Have you considered reversing the A and B coils on one of the motors to the drivers? This will cause the motor to spin in the opposite direction. This is the easiest method. Using the HEX inverter is a more complex method and not recommended for simple driving tasks.

Click the link to add information to this solution:
I have two nema 34 motors on my gantry and ordered a hex inverter, now I need to wire it correctly. What type of wiring hardware do I need and I will need a wiring diagram also. Please help.

Yes, the redLeaf plug-and-play CNC electronics can include a THC (Torch Height Controller) and motors of any size. The limit of the number of motors that this package can include is 8 motors in total.

Click the link to add information to this solution:
Will the redleaf package allow me to run a torch height controller and 2 nema 34 motors for my gantry? I would prefer to have motors on both sides of the machine with a heavy gantry

To move two stepper motors simultaneously with the same signal, simply wire the two stepper motor drivers to the same interface board signal terminals (CP and CW).

Additional Information:
using a ardino uno controller and a cnc sheild on top of that how to wirer 2 motors to 1 axis its the x axis ?

Click the link to add information to this solution:
I have my motors wired like the wiring diagram I have two motors on Y axis how do I wire the second motor

The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.

Click the link to add information to this solution:
I bought a 'BuildyourCNC V1' relay board to go with my mach3 usb controller. I have been sent a 'Songle' relay. It's not the one in your picture and it's got different connections, for which there isn't a wiring diagram. The one I ordered says it is 5v, this one seems to be saying it's a 24v unit. Can you please explain what has happened? Thanks

The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.

Click the link to add information to this solution:
I bought a 'BuildyourCNC V1' relay board to go with my mach3 usb controller. I have been sent a 'Songle' relay. It's not the one in your picture and it's got different connections, for which there isn't a wiring diagram. The one I ordered says it is 5v, this one seems to be saying it's a 24v unit. Can you please explain what has happened? Thanks

If you want speed control, it is recommended to use the RS-485 connection on the VFD and use the control program such as Mach3 to communication serially with the VFD using this RS-485 connection.

If you would rather use a controller such as the PMDX-107 to simulate the effect of a potentiometer using the Aref, Aout and Agnd and the Rev/Dir and Fwd/Run terminals to control operation and direction, you can connect those to the VFD.

PMDX-107 Aout connects to the VI (analog voltage in). This is like the wiper on a potentiometer.
PMDX-107 Agnd connects to the ACM terminal on the VFD for Analog common.
PMDX-107 COM connects to DCM terminal on the VFD for Digital common.
PMDX-107 Fwd/Run connects to the FOR terminal on the VFD for Forward.
PMDX-107 Rev/Dir connects to the REV terminal on the VFD for Reverse.

Refer to your PMDX-107 manual to correctly configure your dip switch settings and make sure to calibrate (tweak) the speed control using the trimmer next to the terminals on the PMDX-107.

Click the link to add information to this solution:
I have the USB controller board and the 8825 step driver. I need a wiring diagram between the two. Specifically, what does the GND pin on the X-axis connect to? Also, what does the 5V pin on the driver connect to?

You can find a wiring diagram here:
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/

The CP terminal is wired to the step terminal on the 8825 step driver.
The CW terminal is wired to the direction terminal on the 8825 step driver.
The GND terminal connects to the GND on the 8825 step driver

The 5V connector on the driver simply powers the logic side of the chip and needs to connect to VCC pin on the keyboard jog.

Customer Response:
Thanks! Working now.

Click the link to add information to this solution:
I have the USB controller board and the 8825 step driver. I need a wiring diagram between the two. Specifically, what does the GND pin on the X-axis connect to? Also, what does the 5V pin on the driver connect to?

I will send two 8mm to 1/2" couplings to you ASAP. Please send an email to customerservice@buildyourcnc.com so I can determine to whom to send the couings. Thanks.

