All of our CNC machines can cut melamine. If your application (kitchen doors) requires large cutting area, then I would recommend the following machines:

- greenBull 4x (4'x8'), 5x (5'x10') or 6x (6'x 12')

- greenLean 4'x8' vertically oriented CNC machine

- Or our Fabricator Pro 4'x8' metal CNC machine

Click the link to add information to this solution:
CAN YOU RECOMMEND WHICH CNC MACHINE TO GO WITH FOR CUTTING MELAMINE AND MAKING KITCHEN DOORS FROM MDF. ALSO DO PROVIDE TRAINING ON OPERATING SETTING UP SHOP PRODUCTION USE? THANKS

No, ground from the pokeys57cnc controller should not be required. Your VFD should have two terminals that will turn on and off the spindle (forward, or stop). These two terminals simply need to be connected to each other to invoke that operation. In the VFD manual, you will see a schematic with a normally open switch symbol between these two terminals. The onboard relay on the pokeys57CNC would be a great feature of the board to connect to the two terminals of the VFD.

Click the link to add information to this solution:
I have a Glack CNC motor and VFD and confused if a ground from the Pokeys57 needs to be ran to the VFD to turn on and off the motor and to also control the speed. I can provide a picture

All of our CNC machines can cut melamine. If your application (kitchen doors) requires large cutting area, then I would recommend the following machines:

- greenBull 4x (4'x8'), 5x (5'x10') or 6x (6'x 12')

- greenLean 4'x8' vertically oriented CNC machine

- Or our Fabricator Pro 4'x8' metal CNC machine

Click the link to add information to this solution:
Can you recommend which CNC machine to go with for cutting melamine and making kitchen doors from MDF. Also do you provide training on operating and setting up machine for shop production use? Thanks

Polabs prepared step by step user guide for PoKeys57CNC and Mach4 to try answering such questions. It is available in our downloads section: https://www.poscope.com/wp-content/uploads/downloads/Pokeys/LibrariesAndPlugins/Mach4 and PoKeys57CNC - step by step guide.pdf

Click the link to add information to this solution:
What is the 24VDC Power requirement for the Pokeys47CNC? 1A, 2A? ...I'm running a separate 36VDC PS to the Stepper drivers and a 24VDC PS to the Controller.

CamBam specifically creates the g-code (machining operations) instructions to be loaded into Mach3. Make sure in your CamBam g-code file parameters, you are using the Mach3 post processor. If you have already done this, let me know. If you are not sure how to do this, let me know.

Click the link to add information to this solution:
I am having trouble connecting the cambam program with my Mach3 to my 4X8 Blackfoot CNC machine. Where can I get help on this issue. Have had my machine since 2015 and have not been able to use it. Thank you

Absolutely! You can have almost unlimited limit switches and home switches on this controller. It all comes down to the wiring scheme used. I recommend the home switches be on separate input terminals. For example, IN1 would have the X home switch, IN2 would have the Y home switch and, IN3 would have the Z home switch if you plan on using home switches for the Z axis.

Adding the limit switches, these can be located on any input you want, even on the IN1, 2 or 3. The wiring scheme I like to use is as follows:
- IN1 has the X home, X limit ++, and X Limit --
- IN1 has the Y home, Y limit ++, and Y Limit --
- IN1 has the Z home, Z limit ++, and Z Limit --

In most cases, the Limit -- is the same switch as the Home switch.

These can be wired as NC (Normally closed) as a serial scheme, or as NO (Normally open) as a parallel scheme.

To understand the limits and wiring schemes, check out this video:

Click the link to add information to this solution:
[575] Hi, for the manage the limit switches, is it possible to have, for example, the same limit switch for X-- and X homing? And what is the configuration in mach3? In my CNC machine they are in the same position. Thank you

I would suspect that the velocity and/or acceleration is too high for the amp setting on the driver. Consider increasing the current amp setting on the driver is the motor can handle the current, or decrease the velocity and/or acceleration.

