We would highly recommend using our forums to sell you machine buildyourtools.com.
We currently do not have a page or option to allow our customers to sell our machines, you can also contact us at customerservice@buildyourcnc.com, for further assistance dealing with the machine and in regards to selling it.

Click the link to add information to this solution:
I have a blueChick 13"x24" or 13"x36" Desktop CNC Router Kit v3.0 (Timing Belt) that I've assembled but never was able to get it running. Can BuildYourCNC assist me in selling this machine? Do you have used machine offerings on your site?

The greenBull 4X comes with all of the components and electronics to assemble the gantry of the machine. You will need to build the table. We provide the rails and roller chain for the X-axis (along the length of the table for full 8 feet of travel). You will need to provide some wire to connect the electronics and a computer to run the machine. You will also need to purchase the software that you will need to run the machine that matches how you will apply the machine. We suggest the mach3 control program. The CAM program is up to you as there are many options out there.

Click the link to add information to this solution:
I am interested in buying the greenBull 5X Long Z CNC Machine Kit, but it is not clear for me what is included in this kit. Is there anything else I need to get the machine work?

if you purchased the USB interface, you will need planet-cnc software rather than Mach3, and you will need a usb cable to connect the usb interface to the computer.

The blackToe 2x4 CNC Machine Kit with optional table will need wire to connect the electronics. Don't forget to get some end mills to use for cutting the intended material.


Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
If I purchase the [blackToe 2x4 v4.1 CNC Machine Kit - USB Electronics - Table Included] all I would need for this CNC to be fully operational is a laptop with mach 3 software and a router. Is this correct?

The motor is helped by the mechanical leverage of the screw. The 425 oz-in motors that are included in the standard electronics combo has very high torque for that type of machine. You will have no problem using that motor for the book machine.

We use that motor for very heavy spindles on the blackToe and blackFoot CNC Machine kits.

You will need to do the mechanical leverage calculation along with the torque of the motor to determine the actual weight it will lift. The calculation will need to consider the type and pitch of the screw and it would also consider the gravity constant of 9.8 m/s/s.

If you need me to determine this formula and work out the calculation based on the screw you are using, please let me know.

Additional Information:
thank you for the reply. I would be really good to know the calculation. The lead screw is 1/2" diameter with 13 TPI. Please provide the calculation. And one more question. If I am cutting 18mm MDF with 6mm cutting bit (so 6mm pass), what can be the maximum speed rate of cutting and spindle speed of router?
thank you

Click the link to add information to this solution:
I received the electronics for book build cnc machine. I need to know how much weight the z-axis motor can hold since my (craftsman) router seems to be heavy. It is 2HP with variable speed

Have you considered reversing the A and B coils on one of the motors to the drivers? This will cause the motor to spin in the opposite direction. This is the easiest method. Using the HEX inverter is a more complex method and not recommended for simple driving tasks.

Click the link to add information to this solution:
I have two nema 34 motors on my gantry and ordered a hex inverter, now I need to wire it correctly. What type of wiring hardware do I need and I will need a wiring diagram also. Please help.

Have you considered reversing the A and B coils on one of the motors to the drivers? This will cause the motor to spin in the opposite direction. This is the easiest method. Using the HEX inverter is a more complex method and not recommended for simple driving tasks.

Click the link to add information to this solution:
I have two nema 34 motors on my gantry and ordered a hex inverter, now I need to wire it correctly. What type of wiring hardware do I need and I will need a wiring diagram also. Please help.

Decreasing the speed of acceleration in the cutter? Meaning of your router/spindle?, To modify the speed of a router will be going to the router itself and modifying the speed, but if a spindle is being used modifying it will be done either manually in the VFD (VFD Setup:
Change PD001 to '0' (source of run commands)
Change PD003 to 300 (main frequency - Hz)
Change PD004 to 300 (base frequency - Hz)
Change PD005 to 400 (max operating frequency - Hz)
Change PD006 to 2.5 (intermediate frequency - Hz)
Change PD008 to 220 (max voltage - V)
Change PD009 to 15 (intermediate voltage - V)
Change PD010 to 8 (minimum voltage - V)
Change PD011 to 100 (frequency lower limit - Hz)
Change PD142 to 7 (rated motor current - Amps)
Change PD143 to 2 (motor pole number)
Change PD144 to 3000 (rated motor revolution))<- make sure these are your settings in the VFD. If the spindle is wired to the breakout board and is working through Mach 3 then the modification will be done in your CamBam/Feed rate settings.

Click the link to add information to this solution:
How can I decrease the rapid acceleration of the cutter from a completed cutting operation to a new location so that the stepper motor will not lose its steps and mess up the machine zero settings? I am using CamBam and Mach3 on my machine with a chain drive. what is the best way to reduce accleration

Most likely, the driver is not receiving the high or low signal for the direction terminals. The way direction works for an axis is the controller will output a high signal (5V) for one direction and low signal (0V) for the opposite direction. If the signal is always at one signal, say 5V, whether it is commanded in one direction or the other, then the axis will only move in that direction.

To solve this problem, make sure that the wiring is secure at both ends (from the controller to the driver). Also, make sure the Dir+ and DIR- are both wired correctly (i.e. the Dir- is connected to the signal gnd on the controller and the ZD is connected to Dir+ on the driver.

You can use a multimeter to determine the voltage at the ZD terminal by:
- setting the multimeter to DC voltage (the V with a straight line, or dashed line above the V)
- place the black lead on the gnd terminal
- place the red lead on the ZD terminal
- press the page up button and check the voltage
- press the page down button and check the voltage.

You should see the voltage change from 0V to 5V or vice versa.

Click the link to add information to this solution:
Hi I have just set up my machine using a mach 3 USB board I can only get the Z to go in one direction Y and X are Ok I have check wiring and looked at video over and over what have I missed??

