The use of the hex inverter in the application to invert a direction signal to have a motor run in the reverse directions is relatively simple.

First, go to this link and look at the chip diagram:
https://www.buildyourcnc.com/item/electronicsAndMotors-hex-inverter-breakout-newbiehack-integrated_circuits-hex-inverter

Connect 5V from the USB interface tothe VCC pin. The pin on the keyboard jog header can be used. Connect the GND pin from the USB interface to the GND pin on the hex inverter. Connect the CW terminal from the USB interface to the 1A pin on the hex inverter. Connect the 1Y pin from the hex inverter to the driver.

Additional Information:
I got a question??? I am a dummy when it comes to cnc. I got 6040 1500kw water cold engraver 3 axis from china. I can not get anything out of them pertaining help they keep telling me the same thing over and over and over and I'm doing it and send them pictures that I know. Anyway email me a wiring diagram for the PRT 1500 watt spindle motor control box and has the emergency stop on and off switch manual PC and of course yhe screanm fultonsbusiness@gmail.com

Additional Information:
I got a question??? I am a dummy when it comes to cnc. I got 6040 1500kw water cold engraver 3 axis from china. I can not get anything out of them pertaining help they keep telling me the same thing over and over and over and I'm doing it and send them pictures that I know. Anyway email me a wiring diagram for the PRT 1500 watt spindle motor control box and has the emergency stop on and off switch manual PC and of course yhe screanm fultonsbusiness@gmail.com

Click the link to add information to this solution:
Is there a wiring diagram for hooking up your hex inverter between your USB breakout board and the controller?

The board layout is different and the terminals have slightly different names, but the two boards function the same. The wiring diagram is the same for both boards. The plug-in driver for Mach3 is also the same, so you should not have a problem. If you do run into an issue, please let me know here and I will help you determine the problem.

Thanks

Additional Information:
Thank you for the assurance that the boards will function the same. You did not answer the primary question of wiring. The diagram shows a board with a 5V for each axis, the new boards have only 1 5V point on the axis side. In retrospect since this controller receives information and most possibly the 5V signal directly from the computer leading to the drivers. I will wire the X, Y and Z axis to the single 5V point and see what happens.

Click the link to add information to this solution:
received my mach 3 USB breakout board today. The layout of the board is different from your diagram which shows a 5V power slot for each axis. Do I wire the 5V slot with only one 5V wire from one of the drivers or perhaps wire all three 5V wires into the one 5 V slot. Please advise.

All the options for and variations of our blackTooth laser cutter/engraver are available on our website here https://buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx#prettyPhoto. The wiring diagram is available here: https://buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx#prettyPhoto/0/
We do not offer plans or a bill of materials for our machines at this time, but if you are interested in doing your own from scratch you can learn a lot about the design and build process from our tutorials. We wish you success in your endeavors.

Click the link to add information to this solution:
How can i get a complete list of all the components (electronics) I need for a CNC laser cutter with the laser controller? A wiring Diagram would probably be very helpful.

For our parallel breakout board (https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/) the schematic will show the connections going from the BB to the drivers. The parallel breakout board uses the 25 pin parallel connection to communicate from the computer to drivers, and the USB is used to power the main-board itself, supplying 5V.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
The electronics package I just bought from you (Book Build) is different from your wireing diagrams and video tutorials. Is there an updated wiring diagram available? Is the USB port on the breakout board connected directly to the computer USB to supply 5 volts? Thank you.

Did you connect the USB connector to the breakout board?

Additional Information:
YES I CONNECTED THE USB TO THE BREAKOUT BOARD

Click the link to add information to this solution:
I connected the electronics (for 2 x 4 feet) that I ordered from you. But how do I check if I connected all the wiring properly. There is neither any light on motor drivers nor on breakout board. And the motor shaft also does not move before and after the power supply is given.

You will need a 24v power supply if you wish to use the inputs or output on that side of the board. A 12V power supply will work if you only need to use the inputs.

The inputs on that side of the board are typically used for limit switches, emergency stop, or homing switches. The outputs on that side of the controller are typically used to turn on and off machine devices such as spindle, coolant valve, etc. There is also a 0-10V PWM output on that side of the board.

Additional Information:
Another solution would be to purchase an expensive 36VDC-->24VDC convert..just connected to one of the DC outputs on your 36VDC PS and you don't have to purchase another large 24DC PS.. The power requirement is pretty low so it won't/shouldn't affect the 36VDC used to drive motors/etc.