Additional Information:
Please notice, I followed up with several emails abut this situation. In one, I corrected the motor shaft sizes to 10mm. I understand that, as a result of my emails, the original 1/4" x 1/2" couplers were sent and apparently received by someone at the wrong address. As of this time, I have received no couplers of any size and have gotten no reponses to my emails. Can you enlighten me?

Additional Information:
I looked all throughout my email and I cannot find an email from you. Please send an email to phooddaniel@gmail.com so I can determine who this is and to whom I need to send the new couplings. Thanks

Click the link to add information to this solution:
I ordered two NEMA 23 steppers with 1/4" shafts, I received motors with 8mm shafts. I also ordered two 1/4" x 1/2" couplers, which I have not received. I have no problems with the motors, but I will need couplers to match the 8mm shaft to 1/2" lead screw.

This sounds like a problem with the step (pulse) signal. The driver motors receive two signals from the computer via the board -- one is high or low and tells the motors which direction to turn, one is a square wave pulsed signal(quick that tells the motor to turn or a constant high signal that tells the motor to maintain its position. With an oscilliscope you can check for proper signal at the board. If you bought the board from us, please contact us to arrange a return authorization.

Click the link to add information to this solution:
Have checked stepper motor wires dozens of times and they are wired like diagram says. Stepper motors will not turn under power. I am using laser control option. What should I do?

Red is A+
Blue is A-
Black is B+
and Green is B-

Click the link to add information to this solution:
I purchased the 3 Axis Heavy Gantry Electronics /w Pokeys57CNC controller and the motors supplied only have 4 wires coming out of them (R,G,B,Blk). Your wiring video shows wiring 8 cables. do you have a video showing how to wire the 4 wire version?

I have very detailed wiring videos for the Pokeys57CNC controller on the pokeys57CNC controller webpage: https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
[50] I purchased 3 Axis Heavy Gantry Electronics /w Pokeys57CNC controller (Mach3 and 4 Compatible) and Cable Pack I plan to use Mach 3 do You have a wiring diagram Thanks

can not get the limit switches to work on the usb controller board

Additional Information:
Wiring the motors to the drivers for our 8 wire motor is probably the 425 oz-in NEMA 24 stepping motor. Here is the URL for the diagram of the motor:
https://www.buildyourcnc.com/Documents/PN.SM60HT86-2008BF-U%20(inhouse%20PN.60BYGH303-13)%20(1).pdf

Wire it in bipolar parallel as specified on the data sheet.

Here is the URL for the motor to check if it is the same that you purchased.
https://www.buildyourcnc.com/item/electronicsAndMotors-nema24-425ozin

The USB mach3 board URL is here:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

The wiring diagram is on that page and instruction on how to use it.

Click the link to add information to this solution:
I recently purchased the 3 axis mach3 usb kit the motors have 8 different colored wires (no stripes on wire just solid color) all instructions have different colors. cannot find tutorals. does the mach 3 hook up same as planet? please let me know where I can find wiring diagram to hook up mach 3 usb BOB and motors (I am new to this kind of work projects)

Generally, 3D printers require the following components:

Electronics to move the motors, limit the motion and extrude the filament:
- Stepping motors, one for each axis (X, Y and Z), and one for each extruder

- Stepping motor drivers that are capable of allowing a current draw that matches the stepping motor connected to the driver. https://www.buildyourcnc.com/item/3D-Printer-Component-electronicsAndMotors-stepper-driver-2!5a-FDMElectronics-driver2!5a

- Arduino Mega 2560 to serve as the g-code interpreter. https://www.buildyourcnc.com/item/3D-Printer-Component-electronicsAndMotors-electronic-component-arduino-mega-2560-FDMElectronics

- Arduino shield that breaks out all of the connections from the arduino (3D printer main board). https://www.buildyourcnc.com/item/3D-Printer-Component-electronicsAndMotors-3d-printer-mainboard-FDMElectronics-3dprintermainboard

