Did you connect the USB connector to the breakout board?

Additional Information:
YES I CONNECTED THE USB TO THE BREAKOUT BOARD

Click the link to add information to this solution:
I connected the electronics (for 2 x 4 feet) that I ordered from you. But how do I check if I connected all the wiring properly. There is neither any light on motor drivers nor on breakout board. And the motor shaft also does not move before and after the power supply is given.

The Mach3 USB will not work with Linux CNC. You can use our parallel breakout baord instead (if you have a computer that has a parallel port available).

Here is the link to that interface:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Click the link to add information to this solution:
Hello. I'm currently building my first CNC router, and I'm powering it with a 3 axis electronics kit that was purchased through your site. I chose to get the Mach 3 USB Breakout board, but now I'm wanting to try to use Linux CNC to work with the computer I have available. Will that work with this board?

The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.

Click the link to add information to this solution:
I bought a 'BuildyourCNC V1' relay board to go with my mach3 usb controller. I have been sent a 'Songle' relay. It's not the one in your picture and it's got different connections, for which there isn't a wiring diagram. The one I ordered says it is 5v, this one seems to be saying it's a 24v unit. Can you please explain what has happened? Thanks

The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.

Click the link to add information to this solution:
I bought a 'BuildyourCNC V1' relay board to go with my mach3 usb controller. I have been sent a 'Songle' relay. It's not the one in your picture and it's got different connections, for which there isn't a wiring diagram. The one I ordered says it is 5v, this one seems to be saying it's a 24v unit. Can you please explain what has happened? Thanks

The digital signal portion of the CO2 laser tube power supply has various terminals for signal power, signal gnd, laser intensity and engaging the laser (turning it on or off). The TL and TH are triggers to turn the laser power on or off. These may be labeled L or H on some laser power supplies. You can use either TL/L, or TH/H to control the laser.

If you use the TL or L terminal to control the laser:
If a low signal (gnd) is present at that terminal, the laser will turn on. If a high signal (5v) is present, the laser will turn off.

If you use the TH or H terminal to control the laser:
If a high signal (5v) is present at that terminal, the laser will turn on. If a low signal (gnd) is present, the laser will turn off.

You should first test the control signal from the interface with a multimeter to make sure the laser will be controlled correctly before powering the laser power supply

Click the link to add information to this solution:
On the blacktooth machine wiring diagram for parallel breakout a wire goes from 6 on the BOB to TL on the laser power supply. My power supply has an"H" followed by a "L". Which is correct? I've connected to the "L" but the laser appears always on.

You will need PlanetCNC software for the USB breakout board and when plugging in the USB the computer should automatically recognize the board, however you can go into device manager to see if the USB terminal is working correctly.
The parallel breakout board; the USB is not a connection terminal rather than a power source, and the parallel port will be the communication terminal.
The items you will need for a water cooled spindle would be: water pump, silicon tubing(length desired by customer), a extension cord(from a hardware store(orange))(1 same gauge wire/length as extension cord).

Click the link to add information to this solution:
I am making my own CNC setup using all the electronics from your website and I have many questions. Please advise how to have my computer recognize the USB connection from my breakout board also I would like to use a water cooled spindle but I need to know the parts required for a 4x10 bed area used for woods and plastics

I can provide a paypal invoice for the difference in price. Just give me an email at customerservice@buildyourcnc.com and then I can send you the invoice.

Additional Information:
I can provide a paypal invoice for the difference in price. Just give me an email at customerservice@buildyourcnc.com and then I can send you the invoice.

Additional Information:
thats great thank you. please send it to james_moya@hotmail.com and i will be paying with my cc.

Additional Information:
thats great thank you. please send it to james_moya@hotmail.com and i will be paying with my cc.

Click the link to add information to this solution:
i placed an order with you on 5.27.20 for 3 stepper motors. i realize now i need the rest of the electronics (drivers, breakout board power supply etc...) i see you offer a bundle and would like to know how i can get the rest of the bundle. im looking at the $390 bundle without the motors obviously. please advise. thank you

Hi, this BBB comes with a USB port and its cable to power it up. Once connected to the computer a led in the BBB will light up to show it has power.

Additional Information:
Breakout board I have does not have USB port for the 5v power. Does the parallel port supply the 5V power?

Click the link to add information to this solution:
Hi, I need assistance, the parallel breakout board I received looks different from the one on the video, does this one need a 5V supply? If so, where do I connect the positive and where do I connect the ground? Thanks for your help.

The board layout is different and the terminals have slightly different names, but the two boards function the same. The wiring diagram is the same for both boards. The plug-in driver for Mach3 is also the same, so you should not have a problem. If you do run into an issue, please let me know here and I will help you determine the problem.