Click the link to add information to this solution:
Hello purchased a 3 axis elect. combo (heavy gantry). Printed a wiring dia. for the mach3 USB board from the page with the picture of the Mach3 USB board. Question; wiring schm. showes USB board wierd to a 24v/12v power supply. Power that came with combo kit is 36v. This work ok? Thanks for info

The firmware update for the USB board is done by PlanetCNC. with your board hooked up to the computer via USB cable, log into PlanetCNC. Then, from the Machine tab on the toolbar choose firmware from the drop down and click on update.

Click the link to add information to this solution:
Is there a firmware update in the last two years for your USB board? If so how do we get it and install? If not do you expect any updates? If updates are released how do we find out?

The stepper motor on the X axis on the VLXL is this motor here:
https://www.buildyourcnc.com/item/electronicsAndMotors-nema34-651ozin

There is no black lead on that motor and the connection diagram can be found here:
https://www.buildyourcnc.com/Documents/PN.SM86HT80-5504B-U(inhouse%20PN.85BYGH450A-47-80)%20(1).pdf

Red - A+
Green - A-
Yellow - B+
Blue - B-

The wiring diagram on the instructions for the Vertical Laser XL is meant as a general guide for all laser systems. The motor specific to the axis should be checked against the datasheet to insure proper wiring.

The 24V power supply should be connected to the laser controller. The 36V power supply should be connected to the drivers to power the motion electronics.

Additional Information:
My fault. Must have had that backwards. I'm sure he told me the right way.

Additional Information:
Not a problem. The laser controller has two terminals labeled for the 24V connection.

The 36V power supply works really well for stepper motor drivers as the voltage/current on this power supply allows for best stepper motor performance with this laser application.

Click the link to add information to this solution:
Hello! Question about the x motor on the vlxl. There is no black lead. Is the yellow in its position? Also, I really just want to double check that this wiring diagram is solid. About to finish the wiring. Juan told me to use the 36V for the tube and 24 for the drivers. Correct?

If you want speed control, it is recommended to use the RS-485 connection on the VFD and use the control program such as Mach3 to communication serially with the VFD using this RS-485 connection.

If you would rather use a controller such as the PMDX-107 to simulate the effect of a potentiometer using the Aref, Aout and Agnd and the Rev/Dir and Fwd/Run terminals to control operation and direction, you can connect those to the VFD.

PMDX-107 Aout connects to the VI (analog voltage in). This is like the wiper on a potentiometer.
PMDX-107 Agnd connects to the ACM terminal on the VFD for Analog common.
PMDX-107 COM connects to DCM terminal on the VFD for Digital common.
PMDX-107 Fwd/Run connects to the FOR terminal on the VFD for Forward.
PMDX-107 Rev/Dir connects to the REV terminal on the VFD for Reverse.

Refer to your PMDX-107 manual to correctly configure your dip switch settings and make sure to calibrate (tweak) the speed control using the trimmer next to the terminals on the PMDX-107.

Click the link to add information to this solution:
I have the USB controller board and the 8825 step driver. I need a wiring diagram between the two. Specifically, what does the GND pin on the X-axis connect to? Also, what does the 5V pin on the driver connect to?

You can find a wiring diagram here:
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/

The CP terminal is wired to the step terminal on the 8825 step driver.
The CW terminal is wired to the direction terminal on the 8825 step driver.
The GND terminal connects to the GND on the 8825 step driver

The 5V connector on the driver simply powers the logic side of the chip and needs to connect to VCC pin on the keyboard jog.

Customer Response:
Thanks! Working now.

Click the link to add information to this solution:
I have the USB controller board and the 8825 step driver. I need a wiring diagram between the two. Specifically, what does the GND pin on the X-axis connect to? Also, what does the 5V pin on the driver connect to?

To use the PoKeys57CNC with KUKA, you will need to make sure that the servo drives will be able to receive pulses that are generated from their 8 step/dir signals.

The PoKeys57CNC Manual states:

PoKeys57CNC is a blend between general purpose PoKeys device and motor controller. The device is targeted primarily for controlling up to 8 STEP/DIR signal driven motors (stepper motors, servo drives, etc.)

Here is a link to the Pokeys57CNC Manual:
https://www.poscope.com/wp-content/uploads/downloads/Pokeys/Manuals/PoKeys57CNC%20user%20manual%20(23.3.2017).pdf

Click the link to add information to this solution:
Does the PoKeys57CNC board with MACH4 support simultaneous coordinated motion, as in controlling a 6 axis robot arm with large servo motors? I have 4 huge KUKA robots with complete control cabinets with all the servo drivers intact but the control language is so old and obsolete that it makes them pretty useless.

