should have no problem connecting the Pokeys57CNC controller to the drivers of your machine as long as the drivers have step (Pulse or PUL) and direction (DIR) terminals. You will need the cable pack that is sold separately so you can connect the headers/connectors of the pokeys57cnc controller to the drivers using ribbon cables.

I show this process in great detail on this page:
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Is you scroll down on the page, you will see a set of videos that show the process step-by-step.

Click the link to add information to this solution:
I have a ShopBot CNC that was converted to Mach 3. The controller has gone out. I pourchased your Pokeys57 board, but I'm not sure I have everything I need. I think my motor drivers are OK, but am not sure how to wire them to what I purchased from you. Need Help. How can we make this work, or do I need a different board to distribute the movement signals to my drivers?

We would highly recommend using our forums to sell you machine buildyourtools.com.
We currently do not have a page or option to allow our customers to sell our machines, you can also contact us at customerservice@buildyourcnc.com, for further assistance dealing with the machine and in regards to selling it.

Click the link to add information to this solution:
I have a blueChick 13"x24" or 13"x36" Desktop CNC Router Kit v3.0 (Timing Belt) that I've assembled but never was able to get it running. Can BuildYourCNC assist me in selling this machine? Do you have used machine offerings on your site?

Using Anti-Freeze in the cooling system with either our spindle or our laser tubes will not have any problems and we recommend using a small amount in locations where temperature is freezing or below.
Although we do not recommend using an entire gallon of anti-freeze rather just a small quantity with tap water will be sufficient.

Additional Information:


Additional Information:
All last winter, the temperature was below freezing and sometimes below zero. I used 100% antifreeze for the spindle coolant. Worked great !! All the spindle needs is any type of coolant flowing through it to take the heat away. I use three gallons of antifreeze in a tub with a fish-tank pump to push the antifreeze through. 100% antifreeze works great in cold or hot winter.

Additional Information:
Excellent tip. Thank you for this correction. So it is OK to use antifreeze solely as a cooling method.

Click the link to add information to this solution:
I was wondering what you recommend to use to cool your spindle when continuously exposed to freezing temperature. Can I use winter windshield cleaner (cheap) or do I have to use antifreeze engine coolant or something else? water just sounds like a really bad idea. I live in Canada Eh!

A wireless MPG is generally independent of the controller since it communicates to Mach3 directly and does not pass through the controller. I am using a wireless MPG and I have no problems with either of the controllers that I sell (Mach3 USB controller or the Pokeys57CNC controller).

The issue you are having may be in the configuration of the wireless MPG that you are using.

Click the link to add information to this solution:
I am trying to decide which board I should use. I have a wireless MPG and every time I jog Z my X axis steps. If this is not a board issue I would like to go with a wired MPG. So I would like a board that I can have a wired MPG, use a tool touch off probe, control either spindle (VFD) on/off or on/off with speed control, and have homing switches.

The motor with that model number is here: https://buildyourcnc.com/item/electronicsAndMotors-nema24-425ozin

Click the link to add information to this solution:
In looking for a stepper motor amongst old parts in my lab, I found one with a sticker that says buildyourowncnc.com and PN SM60HT86-2008BF U2 on it. I found a Q&A on your website that says it's a NEMA 24 motor with 425 oz/in holding torque. I was wondering if you were able to confirm this? Any specs sheets and details of the motor would be much appreciated

This video should provide enough guidance to understand the PWM signal on the Mach3 USB controller:

Click the link to add information to this solution:
[575] Hello, I'm wondering if you can provide advice how to wire this USB board where for spindle I would like to use chinese servo motor and driver (TD3) - speed control mode. Especially how to connect - AVI, ACM and 10V (24V is clear). I am still not sure how to power on and off spindle itself. Thank you in advance. Vaclav

The license file should be called Mach1Lic.Dat, you can copy it to a Mach3 folder on another computer and it will register the program.

Click the link to add information to this solution:
You sent my my activation code which I have jealously, guarded on my Desktop till needed, now, unfortunately I cant get it to copy from Desktop to the computer and Mach3, is it possible to get advice on this or maybe a replacement that can be put on a stick then plugged into my Mach3 computer. This is how I have tried but when I open the folder it is empty. Thanks for your patience with me.

You can find the datasheets to our motors be going to the the stepping motor category page https://www.buildyourcnc.com/category/nema and selecting the motor. This will bring you to the product page for the motor and all of the motor information will be found there.

Click the link to add information to this solution:
I would like to design my own CNC router around one of your electronics bundles, either the 3 Axis - Heavy Gantry or 3 Axis - All Large Motors. Do you have the data sheets for the motors so that I can use the dimensions in my model?

You will need to look for the parameter that controls the run frequency. The frequency can be controlled bu the panel, external terminals, or the RS485 TX/RX terminals (UART protocol). You will want to change that parameter so it uses the panel. If you are referring to the maximum panel dial frequency is only allowing 200-300 rpm, then look for the parameters to control the frequency.

For 200 RPM:
Hz = 200/60 = 3.33 Hz

For 300 RPM:
Hz = 300/60 = 5 Hz

Conversion to RPM:
If you ever find yourself yearning to reverse-engineer the process, the formula is as follows:

RPM = Hz × 60

Look for values that match somewhere between 3 and 5 in your frequency parameters and replace them with 400 to give you 24,000 RPM max.

Click the link to add information to this solution:
[77] Hello. I’m interested in buying a water cooled spindle and VFD. I have an Avid Pro CNC and would love to control it using Mach 4 but I keep hearing it’s difficult to integrate. Also, is the water pump 120 or 240? I’d love any advice etc. eBay is a web of confusion with all of the options. Thank you.

Sure, our blueChick and blackToe CNC Routers are considered relatively small machines at 1'x3' and 2'x4' respectively. They both use NEMA 23/24 motors. We recommend connecting the machines to either Mach3 or LinuxCNC and come with the necessary interface for either control software. You will need a computer for the control software and if you desire LinuxCNC, you will need a parallel port. Mach3 will accept either parallel port, or USB interface.

Click the link to add information to this solution:
I recently purchased the linksprite cnc engraving router and was wondering if your 3 axis small kit would be ok? the engraver came with nema 17 motors and a arduino board but but not liking the grbl control. could you point me in the right direction .Thanks.

You will need PlanetCNC software for the USB breakout board and when plugging in the USB the computer should automatically recognize the board, however you can go into device manager to see if the USB terminal is working correctly.
The parallel breakout board; the USB is not a connection terminal rather than a power source, and the parallel port will be the communication terminal.
The items you will need for a water cooled spindle would be: water pump, silicon tubing(length desired by customer), a extension cord(from a hardware store(orange))(1 same gauge wire/length as extension cord).

Click the link to add information to this solution:
I am making my own CNC setup using all the electronics from your website and I have many questions. Please advise how to have my computer recognize the USB connection from my breakout board also I would like to use a water cooled spindle but I need to know the parts required for a 4x10 bed area used for woods and plastics