Thanks

Additional Information:
Thank you for the assurance that the boards will function the same. You did not answer the primary question of wiring. The diagram shows a board with a 5V for each axis, the new boards have only 1 5V point on the axis side. In retrospect since this controller receives information and most possibly the 5V signal directly from the computer leading to the drivers. I will wire the X, Y and Z axis to the single 5V point and see what happens.

Click the link to add information to this solution:
received my mach 3 USB breakout board today. The layout of the board is different from your diagram which shows a 5V power slot for each axis. Do I wire the 5V slot with only one 5V wire from one of the drivers or perhaps wire all three 5V wires into the one 5 V slot. Please advise.

Attaching two motors in parallel is possible, but you will need another motor and driver for the opposite side. Each motor must have its own driver to work accordingly and fluently. The two can be wired together, to the same pins on your breakout board and set the dip switches on the driver to match the ones on your x-axis(ex). But remember to view the orientation of the motor and which way it spins, since it is on the opposite side it will have to be orientated correctly to move in sync with the other motor.

Click the link to add information to this solution:
I just finished building my first CNC with the electronics I purchased from you and I am already thinking about improving it. I would like to build a 2 motor X axis solution. Is it possible to attach 2 parallel motors and drivers to the BlueBrew Breakout Board? If so, how?

For our parallel breakout board (https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/) the schematic will show the connections going from the BB to the drivers. The parallel breakout board uses the 25 pin parallel connection to communicate from the computer to drivers, and the USB is used to power the main-board itself, supplying 5V.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I am wiring my breakout board and it has a USB port on it. Is the USB port there to supply the 5 volt power to it?

Sure, email me at customerservice@buildyourcnc.com and I will send you a replacement for a minimal fee. I now use HDPE for that part. The HDPE holds up much better.

Click the link to add information to this solution:
I have a Blackfoot 4x4 v2 chain drive. my Y plate is broken . do you sell just the Y plate or can I buy just the Y plate spec plan? I love this machine Its great. my name is Jeff Krug I bought the complete package and electronics from you guys. thanks

Youmay be able to find an adapter for your cable, or even a new cable, locally. This is the cable we sell that will work, https://www.buildyourcnc.com/item/electronicsAndMotors-cable-wire-db25-male-male

Click the link to add information to this solution:
The female 25 pin socket on my computer has to be connected to a similar socket on the breakout (parallel) board which came with my Blacktooth. Do I need a DB25 to DB25 cable, if such a thing exists? The cable I have is male to female.

The use of the hex inverter in the application to invert a direction signal to have a motor run in the reverse directions is relatively simple.

First, go to this link and look at the chip diagram:
https://www.buildyourcnc.com/item/electronicsAndMotors-hex-inverter-breakout-newbiehack-integrated_circuits-hex-inverter

Connect 5V from the USB interface tothe VCC pin. The pin on the keyboard jog header can be used. Connect the GND pin from the USB interface to the GND pin on the hex inverter. Connect the CW terminal from the USB interface to the 1A pin on the hex inverter. Connect the 1Y pin from the hex inverter to the driver.

Additional Information:
I got a question??? I am a dummy when it comes to cnc. I got 6040 1500kw water cold engraver 3 axis from china. I can not get anything out of them pertaining help they keep telling me the same thing over and over and over and I'm doing it and send them pictures that I know. Anyway email me a wiring diagram for the PRT 1500 watt spindle motor control box and has the emergency stop on and off switch manual PC and of course yhe screanm fultonsbusiness@gmail.com

Additional Information:
I got a question??? I am a dummy when it comes to cnc. I got 6040 1500kw water cold engraver 3 axis from china. I can not get anything out of them pertaining help they keep telling me the same thing over and over and over and I'm doing it and send them pictures that I know. Anyway email me a wiring diagram for the PRT 1500 watt spindle motor control box and has the emergency stop on and off switch manual PC and of course yhe screanm fultonsbusiness@gmail.com

Click the link to add information to this solution:
Is there a wiring diagram for hooking up your hex inverter between your USB breakout board and the controller?

The whiteAnt is no longer sold; the information on the website is to support legacy customers. We have spoken with you and are sending the materials that you need.

Click the link to add information to this solution:
I am having difficulty with the wiring on the White Ant. The latest electronics that I received don't seem to be anything like the book or even the tutorials. For instance, the three stepper drivers need 6 pin connectors and ribbon cable. How are they wired? There was no thermocouple wire included. Thanks,

Red is A+
Blue is A-
Black is B+
and Green is B-

Click the link to add information to this solution:
I purchased the 3 Axis Heavy Gantry Electronics /w Pokeys57CNC controller and the motors supplied only have 4 wires coming out of them (R,G,B,Blk). Your wiring video shows wiring 8 cables. do you have a video showing how to wire the 4 wire version?