We send out only new products, so I'm not sure why that happened. To get an RMA, just ma the part back to us with a note of the issue and your name and address.

Send the package to
32624 SummerGlade Dr.
Wesley Chapel, FL 33545

Click the link to add information to this solution:
Board does not work for Z and A axis. Have swapped motors and drivers with no change. Note: When received package contained another package within (apparent return??). Request Return Authorization. Kevin Dawson

The leadscrew length for the greenBull long Z-axis is 47 inches.

Additional Information:

Click the link to add information to this solution:
BUILDING ONE OF YOUR GREENBULL 6X LONG AND 2.2 KILOWATT SPINDLE DOES NOT FIT. SEEMS LEAD SCREW YOU SENT WITH KIT IS SHORT 42" LOOKS LIKE IT NEEDS TO BE 5 OR 6 INCH LONGER. THIS CORRECT? WHAT THE NEEDED LENGTH FOR UNIT?

The connections for the Mach3 USB CNC Machine interface card you refer to is connected as follows:
- All of the "D" connections such as XD, YD, ZD and AD are the direction connections and are connected to the CW- connections on the drivers.
- All of the "P" connections such as XP, YP, ZP and AP are the pulse connections are are connected to the CP- connections on the drivers.
- The 5V connections on the USB board are connected to the CP+ and CW+

Here is a link to the wiring diagram:
https://www.buildyourcnc.com/Documents/Electric%20Wiring%20Diagram.pdf

Click the link to add information to this solution:
the tutorial for the discontinued usb card is great but i have your usb motion card stb4100 i need with AD AP +5v wired to the cp+cp-cw+and the cw-

Our 1.5/2.2kW spindle will work with both setups, in our wiring diagram it is more seen as the Euro/AUS-style, however you can do the same thing with the North American style as well. Also depending on if you have single or three phase 220V, you can use pins R, S, T. A manual will arrive in the VFD box, which will have further information and diagrams.

Please seek a certified electrician if you are unsure of any aspect in wiring the spindle or VFD, since wiring to main lines will require wiring of the plug and main lines to the inverter and to avoid any damage or injury's while installing the 1.5/2.2kW spindle and VFD combo.

Click the link to add information to this solution:
On the wiring diagrams for the 220v inverters I noticed that there is one hot (220) a neutral and a ground. Will the inverter work with the American split phase system? Hot (120) hot (120) ground?

I also place the controller very close to the drivers (on the back of the gantry). All of the cables are shielded. The only long cables are the mains power cables and the USB cable. The USB cable is shielded and contains active repeaters.

There is no problem putting all of the electronics in a box and using long cables to the motors. This is the way I did it for a very long time.

Click the link to add information to this solution:
Great site. I saw your videos of wiring the Mach3 USB controller. You place the drivers next to the Steppers. This means that you have very long leads to the USB Board? What about the placement of the controlling PC? Is it a problem to have the USB board, PSUs and Drivers in a control box and long leads to the steppers? Thank you.

Yes, you can connect a THC, Torch Height Controller, with the Mach3 USB controller. The THC uses the inputs to determine if the z axis needs to move up or down according to the arc of the plasma torch. The THC connects its outputs to the inputs of the controller so the controller will be informed of the states of the plasma torch.

Click the link to add information to this solution:
I am interested in using the Mach3 USB interface board. I was wondering if there was a way to run a torch height controller with this board for use with a plasma cutter, and if so do you know of any THCs that will work. Thank you.

We are currently working on a relay board that will connect to USB breakout board, and the router/spindle for both the on/off function. Unfortunately we still do not have it completed or ready to be placed on our website, but it is in the final stages of testing. Please check back regularly for updated stock!

Here is a link to a tutorial for a DIY relay circuit:

Click the link to add information to this solution:
I AM PUTTING TOGETHER THE BLACKFOOT AND USING A PORTER CABLE ROUTER. CONFUSED ON HOW TO RELAY ROUTETR WITH USB BOARD. IS THERE ANOTHER SWITCH THAT GOES BETWEEN BOARD ROUTER SO PLANET CNC CAN TURN PERHAPS VACUUM OFF?

The USB interface only works with momentary switches unfortunately. If you have extensive knowledge of digital electronics, you can apply a receiver that uses a microcontroller and a transmitter with another microcontroller that produces the pulsing signal with the controls that you need.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I would like to make a handheld remote for the USB CNC Board using a joystick instead of momentary switches. Could you suggest one that will work with your board.