To select a 4 axis NEMA 17 motor and driver combination, you will need the following:

- Four (4) NEMA 17 motors: https://buildyourcnc.com/item/electronicsAndMotors-nema17-62ozin-NEWBIEHACK-motors-stepping_motor-62_ozin

- Four (4) drivers, either the 2.5A: https://buildyourcnc.com/item/motion%20electronics-steppermotordriver-newbiehack-Motor_Drivers-2!5_Amp_modular or the 3.0A: https://buildyourcnc.com/item/electronicsAndMotors-stepper-driver-3!0a

- One (1) Power supply, either the 24V or 36V (recommended): https://buildyourcnc.com/item/electronicsAndMotors-power-supply

- Finally, an interface is needed, either parallel, or USB. The USB works with planet-cnc software only. The parallel interface works with all major CNC control software: https://buildyourcnc.com/category/breakout

Click the link to add information to this solution:
Can you supply a quote for a 4 axis combo kit with NEMA 17 Motors

We send out only new products, so I'm not sure why that happened. To get an RMA, just ma the part back to us with a note of the issue and your name and address.

Send the package to
32624 SummerGlade Dr.
Wesley Chapel, FL 33545

Click the link to add information to this solution:
Board does not work for Z and A axis. Have swapped motors and drivers with no change. Note: When received package contained another package within (apparent return??). Request Return Authorization. Kevin Dawson

Controlling a 3-axis or 4-axis motor configuration, you will need the following items drivers/motors/controller. Our electronics combo comes with the items mentioned and with power supply/miscellaneous items.
The only other item needed will be a computer (with controller software) to communicate and view controls of your motors.
Using the Parallel breakout board will use Mach 3 software, and USB will use Planet-CNC software.

Additional Information:
You can use this link to see the videos on how to connect the electronics together and make them work: https://www.buildyourcnc.com/tutorials/tutorial-Electronics-USB-Interface-Wiring

Click the link to add information to this solution:
hey, where can i see the steps how can i control 3 or 4 step motor? can i use the Axis Electronics Combo? or i need to connect controller?

We don't offer those drive pullies with a 3/4" bore at the moment. We can supply them if you are willing to wait. If so, what is the pulley pitch, how many teeth and the width of the belt.

Additional Information:
Meant to say pulleys, not pullies.

Click the link to add information to this solution:
Do you offer or can recommend a place where I can buy the Drive Pulley for NEMA 43 Stepper Motor (1586 oz-in 3/4" single shaft) 5.5 Amps?

Yes, with caveats. This kit includes a controller that will not be compatible, but if you use another type of controller that has web based control, you can use these electronics. Here is a list of web based control for CNC:

- Easel: The web-based software from Inventables can be accessed through Safari or other macOS-compatible web browsers.

- bCNC: A Python-based GRBL CNC command sender, although you may need to jump through some hoops to get it to run on macOS.

- Universal Gcode Sender: A Java-based software that should run on macOS if you have the Java Runtime Environment installed.

- CNCjs: Another web-based interface that you can run on macOS using Node.js.

Click the link to add information to this solution:
[50] Is there a software control package that will work with Axis Electronics Combo (For Heavy Gantry) for apple os.

We currently do not have any Nema motor's with a .375"/3/8" shaft diameter. The motors in stock 100 oz, 425 oz, with a 1/4" input shaft. Our 651 oz, with a 1/2" input shaft.

Click the link to add information to this solution:
Your combo kits don't specify whether they are standard NEMA motors. I need Nema 34 with a .375 shaft diameter. Which 3 axis kit work for these requirements?

To use the PoKeys57CNC with KUKA, you will need to make sure that the servo drives will be able to receive pulses that are generated from their 8 step/dir signals.

The PoKeys57CNC Manual states:

PoKeys57CNC is a blend between general purpose PoKeys device and motor controller. The device is targeted primarily for controlling up to 8 STEP/DIR signal driven motors (stepper motors, servo drives, etc.)

Here is a link to the Pokeys57CNC Manual:
https://www.poscope.com/wp-content/uploads/downloads/Pokeys/Manuals/PoKeys57CNC%20user%20manual%20(23.3.2017).pdf

Click the link to add information to this solution:
Does the PoKeys57CNC board with MACH4 support simultaneous coordinated motion, as in controlling a 6 axis robot arm with large servo motors? I have 4 huge KUKA robots with complete control cabinets with all the servo drivers intact but the control language is so old and obsolete that it makes them pretty useless.

The best wiring diagram that can be used for the redLeaf and redSprout CNC computer system would be found on instruction #1 (datasheet for the breakout board) on this page: https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Click the link to add information to this solution:
Hi I live in South Africa and want to know if i can buy a wiring and component diagram for the readleaf plug and play computer system?

The best wiring diagram that can be used for the redLeaf and redSprout CNC computer system would be found on instruction #1 (datasheet for the breakout board) on this page: https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Click the link to add information to this solution:
Hi I live in South Africa and want to know if i can buy a wiring and component diagram for the readleaf plug and play computer system?

Is this a licensed version of Mach 3? If not and you are currently running the demo version, mach 3 will have only 500 lines of G-code available for cutting. Which will not allow you to cut or move the machine after the first 500 lines.

Additional Information:
Yes, It is a licensed version of Mach 3.

Click the link to add information to this solution:
Mach 3 stalls in the middle of a file and the dwell button is flashes randomly. Can't control motors and have to re-start Mach 3. Any help?

We do have a relay board that words like a standard relay.

Here is the URL of the relay board that we offer:

https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

Click the link to add information to this solution:
I HAVE YOUR MACH3 USB BOB, DO YOU GUYS SELL A TORCH CONTROL RELAY CAN WIRE UP TO TURN MY PLASMA ON AND OFF HOW WOULD WIFE THAT TOO THIS BOB?