You might also want to check to see if you have any mechanical binding on the machine. To check, remove the mechanical drive mechanism so the axis slides freely and slide it from end to end to feel if you have any tight areas or binding.

Additional Information:

Click the link to add information to this solution:
My stepper motors are randomly and frequently stalling while using the Pokeys57CNC controller board, any idea what could be the issue?

Attaching two motors in parallel is possible, but you will need another motor and driver for the opposite side. Each motor must have its own driver to work accordingly and fluently. The two can be wired together, to the same pins on your breakout board and set the dip switches on the driver to match the ones on your x-axis(ex). But remember to view the orientation of the motor and which way it spins, since it is on the opposite side it will have to be orientated correctly to move in sync with the other motor.

Click the link to add information to this solution:
I just finished building my first CNC with the electronics I purchased from you and I am already thinking about improving it. I would like to build a 2 motor X axis solution. Is it possible to attach 2 parallel motors and drivers to the BlueBrew Breakout Board? If so, how?

The following videos are helpful when connecting the VFD to a pokeys57CNC controller; however, there is useful information on the external terminals of the VFD and how to connect the VFD to any controller using a relay. Additionally, the videos have useful information on how to program the VFD.

Start and stop for spindle
https://youtu.be/0SLFuM4tzuU

Speed control:
https://youtu.be/pA69t1ZLY2s

The following video uses the Mach3 usb controller to control a spindle.

Click the link to add information to this solution:
Do you have a diagram on how to connect the vfd so the CNC controller box can turn the spindle on and off whenever i start a job?

You can use the Pokeys57CNC board with our 3.0 amp drivers. The Pokeys57CNC has all of the headers necessary to provide the pulse train to any common stepper driver.

Here is the link to the Pokeys57CNC interface board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Here is the link to the 3.0 amp stepper motor driver:
https://www.buildyourcnc.com/item/electronicsAndMotors-stepper-driver-3!0a

Click the link to add information to this solution:
I'm planning on using your 425 oz motors and need help on selecting the right interface and driver boards. The PoKeys57 CNC USB card looks good but I wonder if the 2.5 amp driver boards shown with it are enough for the 3 amp motors?

Dealing with our inverters, they are built with a bit of margin on the input power. For our 220V VFD the margin is from 170-250V 50/60Hz, so running our VFD in your location will not be an issue! Our electronics will not have a issue running at 230V as well.

Click the link to add information to this solution:
Hello. I am interested in the green bull 6X long z CNC machine with electronics. I live in NZ, where the voltage is 230 V and 50 Hz. is it going to be possible to get the inverter to run here? Thanks!

All the options for and variations of our blackTooth laser cutter/engraver are available on our website here https://buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx#prettyPhoto. The wiring diagram is available here: https://buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx#prettyPhoto/0/
We do not offer plans or a bill of materials for our machines at this time, but if you are interested in doing your own from scratch you can learn a lot about the design and build process from our tutorials. We wish you success in your endeavors.

Click the link to add information to this solution:
How can i get a complete list of all the components (electronics) I need for a CNC laser cutter with the laser controller? A wiring Diagram would probably be very helpful.

No, the 3.1 version will not support slaving the X axis. You will either need to wire the two x axis driver to the same X signal pins, or use the DDCS v4.1 which does support slaving an axis.

Click the link to add information to this solution:
[823] I plan to use a DDCS stand alone controller for a CNC router build which will have two stepper motors on the x axis, one on Y and one on Z. Will the 3.1 version handle two motors synched on the X axis or will I need the 4.1 version?

I would not recommend slaving an axis using the method of taking an additional axis from the USB interface. Instead, wire both drivers to a single axis on the USB interface. This will insure perfect signal output to both drivers. If you requre the motors to spin in opposite directions, simply wire one of the motors to the driver reversing the coil A and B connections, or use a hex inverter (https://www.buildyourcnc.com/tutorials/Tutorial-Two-Motors-Spinning-Oppositely-On-Single-Axis).