- Extruder to control the temperature of the hot end (receive temperature readings using a type K thermocouple and send current to the heating cartridge, or power resistor). https://www.buildyourcnc.com/item/3D-Printer-Component-electronicsAndMotors-extruder-controller-FDMElectronics

- End stops to limit the travel of each axis. https://www.buildyourcnc.com/item/3D-Printer-Component-electronicsAndMotors-electronic-component-end-stop-switch-safety-FDMElectronics-endstop

- Type K Thermocople to sense the heat at the hot end. https://www.buildyourcnc.com/item/3D-Printer-Component-typek-thermocouple-heat-sensor-newbiehack-sensors-typek-thermocouple-heat-sensor

- Extruder with motor and hot end. https://www.buildyourcnc.com/item/3D-Printer-Component-extruder

The software to run a 3D printer for our electronics is replicatorG.

Additional Information:
20

Additional Information:

Click the link to add information to this solution:
I am building a big 3d printer using 3 nema 23 and two nema11 for dual head extruder. I need a list of the rest of the stuff I would need including hardware to run these motors and the sofware I would need.

Are you trying to use the MPG (tab), or the keyboard for jogging the motors? You mention 0,0,0, are you trying to home the machine with the "ref all home"?

If you cannot move the motors with the keyboard, check if the jog is enabled.

Click the link to add information to this solution:
[596] I have my motors and limit switches working correctly but I am unable to get any movement from the 'jog step' so that I can set 0,0,0. What should I check

If your Z axis is moving in the opposite direction, go into Mach3, click on config, ports & pins, then click on the motor outputs tab. You will see the axes labeled on the left and the parameters labeled on the top of this dialog box. Toggle the dir low active for the z-axis.

Additional Information:
What if I'm having the same issue on a different axis?

Additional Information:
You can follow the same procedure as with the z-axis. When you get to the motors outputs tab, toggle the dir low active checkbox for the axis that you would like to change.

If you are using another control program, let me know and I will add the recommended action here.

Additional Information:
Girbl

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:
I have a grbl laser machine tronhoo machine that is running back wards and side ways wrong help

Additional Information:

Click the link to add information to this solution:
My Z-axis seems to be reversed on a fully assembled machine... I've tried reversing it in the config settings on Mach 3, but to no avail. What do I need to do? IS this a wiring issue that was not done correctly at the factory?

To move two stepper motors simultaneously with the same signal, simply wire the two stepper motor drivers to the same interface board signal terminals (CP and CW).

Additional Information:
using a ardino uno controller and a cnc sheild on top of that how to wirer 2 motors to 1 axis its the x axis ?

Click the link to add information to this solution:
I need wiring diagram to wire two nema motors parallel

We just received our new inventory of motors and that specific stepper motor ski came back with only one shaft. I’m not at the office to look at this inventory, so if that is true, they will all be single shaft. We may have other stepper motors with included rear shafts, but I will have to see on Monday.

If I don’t have the double shaft, we will provide a refund upon receipt of the motors. My apologies for this error.

Additional Information:
Hi, I'm sending these motors back today. As I understand you, you might have some motors from the previous lot still in stock, and these would be double shaft but otherwise you don't have any and won't be getting any. If you do have two double shaft versions of this motor please send them; if you don't have two of them please let me know--today if possible--so I can start looking elsewhere. Thanks, Ted Armen

Click the link to add information to this solution:
we just received two nema 11 stepper motors per our order--USR2-2, however they are single shaft, we need double shaft, I thought that's what we ordered. We're sending them back, let me know if you do have the double shaft version and I'll try again to order them. I notice the model number on the motor ends in "A", where the packing slip shows "B".

We recommend our electronics combo for the scratch build kit, which you can find on our site here: https://buildyourcnc.com/item/electronicsAndMotors-3axis-425-elcombo. This is our standard general purpose 3 axis electronics system, and includes (3) NEMA 24 425 oz-in stepping motors, (3) Drivers (3.0Amp 24-40 Volts, with 1-1/64 microstepping), (1) 36v 8.8a Power Supply, (1) Interface Board either USB or Parallel. (The USB version requires PlanetCNC software; the parallel interface board gives you a variety of options, Mach3 being one popular choice.)

