In our 3-Axis electronics kit, the power supply's provided are capable of both 110V-220V. You have the capability to switch between both in case you might decide to run 220v in the near future or will relocate where 110v is being used.

Additional Information:
Connect spindle to the board



Additional Information:



Additional Information:

Click the link to add information to this solution:
In the 3 Axis Electronics Combo, what is the AC input of the power supply (110v or 220v??). is it possible to specify a certain voltage when ordering?

The 651 oz/in NEMA 34 stepper motor does have a dual shaft. The shaft extends 19 mm at both ends.

Click the link to add information to this solution:
in the 3 Axis Electronics Combo (For Heavy Gantry) the 651oz motor is a dual shaft ?

Here is a list of the parts needed to get the electronics combo functioning (parallel or USB interface options):

- 22 or 24 gauge stranded hookup wire to connect all of the drivers to the USB or parallel interface (terminal to terminal connections),
- 18 gauge stranded hookup wire to connect the drivers to the power supply,
- a power cable (extension cord) to connect from the power outlet to the power supply,
- 4 conductor cable to connect the drivers to the stepper motors,
- a USB cable to connect from the computer to the USB interface (or for power to the parallel interface),
- for the parallel interface, a parallel cable is needed (male to male db-25),
- a computer (for parallel interface, the computer will need a parallel port and if the computer does not contain a parallel interface, the motherboard may have a header for it, or you can purchase a parallel adapter to plug into the motherboard, very inexpensive),
- cnc control software: for the USB interface, you will need planet-cnc software, for the parallel interface, you can use any industry standard cnc control software (the typical is Mach3 for Windows, or EMC2 or Linuxcnc for Linux (Linuxcnc.org).

5v power supply is not needed. The 5 volts signal level power is derived from the computer through USB on both types of interfaces.

Click the link to add information to this solution:
What else to I need to purchase along with the "3 Axis Electronics Combo w/ USB Interface Board" to get the electronics up and running? (software, 5V power supply, 4-conductor wire, etc.)

The plug and play system does have enough memory for additional software. The redLeaf comes standard with a 1TB hard drive.

Click the link to add information to this solution:
DOES THE PLUG AND PLAY ELECTRONICS COMPUTER FOR 3 AXIS CNC MACHINE HAVE ENOUGH MEMORY RAM ADDITIONAL SOFTWARE (BOBCAD-CAM, BOBART, MACH3) TO BE ADDED FUNCTION WELL?

Controlling a 3-axis or 4-axis motor configuration, you will need the following items drivers/motors/controller. Our electronics combo comes with the items mentioned and with power supply/miscellaneous items.
The only other item needed will be a computer (with controller software) to communicate and view controls of your motors.
Using the Parallel breakout board will use Mach 3 software, and USB will use Planet-CNC software.

Additional Information:
You can use this link to see the videos on how to connect the electronics together and make them work: https://www.buildyourcnc.com/tutorials/tutorial-Electronics-USB-Interface-Wiring

Click the link to add information to this solution:
hey, where can i see the steps how can i control 3 or 4 step motor? can i use the Axis Electronics Combo? or i need to connect controller?

Yes, with caveats. This kit includes a controller that will not be compatible, but if you use another type of controller that has web based control, you can use these electronics. Here is a list of web based control for CNC:

- Easel: The web-based software from Inventables can be accessed through Safari or other macOS-compatible web browsers.

- bCNC: A Python-based GRBL CNC command sender, although you may need to jump through some hoops to get it to run on macOS.

- Universal Gcode Sender: A Java-based software that should run on macOS if you have the Java Runtime Environment installed.

- CNCjs: Another web-based interface that you can run on macOS using Node.js.

Click the link to add information to this solution:
[50] Is there a software control package that will work with Axis Electronics Combo (For Heavy Gantry) for apple os.

The electronics packages come with standard stepping motor drivers, stepping motors, power supply (36v and 8.8amps), and a breakout board (USB or parallel, depending on the option you select). The USB will not work with linuxcnc, but the parallel breakout board works fine with linuxcnc. All of our drivers work well with the linuxcnc software. We use this software with some of our machines and we also sell the CNC electronics / computer system (redLeaf and redSprout) with linuxcnc installed and tested (if the customer selects linux over windows or requests a dual boot system).

Click the link to add information to this solution:
May i have more detailed Information aboute the 4 Axis Electronics Combo? We're using EMC2 and i wanna check compatibility first before I'll buy some. https://www.buildyourcnc.com/Item/electronicsAndMotors-4axis-425-elcombo

Our electronics contains a switchable power supply that allows you to switch the input mains voltage between 115 volts (110/120) and 230 volts (220/240). the hertx range is not specified, but there are capacitors to smooth out standard frequencies to enable DC output.

Click the link to add information to this solution:
hi, what about, if I buy from you some elecronic parts like (3 Axis Electronics Combo) and I use them here in france , where the electric voltage is 220V 50Hertz ? thats gonna works? thanks

These boards are compatible with Mach3 only at this time. We will be adding a Mach4 board in the near future.

Click the link to add information to this solution:
Are the 3 axis electronics combos with the Mach 3 USB breakout board compatible with Mach 4?

Did you connect the USB connector to the breakout board?

Additional Information:
YES I CONNECTED THE USB TO THE BREAKOUT BOARD

Click the link to add information to this solution:
I connected the electronics (for 2 x 4 feet) that I ordered from you. But how do I check if I connected all the wiring properly. There is neither any light on motor drivers nor on breakout board. And the motor shaft also does not move before and after the power supply is given.