Click the link to add information to this solution:
I purchased a USB Breakout board, motors and drivers, paid for CNC USB Controller Software and I CAN NOT "Slave" an axis, but there is an option to do that. The moment I connect USB Breakout Board "Slave" option becomes shaded and I can no longer select it (becomes not functional). What is going on? Need help asap. Thanks

Absolutely, I can answer this type of question and anything other questions you may have with your new-to-you CNC router.

Additional Information:
20

Click the link to add information to this solution:
[789] Can you help me with selecting a power supply ( and a few other components ) for the stepper motors that came with a homemade CNC Router I just purchased.

Recommend first test to check a non-working axis, is to connect the current working axis(ex X-axis) to either the y/z axis to test the actual board and wiring in other axis setup. If tests failed and working (x-axis setup) does not working in the new axis location, go the Planet-CNC/File/Settings/Axes and check if your current non-working axis setup requires a inverted pulse. Check box and test again.
Next test if first fails, is to check continuity in your wires. A simple multimeter(ohm's) will work, just connect the positive and negative ends to one side of the same wire and if reading comes to 0.000, wire has continuity and if reads 0.L then there is a break in the wire and should be replaced.

Click the link to add information to this solution:
I installed the USB CNC Planet and got out of your USB controler $ 75 .Viska have linked to a video 'Party - 2.. X - running and y and z-axis does not work, it moves step motors and controller positions X -axis works, and Y and Z does not work.

The PlanetCNC USB software, like most machine control software, can be used to control a laser engraver/cutter. The typical modification is to use the Z axis down signal to fire the laser, analogous to an endmill cutting into the workpiece from an initial position above it.

For the second question, it is important to note that BYCNC machines are not based on PlanetCNC software, or any other particular machine control system. The machines themselves will accept standard signals from a wide variety of machine control systems, not just PlanetCNC or Mach3. This allows maximum flexibility for the customer to choose their own preferred software for this part of the toolchain.

That said, our machines will accept a laser head either in lieu of or in addition to a spindle. Here is an example of a combination spindle/laser mount for our greenBull machine: https://buildyourcnc.com/item/cnc-machine-laser-spindle-combo-head. We have all the parts you would need to add laser functionality to your machine here: https://buildyourcnc.com/LaserComponents.aspx, if you feel comfortable assembling your own package. Also, feel free to contact our sales department for a quote if you need a custom assembly.

Click the link to add information to this solution:
Can the Planet CNC USB controller be used with a laser engraver/cutter? Can the build your own CNC based on the Planet CNC USB controller accept a Laser head instead of a router?

At this time we are working to release a new USB controller board that will be compatible with Mach4 software and do not have any immediate plans to update the Planet-CNC USB board.

Click the link to add information to this solution:
Are there plans to release a USB Controller to work with the Planet CNC Output Board for more advanced spindle control from within Planet CNC?

You will need to build the table unit for your machine. There are instructions on how to do this at the bottom of the product page here, https://www.buildyourcnc.com/Item/cnc-machine-blackFoot-v4
There is no estimate on how much this will cost though, since there are too many variables involved to do this.

- PC with parallel port and USB port
- 20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
- 18awg stranded wires for power supply to drivers
- 24awg stranded wires for breakout board to drivers
(location and spacing of components varies from one person to another, so we do not provide cables/wires)
- General purpose extension cord (cut the female end off) to provide power to power supply
- USB cable to power breakout board
- Parallel cable to communicate to breakout board
- Router
- (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
- (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
- End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
- CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
- CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx

This answer is applicable to most of our machines with the exception of the greenLean and the blueChick since those machines are equipped with a table structure.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Can I purchase a computer off Amazon (I have a machine I want to use) and still use the USB interface to drive it with LinuxCNC?