Click the link to add information to this solution:
I am going to build a CNC 4x4 plasma table. The frame is made of 1 1/4" pipe and the gantry will be made of either 2"x 2" or 2"x 3" tubing. What size stepper motors do you suggest?

Sure, the USB interface has a place for 4 axes of limit switches.

Each axis can have two limit switches: one for the ++ (positive) end and one for the -- (negative) end. The positive end would be the limit switch at the end of the machine that, say the machine has a 4'x8' area, reaches a bit after the 8 foot mark. The negative end would be the limit switch behind the 0 foot location behind the origin. If the origin is in the middle, the negative would be at a little more than the -4 foot end and the positive would be at a bit more than the +4 foot end. Note that you can have more than one switch on each pin where the NC is connected in serial fashion and the NO is connected in parallel fashion (this can be seen on the diagram in the multiple limits switch section). The software configurations for the limits switches are under File -> Settings -> Limit.

A typical limit switch has three connections on it. These connections consist of COM (common), NC (normally closed) and NO (normally open). The COM would generally go to GND and the NC or the NO would go to the pin. If the NC is used, then the the switch is constantly connected until the switch is pushed (engaged) then the connection from the pin to gnd is broken (open). Use the settings in software to set whether in NC or NO configuration.

Let me know if this information was helpful (or not) by adding information to this question. Thanks.

User response:
Thank you very much for this helpful information. I'm still a little fuzzy on how the 6 limit switches physically connect to each other and to the USB breakout board. You've stated one switch (home) goes to positive and another switch (limit) goes to negative. Are all the GND prongs from all 6 switches connected to each other and going to GND on the breakout board, or no? And the NC prongs, how exactly are they connected to each other? And to the board? There has to be a diagram somewhere shows this visually, no? I don't know how to wire the switches in series or in parallel. I have already physically installed all the switches on the machine and ran the wires to where the board is. Now I just need to know where to plug these wires into the board. Also, taking into consideration that I'm using the Planet CNC software, the only settings I have pertaining to limit switches is "Enable/Disable" for each axis, and the actual limit for each axis. Nothing about NC or NO. Is that only in Mach3?
Thank you.

buildyourcnc response:
On the USB interface, the COM on the switch connects to GND and the NC or NO connects to the input pin (i.e. x++, y--, etc.)

Limit switch configuration is rather difficult to understand, especially with series and parallel. You can think of series as a single wire going from GND to the axis letter input terminal (i.e. X++ or X--). If the wire is broken, then the circuit is open (or the switch is engaged in a normally closed scenario). Normally closed is like an actual wire, and when engaged, the switch "opens" (breaks the wire). This is why we recommend in some systems that you can put many switches in series on a single pin. When one of the switches is engaged (breaking the connection) then the entire circuit of switches is broken and the machine stops.

In a parallel scenario, the state of the circuit is always broken until the one of the switches is engaged and the circuit is then closed or connected. The topology looks like a ladder. All the switches connect to both sides of the ladder and the switches are like the runs of the ladder (the horizontal bars that the feet are placed while climbing). Imagine all of the switches broken in this scenario (normally open). It would be like the ladder could be split in two, but if one of the ladder runs (switches) is closed by engaging it, then that run would connect both sides of the ladder and the two sides of the ladder would have a connection.

There is a diagram on the USB page of the various limit switch configurations. If you need more information (visual and/or otherwise), please let us know and we will immediately add that information to benefit everyone.

Click the link to add information to this solution:
I have nearly completed the CNC machine from the book, but I am using it with a USB breakout board, and have no idea how to wire the 6 limit switches to the board. I'm having difficulty following the diagram on the USB breakout board screen. Can someone please help me?