The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.

Click the link to add information to this solution:
I have your Mach3 usb interface board and am interested in the relay board to turn plasma torch on/off. I have a different relay board that doesn't work, it needs 0/5v from output pin to trigger and the usb board doesn't put out 5 volts. Does this relay board need 5v on output or will work fine with this usb controller?

Most motherboard do contain parallel ports, but the port connector may not be at the back (in the section where external connectors will be connected). Instead, the motherboard may contain an LPT ribbon connector on the actual face of the motherboard (usually along one of the edges). You will need a ribbon connector to a DB25 female connector.

If your motherboard does not contain an LPT header on the motherboard, you can purchase a parallel printer adapter that plugs into one of the PCI slots. The price of the adapter is very inexpensive and sometimes is actually less costly than the actual ribbon connector.

Click the link to add information to this solution:
As I am building my 20" x 24" laser engraver cutter, I notice that there is no parallel port on the onboard computer and I have the parallel breakout board any answers?

Sure, the USB interface has a place for 4 axes of limit switches.

Each axis can have two limit switches: one for the ++ (positive) end and one for the -- (negative) end. The positive end would be the limit switch at the end of the machine that, say the machine has a 4'x8' area, reaches a bit after the 8 foot mark. The negative end would be the limit switch behind the 0 foot location behind the origin. If the origin is in the middle, the negative would be at a little more than the -4 foot end and the positive would be at a bit more than the +4 foot end. Note that you can have more than one switch on each pin where the NC is connected in serial fashion and the NO is connected in parallel fashion (this can be seen on the diagram in the multiple limits switch section). The software configurations for the limits switches are under File -> Settings -> Limit.

A typical limit switch has three connections on it. These connections consist of COM (common), NC (normally closed) and NO (normally open). The COM would generally go to GND and the NC or the NO would go to the pin. If the NC is used, then the the switch is constantly connected until the switch is pushed (engaged) then the connection from the pin to gnd is broken (open). Use the settings in software to set whether in NC or NO configuration.

Let me know if this information was helpful (or not) by adding information to this question. Thanks.

User response:
Thank you very much for this helpful information. I'm still a little fuzzy on how the 6 limit switches physically connect to each other and to the USB breakout board. You've stated one switch (home) goes to positive and another switch (limit) goes to negative. Are all the GND prongs from all 6 switches connected to each other and going to GND on the breakout board, or no? And the NC prongs, how exactly are they connected to each other? And to the board? There has to be a diagram somewhere shows this visually, no? I don't know how to wire the switches in series or in parallel. I have already physically installed all the switches on the machine and ran the wires to where the board is. Now I just need to know where to plug these wires into the board. Also, taking into consideration that I'm using the Planet CNC software, the only settings I have pertaining to limit switches is "Enable/Disable" for each axis, and the actual limit for each axis. Nothing about NC or NO. Is that only in Mach3?
Thank you.

buildyourcnc response:
On the USB interface, the COM on the switch connects to GND and the NC or NO connects to the input pin (i.e. x++, y--, etc.)

Limit switch configuration is rather difficult to understand, especially with series and parallel. You can think of series as a single wire going from GND to the axis letter input terminal (i.e. X++ or X--). If the wire is broken, then the circuit is open (or the switch is engaged in a normally closed scenario). Normally closed is like an actual wire, and when engaged, the switch "opens" (breaks the wire). This is why we recommend in some systems that you can put many switches in series on a single pin. When one of the switches is engaged (breaking the connection) then the entire circuit of switches is broken and the machine stops.

In a parallel scenario, the state of the circuit is always broken until the one of the switches is engaged and the circuit is then closed or connected. The topology looks like a ladder. All the switches connect to both sides of the ladder and the switches are like the runs of the ladder (the horizontal bars that the feet are placed while climbing). Imagine all of the switches broken in this scenario (normally open). It would be like the ladder could be split in two, but if one of the ladder runs (switches) is closed by engaging it, then that run would connect both sides of the ladder and the two sides of the ladder would have a connection.

There is a diagram on the USB page of the various limit switch configurations. If you need more information (visual and/or otherwise), please let us know and we will immediately add that information to benefit everyone.

Click the link to add information to this solution:
I have nearly completed the CNC machine from the book, but I am using it with a USB breakout board, and have no idea how to wire the 6 limit switches to the board. I'm having difficulty following the diagram on the USB breakout board screen. Can someone please help me?