The relay is only used for devices like routers, spindles, coolant, mist, etc. The relay works like an automatic switch and will allow current to pass when the relay is engaged.

Click the link to add information to this solution:
The relay doesn't have a A+ B - it has signal in god. 5v. / 0 S P. This has to go to my USB motion card wiring shows v+ goes to top of coil no number and comes out the bottom to #2 the relay I got from you is not that simple

Can you provide the model number of your VFD?

Yes, I have the "YL600 - 2S - 2K20"

It just came with a small booklet that is all in Chinese...

Click the link to add information to this solution:
I WIRED MY VFD (2.2KW VERSION) AND TRIED TEST RUNNING THE SPINDLE. CONFIGURED TO YOUR SPECS ON THIS WEBSITE, ONLY ISSUE IS WE GOT AN ERROR CODE. ERR 02, DO YOU KNOW WHAT IS? OR HAVE A LIST OF CODES? THANK

This is most likely a wiring issue. I would disconnect all of the power to the drivers and reconnect one at a time to isolate the problem.

Additional Information:
that was not helpful. I already did that way before submitting this question. there are not that many wires here and I have already rewired this a few times. I actually think its a software or interface board issue because it does work sometimes but then trips (possibly a amperage / voltage issue) I am using the interface board that has a parallel port and usb for 5V. are there different settings that I need to setup?

Click the link to add information to this solution:
I'm using the big 651oz in stepper motor for X and Y and the smaller 325 for the z and X and Y keep tripping when I try to tune the motors on Mach3 but Z seems to work. I have to turn power on and off to reset....is this a wiring issue?

Can you provide the model number of your VFD?

Yes, I have the "YL600 - 2S - 2K20"

It just came with a small booklet that is all in Chinese...

Click the link to add information to this solution:
I wired my vfd (2.2kw version) and tried test running the spindle. I configured to your specs on this website, only issue is we got an error code. Err 02, do you know what this is? OR have a list of error codes? Thank you

CamBam specifically creates the g-code (machining operations) instructions to be loaded into Mach3. Make sure in your CamBam g-code file parameters, you are using the Mach3 post processor. If you have already done this, let me know. If you are not sure how to do this, let me know.

Click the link to add information to this solution:
I am having trouble connecting the cambam program with my Mach3 to my 4X8 Blackfoot CNC machine. Where can I get help on this issue. Have had my machine since 2015 and have not been able to use it. Thank you

The 5x10 greenBull base kit comes with the structure, hardware, and electronics for motion control. In order to have a fully functional CNC you will need a table base for your machine, a spindle or router to handle your cutting applications, end mills (bits) for cutting, CAD, CAM and CNC software, and a computer. There are also accessories you can add such as limit switches, emergency stops, and cable carrier for cable management. If you are looking for more information or a formal quote please contact sales@buildyoucnc.com

Click the link to add information to this solution:
I'm not sure of ALL the things I will need to do some of my ideas for the cnc machine. I'll mostly be cutting out 3/4" plywood projects. How much minimum for a 5' by 10' system? I need the hardware and software to get the job done. I saw the price for your basic unit 3-4 grand but don't know what all I NEED to start work.

The E.oA.A is an error that the VFD specifies as an overcurrent during ramp up (or acceleration). In other words, the spindle is trying to accelerate to quickly. The spindle cannot handle the inertia during ramp up and it is trying to draw too much current during this process. The best solution that I have researched is to increase the ramp up (acceleration) time, or slow the acceleration. You will need to check which programming setting you need to change, but there will be setting called acceleration time (or ramp up time). Increase this number in small increments until the error goes away. Then, increase it more so there is a safety factor.

Click the link to add information to this solution:
I have the 1.5kW spindle using the 110V vfd which I bought new and has never run correctly for me. The spindle will not accelerate to any reasonable speed before stopping. When it stops, the vfd display reads "E.oA.A". It does not appear to be wiring or settings, I have checked those many times. What else should I look at to troubleshoot this? Is it DOA?

The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.

Click the link to add information to this solution:
I bought a 'BuildyourCNC V1' relay board to go with my mach3 usb controller. I have been sent a 'Songle' relay. It's not the one in your picture and it's got different connections, for which there isn't a wiring diagram. The one I ordered says it is 5v, this one seems to be saying it's a 24v unit. Can you please explain what has happened? Thanks

The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.

Click the link to add information to this solution:
I bought a 'BuildyourCNC V1' relay board to go with my mach3 usb controller. I have been sent a 'Songle' relay. It's not the one in your picture and it's got different connections, for which there isn't a wiring diagram. The one I ordered says it is 5v, this one seems to be saying it's a 24v unit. Can you please explain what has happened? Thanks

Yes, we can help you with leveling your CNC machine even if you didn't purchase it from us.

Click the link to add information to this solution:
[789] I need to level my cnc machine, but I didn't purchase it from you, so: Do you offer tech support with leveling a cnc? Because I don't see this problem listed .And: Do you offer support if my machine was purchased in China or from another vendor?

Modifying the Z-axis to accommodate a larger motor will be a worth while task and is possible, however we have not calibrated the z-axis therefore using the 1600 Steps-per inch in the motor tuning on our machine in our shop. We have not noticed any significant depth increments from not calibrating the z-axis but only from zeroing the z axis too close to the material. Also in your design did you specify the actual depth and the length of tool (end mill/ bit) that you are using?

Click the link to add information to this solution:
I bought a Blacktoe 2 x 8 three years ago and have always had a problem with the Zid axis. No matter how tightly I've calibrated the axis it always cuts to deep. Can I put a larger Stepper motor on Z-axis using the same motion electronics that came with the original machine.