The board layout is different and the terminals have slightly different names, but the two boards function the same. The wiring diagram is the same for both boards. The plug-in driver for Mach3 is also the same, so you should not have a problem. If you do run into an issue, please let me know here and I will help you determine the problem.

Thanks

Additional Information:
Thank you for the assurance that the boards will function the same. You did not answer the primary question of wiring. The diagram shows a board with a 5V for each axis, the new boards have only 1 5V point on the axis side. In retrospect since this controller receives information and most possibly the 5V signal directly from the computer leading to the drivers. I will wire the X, Y and Z axis to the single 5V point and see what happens.

Click the link to add information to this solution:
received my mach 3 USB breakout board today. The layout of the board is different from your diagram which shows a 5V power slot for each axis. Do I wire the 5V slot with only one 5V wire from one of the drivers or perhaps wire all three 5V wires into the one 5 V slot. Please advise.

The datasheet for the parallel breakout board is here:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/

The datasheet for the USB interface is here:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/


Additional Information:
20

Click the link to add information to this solution:
I need wiring instructions for the breakout board you sent yesterday. It is not like the one in the videos and I don't know where to connect the 5V. No data sheet or anything.

The 5V power required for the breakout board can be a simple USB male to male cable, that will connect from your computer to the board itself.
Now adding a external power supply make sure that it does not exceed a total of 5V and the standard 500 MilliAMP - 1 A.

Click the link to add information to this solution:
I have a YDH-18-5 Power Supply AC Input:100-240v 47-63Hz, Ouput: 5v - 2A and need to know if its safe to use with the Parallel Breakout Board.

I would not recommend slaving an axis using the method of taking an additional axis from the USB interface. Instead, wire both drivers to a single axis on the USB interface. This will insure perfect signal output to both drivers. If you requre the motors to spin in opposite directions, simply wire one of the motors to the driver reversing the coil A and B connections, or use a hex inverter (https://www.buildyourcnc.com/tutorials/Tutorial-Two-Motors-Spinning-Oppositely-On-Single-Axis).

Click the link to add information to this solution:
I purchased a USB Breakout board, motors and drivers, paid for CNC USB Controller Software and I CAN NOT "Slave" an axis, but there is an option to do that. The moment I connect USB Breakout Board "Slave" option becomes shaded and I can no longer select it (becomes not functional). What is going on? Need help asap. Thanks

For our parallel breakout board (https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/) the schematic will show the connections going from the BB to the drivers. The parallel breakout board uses the 25 pin parallel connection to communicate from the computer to drivers, and the USB is used to power the main-board itself, supplying 5V.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
The electronics package I just bought from you (Book Build) is different from your wireing diagrams and video tutorials. Is there an updated wiring diagram available? Is the USB port on the breakout board connected directly to the computer USB to supply 5 volts? Thank you.

https://buildyourcnc.com/Item/electronicsAndMotors-electronic-component-e-stop-button-switch-safety#prettyPhoto/0/

Click the link to add information to this solution:
How do I wire up multiple E-stop to breakout board, does each E-stop need there own pin? If not since there are only 4 screws on stop 2 for no and 2 for nc do you just splice the wires together if your only using 1 pin? Thanks

Here is how to connect your router to the parallel breakout board through the on-board relay. You will need a spare extension cord. You will need to remove a portion of the outer jacket of the extension cord to expose the white, black and green wires (white = neutral, black = live and green = ground), understanding that the neutral and live create the completed circuit.

See this image of a similar connection. The terminal has the same connections.
https://www.buildyourcnc.com/images/vacuum-pressure-controller-relay-terminals-700.JPG

Image of the relay terminal:
https://www.buildyourcnc.com/images/breakoutboardrelayNONC.PNG

The live/black wire would be cut and one end of the cut would be secured into the P terminal and the other cut end would be secured into the S terminal. The live and ground wire would be uncut and travel from the plug to the router.


Additional Information:
You can also connect other high powered devices to the breakout board using any of the output terminals. You will need to supply extra relays like the one shown here:
https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

Or you can find SSRs (Solid State Relays) that will accept 5v to drive the relay coil. Make sure the SSR will protect the 5V line from Back EMF as there is a coil in the relay. The one we sell contains a fly-back diode to protect the 5v terminal.

Click the link to add information to this solution:
I have your breakout board with relay parallel port , I have a vacuum, light on router and air pump I want to also hook up to board, can I hook those up to board and also could I had reylays to each one, what is the best way to figure this out any information would be great. Thanks

The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.

Click the link to add information to this solution:
I have your Mach3 usb interface board and am interested in the relay board to turn plasma torch on/off. I have a different relay board that doesn't work, it needs 0/5v from output pin to trigger and the usb board doesn't put out 5 volts. Does this relay board need 5v on output or will work fine with this usb controller?

