No, you do not need another motion controller if you have the parallel breakout board and you are using the "Legacy Parallel Port Plug-In" with Mach4. The motion controller is the parallel port.

Click the link to add information to this solution:
I purchased hardware for my plasma table which included 3 nema 34 stepper motors and drivers, power supply,Blue brew BOB, and Mach 4 Control software with parallel port plug-in. In configuring the Mach 4 software it asks for a motion controler. Do I need another device such as a smoothstepper motion controler?

I would not recommend slaving an axis using the method of taking an additional axis from the USB interface. Instead, wire both drivers to a single axis on the USB interface. This will insure perfect signal output to both drivers. If you requre the motors to spin in opposite directions, simply wire one of the motors to the driver reversing the coil A and B connections, or use a hex inverter (https://www.buildyourcnc.com/tutorials/Tutorial-Two-Motors-Spinning-Oppositely-On-Single-Axis).

Click the link to add information to this solution:
I purchased a USB Breakout board, motors and drivers, paid for CNC USB Controller Software and I CAN NOT "Slave" an axis, but there is an option to do that. The moment I connect USB Breakout Board "Slave" option becomes shaded and I can no longer select it (becomes not functional). What is going on? Need help asap. Thanks

Here is the new link to the Planet CNC software download page: http://planet-cnc.com/software/

You can try the software as a demo however you will have limited g-code lines you can run. I believe it was around 500, so you can create small items with the demo.
To fully unlock the Planet-CNC software you will need to purchase the license.

Click the link to add information to this solution:
I purchased the USB BOB and the link for the Planet-cnc software is broke. Will I need to purchase a license for the software as well?

Fusion 360 is a program that allows you to design in a parametric 3 dimensional environment and also provides a great CAM toolset. Fusion 360 will produce the gcode with the CAM capabilities. The gcode is used to move the machine in various ways in order to mill the material; however, software is needed to interpret this gcode and cause the machine to move according to the gcode instructions. This is called control software. So Fusion is CAD/CAM, and you still need "control". Mach3 is one example of control software for milling and is highly recommended.

Install Mach3 onto the computer that will connect to the redFly(CNC electronics), then configure the Mach3 parameters for the machine (motor tuning, plug-ins, inputs/output, etc.). Home the machine, load the gcode into Mach3 and the machine will move according to the gcode.

A word of caution, since you are new to CNC machines, make sure you familiar yourself with the machine and the movements of the machine specific to how the gcode is arranged with respect to the coordinates of the machine. Try with very simple gcode until you get a very good understanding of how the machine will move.

Click the link to add information to this solution:
Hello, My friend has purchased the Redfly and I am helping him a little with it. We are both very new to CNC. I am using fusion 360 at the moment. This can tool path and create gcode. I was wondering if Mach 3 or similar is still needed. Is there a tutorial you could point me to that explains how to get the Gcode from the PC, via Serial to the Redfly?

NC mechanical switch configuration is supported. You can download the manual from this page (Mach4 plugin and manuals):
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

The pokeys57CNC controller has input terminals and pins for limit switches on each of the 8 axes. There are three separate inputs per axis, two for the actual limits of that axis, and one for the home position.

Connect each switch between the GND terminal and its respective axis limit terminal/pin. For instance, the limit switch will typically have three leads, COM, NC, and NO. In an NC configuration, the NC connects to the terminal/pin, say, Axis 1 lim +, and the COM connects to the GND terminal.

In Mach4, in the new device wizard, make sure to specify the correct option on the home and limit switches that matches the machine configuration.



Additional Information:
can you use one switch per axis for home only?

Click the link to add information to this solution:
Hello, I am trying to configure Home and Limit switches using the Pokeyes57cnc and NC switches. I am confused on the procedure of setting this up. wiring to the board and setting up in Mach4. Can you direct me to a tutorial or offer some suggestions? Thanks Dale

When you plug the USB controller into the computer using a USB cable, and the planet-cnc software is running, you will be presented with a dialog box that will contain a text box for the key that you received from the planet-cnc folks.

Additional Information:


Additional Information:
Is there any other software that will work with your controller Mach3? Thanks for the help!

Click the link to add information to this solution:
However it how do I get the software to work? PlanetCNC sent me a key that looks like it will only work with a backup control board I purchased from them?

The steps per unit is automatically determined in the calibration of the axis by clicking on the "set steps per unit" button above the reset button on the settings tab. Initially set the velocity and acceleration to a low setting, like 100 and 10 respectively, so that the axis does not stall during this operation. Once calibrated, the steps per unit will be set to the correct value and the velocity and acceleration can be increased. I have a video explaning the tuning of the motors on this page:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

The name of the video is Test and Tune the motors.

Click the link to add information to this solution:
I purchased the large gantry system with USB control. I have built the CNC and it is working fine. Now fine tuning the motors. On the X-axis I have the Velocity set at 60 (inches), Acceleration at 1.4, the Step Pulse 1-5us and Dir Pulse set at 0. Do I need to adjust the pulses?

What problems are you having?

Click the link to add information to this solution:
I purchased a 4ft X 8ft Blackfoot CNC machine in 2015 and to this date have not been able to use it. How can I get some help. Thank u

That will depend on the controller that was installed in the redFly. If the controller is a pokeys57CNC controller, you can use Mach 4 with that system.

You can add a 4th axis and an ATC (Automatic Tool Changer) with the redFly system.

