We currently do not have any Nema motor's with a .375"/3/8" shaft diameter. The motors in stock 100 oz, 425 oz, with a 1/4" input shaft. Our 651 oz, with a 1/2" input shaft.

Click the link to add information to this solution:
Your combo kits don't specify whether they are standard NEMA motors. I need Nema 34 with a .375 shaft diameter. Which 3 axis kit work for these requirements?

Yes, you can use the 4 axis kit and use two of the motors on the gantry. You will need to wire the gantry axis motors to the same step and direction signals on the controller interface. For example, if the gantry axis is the X axis, then on the controller step and direction terminals (CP and CW) is wired to both of the stepper motor drivers for the X axis.

Click the link to add information to this solution:
4 axis kit can I use 2 motors for the gantry with one controller card? or I buy the 3 axis kit instead?

We have a redLeaf and redSprout system available which has all of the CNC electronics and computer system assembled as a plug and play system.

Click the link to add information to this solution:
Can you offer me a combo with motors NEMA17, NEMA23 and NEMA34 and a control box ready for plug and play operation? (this including motor drivers and cables)

To replace all of the electronics for a 4 axis system with all NEMA 34 motors, you will need the following components:

4 NEMA 34 stepper motors:
https://buildyourcnc.com/item/electronicsAndMotors-nema34-651ozin

4 drivers (one driver for each motor):
https://buildyourcnc.com/item/electronicsAndMotors-stepper-driver-6!0a

One controller:
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

24v Powers supply for the controller:
https://buildyourcnc.com/item/electronicsAndMotors-power-supply-24v-1a-dc

2 48V power supplies for the motors and drivers:
https://buildyourcnc.com/item/electronicsAndMotors-power-supply-24v-36v-48v

Click the link to add information to this solution:
what do i need to buy for a complete replacement 4 axis cnc mill nema 34 motors mach 3

You can add a 4th driver to the 36v power supply to support a 4th axis.

Click the link to add information to this solution:
How many drivers can you hook up to your 36v power supply? Want to add a 4th axis.

If you are looking for the drivers to pair with NEMA 34 stepper motors, you can find the 6.0 amp drivers here:
https://www.buildyourcnc.com/item/electronicsAndMotors-stepper-driver-6!0a

The other electronics to send the signals to the 6.0 amp drivers (the control board that operates with the control software) is subject to personal preference, but here they are listed:

Our breakout board (works with Mach3 and LinuxCNC and requires a parallel port on your computer):
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

The PoKeys57CNC (works with Mach3 and Mach4):
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Generic USB breakout board (works with Mach3):
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Additional Information:
Do I need a driver for every motor or can I use one driver for all four motors

Additional Information:
Each motor needs its own driver.

Click the link to add information to this solution:
I HAVE NEMA 34 MOTORS BUT NEED THE ELECTRICAL COMPONENTS DO YOU A KIT WITHOUT INCLUDED?

Sure, our blueChick and blackToe CNC Routers are considered relatively small machines at 1'x3' and 2'x4' respectively. They both use NEMA 23/24 motors. We recommend connecting the machines to either Mach3 or LinuxCNC and come with the necessary interface for either control software. You will need a computer for the control software and if you desire LinuxCNC, you will need a parallel port. Mach3 will accept either parallel port, or USB interface.

Click the link to add information to this solution:
I recently purchased the linksprite cnc engraving router and was wondering if your 3 axis small kit would be ok? the engraver came with nema 17 motors and a arduino board but but not liking the grbl control. could you point me in the right direction .Thanks.

We attempt to provide as many services as possible to fit the needs of the CNC community. For a quote on a custom job, please email customerservice@buildyourcnc.com and we will be happy to assist you.

Click the link to add information to this solution:
I bought longs motor nema 34 stepper motor with 4 powers supply and dm860 from ebay, would you be interested in doing all the wiring for me? I pay you for you time

If you are looking for the drivers to pair with NEMA 34 stepper motors, you can find the 6.0 amp drivers here:
https://www.buildyourcnc.com/item/electronicsAndMotors-stepper-driver-6!0a

The other electronics to send the signals to the 6.0 amp drivers (the control board that operates with the control software) is subject to personal preference, but here they are listed:

Our breakout board (works with Mach3 and LinuxCNC and requires a parallel port on your computer):
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

The PoKeys57CNC (works with Mach3 and Mach4):
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Generic USB breakout board (works with Mach3):
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Additional Information:
Do I need a driver for every motor or can I use one driver for all four motors

Additional Information:
Each motor needs its own driver.

