We recommend our electronics combo for the scratch build kit, which you can find on our site here: https://buildyourcnc.com/item/electronicsAndMotors-3axis-425-elcombo. This is our standard general purpose 3 axis electronics system, and includes (3) NEMA 24 425 oz-in stepping motors, (3) Drivers (3.0Amp 24-40 Volts, with 1-1/64 microstepping), (1) 36v 8.8a Power Supply, (1) Interface Board either USB or Parallel. (The USB version requires PlanetCNC software; the parallel interface board gives you a variety of options, Mach3 being one popular choice.)

Click the link to add information to this solution:
I am going to build a CNC 4x4 plasma table. The frame is made of 1 1/4" pipe and the gantry will be made of either 2"x 2" or 2"x 3" tubing. What size stepper motors do you suggest?

What electronics do you have at the moment? Depending on your machine, you will need a minimum of 3 stepper motors and 3 drivers (unless your heavy axis requires two stepper motors and two drivers). You will also need an interface board that is capable of providing three inputs for the THC (Torch Height Controller), THC on, THC up and THC down, and outputs for firing the torch. I would recommend the Pokeys57CNC interface for the primary interface. This interface will connect to the stepper motor drivers and the THC. The Pokeys57CNC can also communicate via USB or Ethernet.

Click the link to add information to this solution:
Looking for electronics for a plasmacam table. It's going to to be a 5'x10' table with x,y,z axis. Will be running on windows ten with a hypertherm powermax45 xp plasma cutter. Any information or links would be greatly appreciated!

Absolutely, I can answer this type of question and anything other questions you may have with your new-to-you CNC router.

Additional Information:
20

Click the link to add information to this solution:
[789] Can you help me with selecting a power supply ( and a few other components ) for the stepper motors that came with a homemade CNC Router I just purchased.

We currently do not sell any plan's for any of our machines, only for our scratch and build kit.

Click the link to add information to this solution:
Would you sell a kit that has all of the hardware and electronics with CNC plans for the table and gantry? Some of have access to a CNC temporarily (TechShop) but want one of our own.

The bluchick CNC router is a perfect small format CNC that can handle most jobs. Please check here to see the latest information on this CNC router. blueChick CNC Machine. The machine can be purchased assembled. Al you will need is a computer and spindle.

Click the link to add information to this solution:
I'm looking for a complete CNC router, out the box ready to use system. Computer and software. What do you suggest? I need a working area of 12"x24"

We carry several sizes of lead screw and stepper motors on our website, for example here https://buildyourcnc.com/Item/mechanical-leadscrews-lead-screw-!5-5-starts-10-tpi and here https://buildyourcnc.com/ProductSearchResults.aspx. Please call us at 281-815-7701 to discuss the particular lengths you would need and shipping options.

Additional Information:
https://buildyourcnc.com/ProductSearchResults.aspx is not working

Additional Information:



Additional Information:

Click the link to add information to this solution:
I have a project very similar to cnc machine. I need 3 lead screws of 1.8 m with all set (supports, bearings...etc). and 3 NEMA 42 motors that I can connect with. if those are available, I need the information about shipping to Oman or UAE.

Actual table dimension: 4'x8' is 56.078"x 121.50" (the overhang in the illustrations should be 3/4" thick)
To determine the frame dimensions, first consider using the frame height shown of almost 3' (2.86'). The width of the frame should be 4" narrower than the dimension from rail edge to rail edge (6X rail to rail is 80.078"). This will provide a 2" overhang on both sides (4X frame width should be 56.078").
The length of the frame should be 4" shorter than the desired length of the rails to provide a 2" overhang on both ends. The travel length will be 20" shorter than the rail length due to the space occupied by the gantry sides.
Two long pieces of 3/4" material will need to be placed on top of the frame with the 2" overhang on the sides and the end. These long strips of material will receive the rails and the chain mounts on the ends.


Link:
https://www.buildyourcnc.com/Item/cnc-machine-greenBull-v4-4X

Click the link to add information to this solution:
I have just purchased a 4x8 Greenbull system second-hand. Are there any schematics for table dimensions and rail-mounting available so that I can build a table? (previous owner disassembled)

Yes, the redLeaf plug-and-play CNC electronics can include a THC (Torch Height Controller) and motors of any size. The limit of the number of motors that this package can include is 8 motors in total.

Click the link to add information to this solution:
Will the redleaf package allow me to run a torch height controller and 2 nema 34 motors for my gantry? I would prefer to have motors on both sides of the machine with a heavy gantry

Yes, you can connect a THC, Torch Height Controller, with the Mach3 USB controller. The THC uses the inputs to determine if the z axis needs to move up or down according to the arc of the plasma torch. The THC connects its outputs to the inputs of the controller so the controller will be informed of the states of the plasma torch.

Click the link to add information to this solution:
I am interested in using the Mach3 USB interface board. I was wondering if there was a way to run a torch height controller with this board for use with a plasma cutter, and if so do you know of any THCs that will work. Thank you.

To implement a electronics combo to run you Proxxon MF70, you will need to find the correct drive components (ACME screw, linear rail, etc) and look into any specific modifications needed to your rig.
I would recommend the USB 3 Axis Large Motors Electronics w/ USB Interface Board.
Since the machine is metal, our larger motors would be highly recommended.