Yes, if you need a replacement part on your machine please call us at 281-815-7701.

Click the link to add information to this solution:
I have a blacktooth laser engraver. The Y Axis stepper motor needs to be replaced. Can you please provide me with the information I would need to replace this motor.

We are currently getting it completed for us to post it under the 2.5A stepper driver page. However here is the correct wiring procedure.

First: Wire the 24V power supply to the 2.5A driver, by wiring +V on the power supply to 12-24V on the driver. Next wire the COM on the power supply to Ground(GND) on the 2.5A driver. GND on the driver will also go to the GND on the USB board, for specific axis. (additional 3-4 wires connected to ground will be needed for the other axes as well).

Second: Wire the USB board to the driver(one driver per axis on the USB board):
CP on the driver will go to CP on the desired axis on the USB board.
CW on the driver will go to CW on the desired axis on the USB board.
5V will go to the VCC pin on the keyboard jog pins on the USB board (check schematic here: https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/).
GND on the USB board to GND on the driver. (as specified in step 1).
EN is not used.

Personal Note:
I would recommend that you crimp the VCC pin to a wire which could be split for the other axes as well, each driver will need 5V.

Third: Wire the stepper motor to the driver, (using either the Nema 23 100-oz or the Nema 17 62-oz stepper motors, the wiring will be the same. For the Nema 23 the yellow and white is not connected.)
Black to A1
Green to A2
Red to B1
Blue to B2

Fourth: Repeat steps 1-3 for each driver/motor per axis.

Mention: Remember that GND on the driver will also go to the GND on the USB board for specific axis, and VCC pin on the USB board (keyboard jog) will go to 5V on all drivers for each axes as well, each driver will need 5V!

Click the link to add information to this solution:
Is there a complete wiring diagram for the Medium Combo Kit with the usb board? Your USB tutorial does not cover the modular 2.5a drivers. https://buildyourcnc.com/item/electronicsAndMotors-3axis-100-elcombo

We use the version 0024 of replicatorG which works quite well. The firmware is specified on the videos as you perform the installation. You can find the videos on this page: https://www.buildyourcnc.com/whiteAnt3DPrinterandCNCMachine.aspx

Click the link to add information to this solution:
Please share what versions of ReplicatorG, Python, Java, Firmware and the Arduino drivers you are currently using for the whiteAnt 3d printer.

Dealing with our scratch Build kit/BYO CNC Book Kit, you will use our basic 3 axis electronics kit (https://buildyourcnc.com/item/electronicsAndMotors-3axis-425-elcombo). Now dealing with the Breakout Board, the book specifies the parallel port BoB, but you can use the USB BoB and use Planet-CNC rather than using Mach 3 or Linux-CNC as your control software.

Click the link to add information to this solution:
Correct kit of motors and electronics, I bough a book in Amazons kindle to build a CNC, this book mention a kit of motors and electronics for parallel port, I want to use USB, can you suggest me the correct kit fot this machine.

At this time we are working to release a new USB controller board that will be compatible with Mach4 software and do not have any immediate plans to update the Planet-CNC USB board.

Click the link to add information to this solution:
Are there plans to release a USB Controller to work with the Planet CNC Output Board for more advanced spindle control from within Planet CNC?

Our MAch3 USB interface boards can be located here:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
I AM INTERESTED IN THE 3 AXIS COMBO USB OPTION. NOTICE YOU ENDORSE PLANET-CNC FOR USE WITH THIS BUT WILL MACH3 INTERFACE WELL BEAK OUT BOARD?

If there is play within the motor itself, then that motor may be defective. Call us to provide us more detail on this issue.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:
Ins9kru1

Additional Information:
-1 OR 2+486-486-1=0+0+0+1 --

Additional Information:
-1 OR 2+693-693-1=0+0+0+1

Additional Information:
-1' OR 2+890-890-1=0+0+0+1 --

Additional Information:
-1' OR 2+307-307-1=0+0+0+1 or 'HN9afNei'='

Additional Information:
-1" OR 2+88-88-1=0+0+0+1 --

Additional Information:
1'"

Additional Information:
1����%2527%2522

Additional Information:
@@mxOzC

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I have NEMA 34 motors for a GreenBull 6x12. After 2 weeks of use, my Y axis motor has developed play in the front but not rear of the motor. Is this a motor defect or has something come loose somewhere? Thanks,

Identify the Control Signals: First, determine which control signals from the DB25 interface card are used for spindle speed control. Typically, these are PWM (Pulse Width Modulation) signals or analog voltage signals.

VFD Configuration: Your VFD should be configured to accept the type of control signal your DB25 card provides. This involves setting parameters in the VFD that correspond to the type of input signal it will receive for speed control.

Wiring: Connect the appropriate output pins from the DB25 card to the input terminals on the VFD. This usually involves connecting the PWM or analog output to the corresponding input on the VFD. Make sure to consult the manuals for both your VFD and interface card for specific wiring details.

UCCNC Settings: Configure UCCNC to output the correct type of signal (PWM or analog) that matches your VFD's configuration. This is done through the software's spindle setup section.

Test and Adjust: Run some tests to ensure that the spindle speed is being correctly controlled by UCCNC. You might need to tweak settings in either the VFD or UCCNC for optimal performance.

Click the link to add information to this solution:
HEY ! I HAVE PURCHASED A VFD WITH MATCHING SPINDLE 1.5KW AND CONTROL PROGRAM UCCNC. MY INTERFACE CARD IS DB25, THE QUESTION HOW DO CONNECT TO DB25 SO THAT CAN SPEED UCCNC? SINCERELY "CNC BEGINNERS"