Yes, the 651 oz/in motor requires a driver that is compatible to the motors (the motor will draw 6 amps max and the driver paired with this motor will be able to allow for a 6 amp draw). I would also recommend a 36 volt power supply for better high velocity performance.

Click the link to add information to this solution:
I HAVE ONE OF YOUR SMALLER STEPPER MOTORS RUNNING MY X AXIS BRIDGE CRANE AND IF IT IS MOVED TO FAST THE MOTOR SOUNDS LIKE SKIPPING STEPS WILL 651OZ REQUIRE A DIFFERENT POWER SUPPLY CONTROLER?

Yes, the 651 oz/in motor requires a driver that is compatible to the motors (the motor will draw 6 amps max and the driver paired with this motor will be able to allow for a 6 amp draw). I would also recommend a 36 volt power supply for better high velocity performance.

Click the link to add information to this solution:
I have one of your smaller stepper motors running my X AXIS bridge crane and if it is moved to fast the stepper motor sounds like it is skipping steps will the 651oz stepper motor require a different power supply and controler?

This is most likely a wiring issue. I would disconnect all of the power to the drivers and reconnect one at a time to isolate the problem.

Additional Information:
that was not helpful. I already did that way before submitting this question. there are not that many wires here and I have already rewired this a few times. I actually think its a software or interface board issue because it does work sometimes but then trips (possibly a amperage / voltage issue) I am using the interface board that has a parallel port and usb for 5V. are there different settings that I need to setup?

Click the link to add information to this solution:
I'm using the big 651oz in stepper motor for X and Y and the smaller 325 for the z and X and Y keep tripping when I try to tune the motors on Mach3 but Z seems to work. I have to turn power on and off to reset....is this a wiring issue?

The drivers have quite a bit of protection, so you probably won't ruin anything. You motors are jumping and that is just the motors engaging from getting power from the power supply.

There could be many reasons your motors don't turn. Consider these troubleshooting tips:

- If you are using our parallel breakout board, make sure that the step pins are set for active low (config -> Ports and Pins -> Motor Outputs -> the steps pins should be enabled and set active low)

- The parallel breakout board is powered (connect the USB to the computer using a USB cable)

- In Mach3, make sure you have jog enabled (a little green button at thelower middle of the page in the program run screen).

Additional Information:


Additional Information:
DS26

Click the link to add information to this solution:
If I wired my stepper motors incorrectly what parts of the electronics will be ruined? When I turn on the power, my motors jump like they are supposed to but for some reason, the G-code doesn't seem to be moving from Mach 3 to the motors. Any help would be appreciated. Do I need to order new electronics or just part of the system? Thanks

This sounds like a problem with the step (pulse) signal. The driver motors receive two signals from the computer via the board -- one is high or low and tells the motors which direction to turn, one is a square wave pulsed signal(quick that tells the motor to turn or a constant high signal that tells the motor to maintain its position. With an oscilliscope you can check for proper signal at the board. If you bought the board from us, please contact us to arrange a return authorization.

Click the link to add information to this solution:
Y axis on usb controller not working. The motor gets power and holds but will not turn. I tried switching the same wires, driver, and motor over to the A axis on the controller and it works fine like that. I have double, and triple checked the wiring

We recommend our electronics combo for the scratch build kit, which you can find on our site here: https://buildyourcnc.com/item/electronicsAndMotors-3axis-425-elcombo. This is our standard general purpose 3 axis electronics system, and includes (3) NEMA 24 425 oz-in stepping motors, (3) Drivers (3.0Amp 24-40 Volts, with 1-1/64 microstepping), (1) 36v 8.8a Power Supply, (1) Interface Board either USB or Parallel. (The USB version requires PlanetCNC software; the parallel interface board gives you a variety of options, Mach3 being one popular choice.)

Click the link to add information to this solution:
I got the plans and hardware from you guys and im almost ready for the stepper motor part of this build. what size motors are good to use for this build? the size of cnc will be 2x4 when finish or what size will not work? thanks

All you need is a CNC controller like the following options:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

This controller is easy to connect using standard wire screw terminals and works with the mach3 control software.