Make sure all your bolts/screws are tighten correctly and if using a lead screw make sure your anti-backlash nut is not offset. Now a default setting will be 10101100 for your driver dip switch settings and in motor tuning (mach3) 1600 steps per, 400.02 velocity, 4 in acceleration. now the acceleration and velocity can be adjusted to move your machine faster, but if set to high they could stall. Make sure you have the correct wiring from your motor to your driver (https://www.buildyourcnc.com/Documents/PN.SM60HT86-2008BF-U%20(inhouse%20PN.60BYGH303-13)%20(1).pdf).

Click the link to add information to this solution:
I have your Nema 24 electronics kit and am having problems with the Z axis dropping over time. I am using a PC 8902 motor. Any ideas on what the problem is? What should be the motor tuning values in Mach3? Thanks

Yes, the 651 oz/in motor requires a driver that is compatible to the motors (the motor will draw 6 amps max and the driver paired with this motor will be able to allow for a 6 amp draw). I would also recommend a 36 volt power supply for better high velocity performance.

Click the link to add information to this solution:
I HAVE ONE OF YOUR SMALLER STEPPER MOTORS RUNNING MY X AXIS BRIDGE CRANE AND IF IT IS MOVED TO FAST THE MOTOR SOUNDS LIKE SKIPPING STEPS WILL 651OZ REQUIRE A DIFFERENT POWER SUPPLY CONTROLER?

Our MAch3 USB interface boards can be located here:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
I AM INTERESTED IN THE 3 AXIS COMBO USB OPTION. NOTICE YOU ENDORSE PLANET-CNC FOR USE WITH THIS BUT WILL MACH3 INTERFACE WELL BEAK OUT BOARD?

Here is a list of the parts needed to get the electronics combo functioning (parallel or USB interface options):

- 22 or 24 gauge stranded hookup wire to connect all of the drivers to the USB or parallel interface (terminal to terminal connections),
- 18 gauge stranded hookup wire to connect the drivers to the power supply,
- a power cable (extension cord) to connect from the power outlet to the power supply,
- 4 conductor cable to connect the drivers to the stepper motors,
- a USB cable to connect from the computer to the USB interface (or for power to the parallel interface),
- for the parallel interface, a parallel cable is needed (male to male db-25),
- a computer (for parallel interface, the computer will need a parallel port and if the computer does not contain a parallel interface, the motherboard may have a header for it, or you can purchase a parallel adapter to plug into the motherboard, very inexpensive),
- cnc control software: for the USB interface, you will need planet-cnc software, for the parallel interface, you can use any industry standard cnc control software (the typical is Mach3 for Windows, or EMC2 or Linuxcnc for Linux (Linuxcnc.org).

5v power supply is not needed. The 5 volts signal level power is derived from the computer through USB on both types of interfaces.

Click the link to add information to this solution:
I've built a router frame, so I need electronics. I'm buying 2 NEMA 34s and 1 NEMA 23. Can I get a list of controller, power supply and related components so I can get them as I can afford them? Please.

The 5V power required for the breakout board can be a simple USB male to male cable, that will connect from your computer to the board itself.
Now adding a external power supply make sure that it does not exceed a total of 5V and the standard 500 MilliAMP - 1 A.

Click the link to add information to this solution:
I have a YDH-18-5 Power Supply AC Input:100-240v 47-63Hz, Ouput: 5v - 2A and need to know if its safe to use with the Parallel Breakout Board.

You can find the datasheets to our motors be going to the the stepping motor category page https://www.buildyourcnc.com/category/nema and selecting the motor. This will bring you to the product page for the motor and all of the motor information will be found there.

Click the link to add information to this solution:
I would like to design my own CNC router around one of your electronics bundles, either the 3 Axis - Heavy Gantry or 3 Axis - All Large Motors. Do you have the data sheets for the motors so that I can use the dimensions in my model?

I have very detailed wiring videos for the Pokeys57CNC controller on the pokeys57CNC controller webpage: https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
[50] I purchased 3 Axis Heavy Gantry Electronics /w Pokeys57CNC controller (Mach3 and 4 Compatible) and Cable Pack I plan to use Mach 3 do You have a wiring diagram Thanks

The 12V power supply has 3 terminals for AC in: N, L and earth ground. The output of the 12V power supply has 2 DC + and - terminals. Cut the connectors off of the ends of the fan and pump wires. Strip the red and black wires of both units. The fan will connect to the 12V power supply red to the + and black to the -. The pump will connect in the same way, but the white is not connected.

If you have a pump that has a grey and black wire on the large connector, the grey is the 12VDC V+ wire and the black wire goes to the V-. The extra wire does not need to be connected.

Click the link to add information to this solution:
THE GANTRY MOUNTED SPINDLE WATER COOLER PUMP THAT I PURCHASED DOES NOT OPERATE NO MATTER HOW CONNECT THREE WIRES TO TWO WIRE POWER SUPPLY.

The 2.2kW spindle will have the same amount of torque and strength using either the 110V or the 220V inverter. Nothing will significantly change in either application since the 110V inverter has a small step up transformer which will increase the voltage from 110V to 220V to run the spindle efficiently.

Additional Information:
I'd like confirmation on this -- isn't there a cost in efficiency to having the 110v step up to 220v?

Additional Information:
Thank you so very much for explaining this!!! I truly appreciate your help! Tricia

Additional Information:
Thank you so very much for explaining this!!! I truly appreciate your help! Tricia

Additional Information:
Thank you so very much for explaining this!!! I truly appreciate your help! Tricia

Additional Information:
Thank you so very much for explaining this!!! I truly appreciate your help! Tricia

Additional Information:
Thank you so very much for explaining this!!! I truly appreciate your help! Tricia

Click the link to add information to this solution:
Good morning, I would like to know if the strength of the 2.2kw spindle is weaker when using the 110V version of the VFD. Does it have the same power as the 220V version VFD?