Click the link to add information to this solution:
I have Nema 34 motors but I need the electrical components do you have a kit without motors included?

Polabs prepared step by step user guide for PoKeys57CNC and Mach4 to try answering such questions. It is available in our downloads section: https://www.poscope.com/wp-content/uploads/downloads/Pokeys/LibrariesAndPlugins/Mach4 and PoKeys57CNC - step by step guide.pdf

Additional Information:

Click the link to add information to this solution:
Using the PoKeys57CNC how to you connect two motors to the Y axis and how is Mach 4 configured for this?

Are you looking for replacement motors?

Click the link to add information to this solution:
I have a 4' X 8' table with carriages that use nema 23 motors. I have a hypertherm 45 plasma cutter. I have 20 degree 20 pitch rack gear. Can you suggest a plug and run system that I can use for cnc plasma and cnc routing?

Our MAch3 USB interface boards can be located here:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
I AM INTERESTED IN THE 3 AXIS COMBO USB OPTION. NOTICE YOU ENDORSE PLANET-CNC FOR USE WITH THIS BUT WILL MACH3 INTERFACE WELL BEAK OUT BOARD?

Our electronics kits with the parallel breakout board will work with Mach 4, however you will need to purchase the Legacy Driver for Mach 4 to work with our breakout board.

Click the link to add information to this solution:
I have a 3 axis combo w/ parallel breakout board. Will this work with Mach 4?

In our 3-Axis electronics kit, the power supply's provided are capable of both 110V-220V. You have the capability to switch between both in case you might decide to run 220v in the near future or will relocate where 110v is being used.

Additional Information:
Connect spindle to the board



Additional Information:



Additional Information:

Click the link to add information to this solution:
Does the power supply in the "3 Axis Electronics Combo (Small Motors)" have a 220V input option?

The Mach3 USB interface card uses 5V (powered from the computer's USB) and a 24v to power the inputs, outputs and spindle control

the mach3 usb interface can be found here:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

But the mach3 usb does not absolutely need the 24V supply. The 24v supply is only needed if you will be using limit switches (I1-4), VFD controlled automatically and for use with the outputs (O1-4)


Additional Information:
The 36v 8.8 amp power supply we typically recommend is for powering the stepper motor drivers.

Click the link to add information to this solution:
Can I power the Mach3 USB interface 24V with a 48V power supply?

Yes, with caveats. This kit includes a controller that will not be compatible, but if you use another type of controller that has web based control, you can use these electronics. Here is a list of web based control for CNC:

- Easel: The web-based software from Inventables can be accessed through Safari or other macOS-compatible web browsers.

- bCNC: A Python-based GRBL CNC command sender, although you may need to jump through some hoops to get it to run on macOS.

- Universal Gcode Sender: A Java-based software that should run on macOS if you have the Java Runtime Environment installed.

- CNCjs: Another web-based interface that you can run on macOS using Node.js.

Click the link to add information to this solution:
[50] Is there a software control package that will work with Axis Electronics Combo (For Heavy Gantry) for apple os.

When connecting our power supply, no matter if it is 24 or 36 volts with our drivers/motors, you should always use bipolar parallel. This will allow you to have the best torque at higher speeds.

Click the link to add information to this solution:
I have your nema 24 motors using the 36v power supply. Should I use the Bipolar series for the wiring the motors since I am using the 36 volt ad not a 24v power supply?

Yes, we honor a one year warranty on the NEMA 34 651 oz-in stepper motor.

Click the link to add information to this solution:
Is there a warranty on the NEMA 34 651 Oz-in stepper motors you sell?

yes, you can add a 4th axis to the 3 axis system in the future. The entire selection of CNC electronics sold here are modular in nature.

Click the link to add information to this solution:
Can i add a 4th axis in future to you 3 axis system kit?