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

This controller is a little bit more difficult to connect, but is a more feature-rich controller and will work with both mach3 and mach4 CNC control software titles.

Specifically, a CNC controller connects to the computer via a USB cable and connects to the motor drivers. These controllers also connect to the limit switches, spindle/router control, air/fluid/mist control, etc.

Click the link to add information to this solution:
Hello there, I am a beginner in trying to control a stepper with a pc, you can sell me a kit to control my motor from the pc. I already have a motor, driver, and power supply

When connecting our power supply, no matter if it is 24 or 36 volts with our drivers/motors, you should always use bipolar parallel. This will allow you to have the best torque at higher speeds.

Click the link to add information to this solution:
I have your nema 24 motors using the 36v power supply. Should I use the Bipolar series for the wiring the motors since I am using the 36 volt ad not a 24v power supply?

Have you considered reversing the A and B coils on one of the motors to the drivers? This will cause the motor to spin in the opposite direction. This is the easiest method. Using the HEX inverter is a more complex method and not recommended for simple driving tasks.

Click the link to add information to this solution:
I have two nema 34 motors on my gantry and ordered a hex inverter, now I need to wire it correctly. What type of wiring hardware do I need and I will need a wiring diagram also. Please help.

Have you considered reversing the A and B coils on one of the motors to the drivers? This will cause the motor to spin in the opposite direction. This is the easiest method. Using the HEX inverter is a more complex method and not recommended for simple driving tasks.

Click the link to add information to this solution:
I have two nema 34 motors on my gantry and ordered a hex inverter, now I need to wire it correctly. What type of wiring hardware do I need and I will need a wiring diagram also. Please help.

The blackToe 2'x4' cnc machine is sold as a kit only. We offer plans for the scratch (book) build machine that can be found here for purchase and also comes with a DVD showing the build process: http://www.buildyourcnc.com/cnckitintro.aspx and the plans for build in the book is on the CNC book page: http://www.buildyourcnc.com/Book.aspx.

You can use the same size stepping motors referenced in the book: http://www.buildyourcnc.com/category/elcombo

Click the link to add information to this solution:
I would like to build the 2’x 4’ blackToe2x4v40 CNC router. I have your book. I want to build the latest model blackToe2x4 v40. Are those the correct plans on your web book page ? Is there a bill of materials? If I use a Porter Cable 3-3/4 router motor what size stepper motors do I need?

To move two stepper motors simultaneously with the same signal, simply wire the two stepper motor drivers to the same interface board signal terminals (CP and CW).

Additional Information:
using a ardino uno controller and a cnc sheild on top of that how to wirer 2 motors to 1 axis its the x axis ?

Click the link to add information to this solution:
I have my motors wired like the wiring diagram I have two motors on Y axis how do I wire the second motor

The E.oA.A is an error that the VFD specifies as an overcurrent during ramp up (or acceleration). In other words, the spindle is trying to accelerate to quickly. The spindle cannot handle the inertia during ramp up and it is trying to draw too much current during this process. The best solution that I have researched is to increase the ramp up (acceleration) time, or slow the acceleration. You will need to check which programming setting you need to change, but there will be setting called acceleration time (or ramp up time). Increase this number in small increments until the error goes away. Then, increase it more so there is a safety factor.

Click the link to add information to this solution:
I have the 1.5kW spindle using the 110V vfd which I bought new and has never run correctly for me. The spindle will not accelerate to any reasonable speed before stopping. When it stops, the vfd display reads "E.oA.A". It does not appear to be wiring or settings, I have checked those many times. What else should I look at to troubleshoot this? Is it DOA?

The motors could be wired incorrectly causing them to lock up. Make sure to check the wiring to make sure the X and Y are connected to the correct terminals.

Click the link to add information to this solution:
When Blacktooth is powered on the motors get power but will not turn. What should I do?