I just posted the "enhanced" Blacktooth wiring diagram I developed. Check it out here.

http://www.buildyourtools.com/phpBB3/viewtopic.php?f=12&t=4872

Click the link to add information to this solution:
Where do I wire the ground of my "th" and "power 0v - 5v" command on the power supply ? Is it possible to have a detailed blueprint of the electrical wiring (not for the blacktooth but in general) ? Many thanks :)

That was one of our older models, which we did not have any specific ground pins on our board, they were not added and we currently updated our board to include them.

For the random triggers for the limits and e-stop, we recommend having these wired separate from any other wires (communication, power, etc), and we recommend shielded cable as well! These will be very sensitive to noise and any interference that might be present.

Our newer model Parallel BoB: https://buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Click the link to add information to this solution:
on the parallel breakout board I have, there are two 5v inputs on the limit swith side and no ground label. https://www.dropbox.com/s/hxeojviveteqq2f/IMG_7947.jpeg?dl=0 I have used an external ground for now but I am getting random limit and e-stop triggers. please advise

VCC is the same as 5v. I will clarify on the instructions.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
In the BlackTooth instruction the concluding sentence suggests connecting a wire from the right terminal of the pot to the VCC on the Laser Supply. There is no VCC on the power supply for the Laser that I can find. So, does this wire go to a different terminal on the power supply, or somewhere else where VCC exists, such as either stepper motor control?

Did you connect the USB connector to the breakout board?

Additional Information:
YES I CONNECTED THE USB TO THE BREAKOUT BOARD

Click the link to add information to this solution:
I connected the electronics (for 2 x 4 feet) that I ordered from you. But how do I check if I connected all the wiring properly. There is neither any light on motor drivers nor on breakout board. And the motor shaft also does not move before and after the power supply is given.

To connect the parallel port breakout board to the LEDs, use step number 18. The connections are listed at the bottom. Here it is for your convenience.

For the LED connections on the parallel breakout board:

- The x axis LED will be connected to pin #2 and 5V
- The y axis LED will be connected to pin #4 and 5V
- The laser on/off LED is connected to pin #6 and 5V

Click the link to add information to this solution:
I can't find any information in the BlackTooth instructions about how to connect the 8 wires from the LED display to the parallel breakout board. The two going to the pot seem, in the illustration, to be soldered together and to the centre terminal of the pot? Help, please.

To setup mach3 for the parallel breakout board, view the last three videos on this page:
https://buildyourcnc.com/CNCElectronicsandWiring.aspx#prettyPhoto

The parallel breakout board contains a usb connector, but is only used for power. The USB interface board (sold here: https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout) does not use Mach3, rather it uses the planet-cnc software.

Click the link to add information to this solution:
bluechic v4.2 - mach3 setup video does not play on the metacafe site... since I'm new to this I am lost on how to configure mach3 to the usb breakout board. Please advise, thanks!

Attaching two motors in parallel is possible, but you will need another motor and driver for the opposite side. Each motor must have its own driver to work accordingly and fluently. The two can be wired together, to the same pins on your breakout board and set the dip switches on the driver to match the ones on your x-axis(ex). But remember to view the orientation of the motor and which way it spins, since it is on the opposite side it will have to be orientated correctly to move in sync with the other motor.

Click the link to add information to this solution:
I just finished building my first CNC with the electronics I purchased from you and I am already thinking about improving it. I would like to build a 2 motor X axis solution. Is it possible to attach 2 parallel motors and drivers to the BlueBrew Breakout Board? If so, how?

The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.

Click the link to add information to this solution:
I bought a 'BuildyourCNC V1' relay board to go with my mach3 usb controller. I have been sent a 'Songle' relay. It's not the one in your picture and it's got different connections, for which there isn't a wiring diagram. The one I ordered says it is 5v, this one seems to be saying it's a 24v unit. Can you please explain what has happened? Thanks

The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.

Click the link to add information to this solution:
I bought a 'BuildyourCNC V1' relay board to go with my mach3 usb controller. I have been sent a 'Songle' relay. It's not the one in your picture and it's got different connections, for which there isn't a wiring diagram. The one I ordered says it is 5v, this one seems to be saying it's a 24v unit. Can you please explain what has happened? Thanks

I would recommend using a separate 24VDC power supply for the controller. The 24VDC that is connected to the controller is used for delicate input signals and output signals that control external devices. To keep interference and possible current and voltage fluctuations at a minimum due to the motor load, a separate power supply would be best.

Click the link to add information to this solution:
[575] Can the 24VDC supply used for the interface board be the same supply used for stepper drivers, or do you need separate power supplies? If not, does GND and DCM need to be isolated?

The USB Interface page: https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout

On this page, there is a datasheet that explains the connection schemes for the limit switches on step 1 of the instructions. The datasheet explains single and multiple switch configurations and parallel/serial connections schemes for the NO/NC (Normally Open/Normally Closed states).

If there is further information you need, please reply on this FAQ.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Please provide detailed instructions on how to connect limit switches to CNC USB BOARD. I can not find instructions anywhere. I am new to cnc world and really need help. Thanks