Click the link to add information to this solution:
Does the Redfly that I bought with the GreenBull in 2016 work with Mach4? Also I want to add a 4th axis and a spindle with automatic tool changer. Will this work too or do I need a new control board? I bought my CNC with a longer Z travel, so I have plenty of room for these. Thanks!

If you were logged in when you made the purchase, you can click the "My Account" link at the top of any page on this website and see all of your orders, order line items (with direct links to these items), and shipment information.

Here is a link to the "My Account" page for your convenience:
https://www.buildyourcnc.com/CustomerInfo.aspx

I did not see your username on your internal customer record, so I added this username and you should be able to see the information in the "My Account" page.

Additional Information:
I just tested your accounts page and the cable carrier links are in there. Thanks and please let me know if you need further assistance.

Click the link to add information to this solution:
I have purchased cable carrier chain and would like to know if you could send me a copy of that order as I need to purchase extra lengths of the links I bought. Thanks

To home the z-axis using a plate:
- Connect the end mill using a large clamping device like an alligator clip with a wire connected to GND.

- Connect the plate (solder a wire to the plate) to one of the input pins.

- You can use the autoset to setup that pin in Mach3 simply by touching the two together once connected to the pin and GND.

Alternatively, the end mill can be connected to the pin and the plate connected to GND as long as there becomes a complete circuit when the end mill touches the plate.

To setup homing for the Planet-CNC homing and limits, go to the Planet-CNC Machine setup page which explains the process step by step: http://www.planet-cnc.com/faq/machine_setup/

Customer Response:
How do I get homing on z to work with planet cnc software using build your own usb board. I have gone to planet website and followed the instructions provided but my software will not allow entries in the required fields they are grayed out is it because I am not using planet-cnc's board, I have used this method for years with Mach3 and would like to use it with the usb board and software.

Answer:
Just received information from the developer. The instructions on how to use a plate for z-axis homing (moveable sensor) can be found here:

http://www.planet-cnc.com/faq/moveable_sensor/

Click the link to add information to this solution:
How do I get Homing on Z to work with Plate and Ground using Buildyourcnc usb board all the entries for the sensor in planet-cnc are grayed out. I am using input z- and I purchased the software

Depending if the spindle can work with this specific VFD, it might be possible. However we would not like to risk you working unit, with a possible match so we would like more details on your specific model and any information available on the spindle itself.

Response
The only info on the spindle is 2.2KW 400HZ 220V. Made by Zhong Hua Jiang.

Was originally on a Delta C200 vfd. That is 220 single phase.

Click the link to add information to this solution:
I PURCHASED A VFD AND SPINDLE FROM FRIEND, HIS SET UP IS 220. DON'T HAVE 220 IN MY SHOP. QUESTION CAN USE YOUR 110 WITH THIS SPINDLE??

Yes, you will need the Mach4 legacy plugin to make the parallel port and Breakout board work.

Click the link to add information to this solution:
Do I use the blue brew BOB that I purchased in conjunction with the Mach 4 PPL Plug-in provided with Mach 4 software when I purchase It?

I have very detailed wiring videos for the Pokeys57CNC controller on the pokeys57CNC controller webpage: https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
[50] I purchased 3 Axis Heavy Gantry Electronics /w Pokeys57CNC controller (Mach3 and 4 Compatible) and Cable Pack I plan to use Mach 3 do You have a wiring diagram Thanks

To stop the laser completely from continuous firing after a job is complete, I recommend to have your file to end while reaching the clearance plane which you will enter in your CAM software. Make sure that your clearance plane value is very small (ex.) 0.001 above 0 and activates at -0.001 also adding a additional g-code manually that raises the z-axis towards the end of the job/run(only if experienced would we recommend using this). This will turn of the laser, rather than the laser staying on and at its current height.

When activating the emergency e-stop, (personal opinion) I would wire the e-stop at the beginning of the live/load wire going to the electronics power supply and the laser power supply.
It will be in at the beginning of the y connection, (https://buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx#prettyPhoto/13/) so you will cut power to both instead of just the CNC electronics.

Click the link to add information to this solution:
Need help configuring Planet CNC software to control laser firing. Currently it is firing using the Z axis but leaves the laser on after a run or when the emergency stop is activated. HELP!!

Is this a licensed version of Mach 3? If not and you are currently running the demo version, mach 3 will have only 500 lines of G-code available for cutting. Which will not allow you to cut or move the machine after the first 500 lines.

Additional Information:
Yes, It is a licensed version of Mach 3.

Click the link to add information to this solution:
Mach 3 stalls in the middle of a file and the dwell button is flashes randomly. Can't control motors and have to re-start Mach 3. Any help?

The USB Interface page: https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout

On this page, there is a datasheet that explains the connection schemes for the limit switches on step 1 of the instructions. The datasheet explains single and multiple switch configurations and parallel/serial connections schemes for the NO/NC (Normally Open/Normally Closed states).

If there is further information you need, please reply on this FAQ.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Please provide detailed instructions on how to connect limit switches to CNC USB BOARD. I can not find instructions anywhere. I am new to cnc world and really need help. Thanks

If you were to buy all of that, only thing you'll need is the mach3 software to run the machine.

Click the link to add information to this solution:
I am interested in purchasing the Green Lean complete kit and also buy the ArtCamPro what other software will I need to up and running?

Come on over and we will assist you in any way you need.

Click the link to add information to this solution:
I purchased a Blackfoot 4ft X 8ft in 2015 I have yet to run it. Do y’all offer any classes that can help me?? I would very much like to have this machine running. Thank you in Dayton Tx