We have not done this conversion, through research is recommended.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Hi I have a Proxxon MF70, I want to add 3axis stepper with controller and software by USB. Can you suggest a kit for me? Thanks.

Dealing with our scratch Build kit/BYO CNC Book Kit, you will use our basic 3 axis electronics kit (https://buildyourcnc.com/item/electronicsAndMotors-3axis-425-elcombo). Now dealing with the Breakout Board, the book specifies the parallel port BoB, but you can use the USB BoB and use Planet-CNC rather than using Mach 3 or Linux-CNC as your control software.

Click the link to add information to this solution:
Correct kit of motors and electronics, I bough a book in Amazons kindle to build a CNC, this book mention a kit of motors and electronics for parallel port, I want to use USB, can you suggest me the correct kit fot this machine.

The THC and the triggering of the plasma are actually two different functions of a controller. To trigger a plasma cutter, you can use one of the outputs of the Mach3 USB controller (out 1, 2, 3, or 4). That output can be connected to a relay that connects to the two wires that will trigger the plasma.

This video will show how this is done:

Click the link to add information to this solution:
[575] How can I wire/ configure for a plasma cutter without THC? Plasma cutter has a cnc port, where when you short two of the pins, it activates the cutter. Just looking to see how to make that short when pressing f5 in Mach3.

We have a redLeaf and redSprout system available which has all of the CNC electronics and computer system assembled as a plug and play system.

Click the link to add information to this solution:
Can you offer me a combo with motors NEMA17, NEMA23 and NEMA34 and a control box ready for plug and play operation? (this including motor drivers and cables)

These are the recommend values(default) for our blackFoot CNC machine, the acceleration and velocity can be adjusted as high as the motor can rotate without stalling! Suggested increment's will be by 10's.

blackFoot:
X-axis
“CW8060 (6.0A) Driver”
Set to 1/16 Microstep, 5.43A
Dipswitches: 01100110 (“0”=down, “1”=up)
Motor Tuning: 914.29 steps/in, Velocity 400.02, Acceleration 4

Y-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Motor Tuning: 1422.22 steps/in, Velocity 400.02, Acceleration 4

Z-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100
Motor Tuning: 1600 steps/in, Velocity 79.98, Acceleration 5

Additional Information:
Thanks! What about step and direction config? I have:
Step time: 2000ns
Step space: 8000ns
Direction hold: 5000ns
Direction Setup: 5000ns

Click the link to add information to this solution:
I am configuring a blackfoot with 1 CW8060 and 2 CW230's with linuxcnc and cannot figure out the proper settings for stepconf. Can you provide the default settings that should work with these motors?

You can find the datasheets to our motors be going to the the stepping motor category page https://www.buildyourcnc.com/category/nema and selecting the motor. This will bring you to the product page for the motor and all of the motor information will be found there.

Click the link to add information to this solution:
I would like to design my own CNC router around one of your electronics bundles, either the 3 Axis - Heavy Gantry or 3 Axis - All Large Motors. Do you have the data sheets for the motors so that I can use the dimensions in my model?

The USB interface only works with momentary switches unfortunately. If you have extensive knowledge of digital electronics, you can apply a receiver that uses a microcontroller and a transmitter with another microcontroller that produces the pulsing signal with the controls that you need.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I would like to make a handheld remote for the USB CNC Board using a joystick instead of momentary switches. Could you suggest one that will work with your board.

Please contact sales@buildyourcnc.com for a custom quote.

Click the link to add information to this solution:
I want to build a 4 x 4 plasma table. I am not good with the electronic parts of the system. What would you recommend as a turn key electronics package? I also want to build it with chain drive

Depending on the type of motors and connection type, you could adapt your motors to work with our electronic packages, but you will receive additional motors since our kit is complete.

Now you will have to take into affect the actual motors you have and compare or get accurate replacements(Ex. our 425 oz motor(1/4" input shaft) will have to be same size or similar entry holes)

Your Controller board will be the major issue, due to its wiring and processing manner, you can view the connections for our breakout boards to compare with yours! (parallel: https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/)(USB: https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/)
Email(customerservice@buildyourcnc.com for further help)

Click the link to add information to this solution:
I am looking at one of your electronics packages as a replacement for my excisting electronics. I have a old table top CNC that has a bad electronics pack, but the motors, and the mill are in good shape. could your system be adapted to work in this case?

If you purchase the greenLean, you will get everything you need except a router, computer to operate the machine, and software to control the machine. You state that you have a computer. You can use this computer, but you will need to determine if it has a parallel port, or if you are going to need the USB controller option. As for the software, there are too many different options for you to choose from. We would not be able to tell you which to get, and how much it will cost you. This is a matter of preference. I can tell you, however, that you will need 3 types of software to complete a CNC project. You will need CAD software to design your design, CAM software to add tool paths and convert the design to g-code, and then control software to take the g-code and operate the machine.

Additional Information:
20

Click the link to add information to this solution:
I am building a wet plasma table for my shop that is 8'x 16'. I will need hardware and software. Please heko me wuth the list, My phone is 9124273734. I would like to talk with someone if possible. Thanks, Rus