We recommend our electronics combo for the scratch build kit, which you can find on our site here: https://buildyourcnc.com/item/electronicsAndMotors-3axis-425-elcombo. This is our standard general purpose 3 axis electronics system, and includes (3) NEMA 24 425 oz-in stepping motors, (3) Drivers (3.0Amp 24-40 Volts, with 1-1/64 microstepping), (1) 36v 8.8a Power Supply, (1) Interface Board either USB or Parallel. (The USB version requires PlanetCNC software; the parallel interface board gives you a variety of options, Mach3 being one popular choice.)

Click the link to add information to this solution:
I am going to build a CNC 4x4 plasma table. The frame is made of 1 1/4" pipe and the gantry will be made of either 2"x 2" or 2"x 3" tubing. What size stepper motors do you suggest?

First, see Jack's build: https://www.buildyourcnc.com/JackRehak.aspx

The difference between mounting the electronics in the gantry is that the connection from the computer (signal level) is long. The alternative, where the electronics is near the computer, the motor cables are long (to reach from the drivers to the motors).

Mounting the breakout board, drivers and power supply within the gantry will cause you to have a long signal connection from the computer to the breakout board. That is fine as long as the cable is long enough, possibly shielded, and can carry the signal at long cable lengths. Make sure to have the cable well away from the motor cables as these will cause quite a bit of interference.

Click the link to add information to this solution:
Provided they will fit and I install a ventilation/cooling fan, is there any reason why I should NOT mount the electronics (breakout board, stepper drivers and power supply) inside the gantry box in my BlackToe 2x4?

It is usually best to mount the motor in a way so it is spinning clockwise to avoid confusion.

Additional Information:
ok, but lets say the motors turn clockwise. if you mount it to ether side of the y axis it will pull to that side so what are the correct positions of the stepper motors. is it the left side or the right side of the y axis and also is it the front or back of the x axis?

Additional Information:
cw250 with mach3 controller

Click the link to add information to this solution:
What side of the x and y axis do you mount the stepper motor to? If it does not matter what side, do I have to change something in mach3?

What controller are you using to control the cnc machine (Mach3 usb, parallel breakout board, etc.)?

The spindle VFD has an input for 0-10 volts to control the speed and can be used with the MAch3 USB or the Pokeys57CNC board. There are also other terminals in the VFD to control the forwared/reverse and start and stop. Mach3 has parameters to control these output and you need to specify which pins are used for these.

You can also use the TX/RX RS-485 connection on the VFD to have total control using an FTDI USB to serial connector board to connect the computer directly to the VFD.

How to connect the USB to Serial adapter to the VFD:
https://www.buildyourcnc.com/FAQ/13790

FTDI USB to Serial:
https://www.buildyourcnc.com/item/Interfaces-newbiehack-Interfaces-TTL232R-USB-UART-Serial

Pokeys57CNC board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Mach3 USB board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Parallel Breakout board:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay



Additional Information:
I do apologize for leaving out the parts list.
Leadshine MX4660 4-Axis Digital Stepper Motor Driver
Ethernet SmoothStepper
YL600-2S-2K20 VFD
4 Relay control board
Has anyone had any success getting Mach3 to control the spindle speed and direction?

Click the link to add information to this solution:
I have the 2.2KW VFD. I would like to have it controlled through software. What are the Mode parameters that need to be changed that will allow FWD/ REV, START/STOP and RPM control?

What is the model number of the laser controller?

Additional Information:
Hey - the model number on the laser controller is
AWC708C
S/N:708014243

Additional Information:
Do you need any additional information here? I really want to get going on it this weekend!

Additional Information:
Sorry about that. If you are referring to the CN1 and CN2 connector, I don't believe it is needed if it didn't come with the connector. The components that we send to the customer is the same package that is sent from the manufacturer of the product. I would try connecting it to the CN1 connector of both units and test the interface (control panel).

Additional Information:
The manual for the AWC 708 shows the two ports CN1 and CN2 connected, but that may just be for thorough documentation if the CN2 is needed for some reason. Do you have a copy of the manual or know where to find it? If not, I will put the document link here.

Click the link to add information to this solution:
my 40w blacktooth laser kit with laser control unit only came with one controller connector, but the unit has two controller ports. Should I have two wires or do I just use controller port number one?