Did you look at the g-code instruction during the pause? There could be a dwell operation. Also, take a look at the status bar next to the reset button. There is information at that location that may be helpful.

Click the link to add information to this solution:
What causes the cnc machine to stop/pause a second, or 2, in the middle of operation

Dealing with a mid-stop cut via Mach3, you will have to be careful if it is intentionally or unintentional. If you desire to stop your machine while in the middle of a cut be sure to stop it when the machine is moving in an upward motion on the z-axis and the X/Y-axis are stationary. Then you can choose the point (G-code) where the machine was left off and click on the Run from here button on the Program Run screen (left hand side) right above the Reset button.
(Make sure spindle/router is running before hand!)

Now if the machine stops unintentionally, and was moving in either the X/Y-axis, then it will be difficult to run the machine from the original point dealing with the coordinates might have been lost due the the machine continuing motion but via Mach3 the machine has stopped.

If this occurs to fight this issue before hand, is marking your home with the spindle/router to make a hole were your home is. Although moving it manually back to home the machine can be off by the smallest amount and could cause an inconsistent cut. If accuracy is something that can not be risked, then you can home the machine about a 1/4" or 1/2" down from the original home to start your cut on the same material but loosing that small piece.

Additional Information:


Additional Information:
My typical go to solution is:

- Note the current g-code line where the machine stopped.
- If Mach3 errored and you cannot control the machine, Exit Mach3 - you may find that reset, stop does nothing to stop the spindle. When you exit mach3, the spindle will stop automatically.
- Restart Mach3. The DRO (Digital Readout) should show the correct coordinates where the machine position was before exiting Mach3.
- Scroll to the g-code line where the machine stopped. You may need to go a few lines prior to make sure you are not skipping any machining operations (which is why it is a good idea to learn the basics of g-code - don't worry, it's easy)
- Click on the "Run from Here" button.
- Mach3 will present you with a "Preparation Move" dialog box with the location that it will move to. If the coordinates shows a position that is into the material, make sure to specify a rapid height (clearance height) so the machine will move up first and then move to the location before moving down into the material. If the spindle is automatically controlled by Mach3, make sure to check the turn spindle on checkbox. If not, make sure the router or spindle is on before clicking OK.

Additional Information:
My cnc router stops at gcode line 50,000 and cannot finish program. They are about 150k of lines total. I have Mach3 and have bought the additional line capability. Is 50,000 (or around that) the limit? Is Mach 4 hobby license better and in what ways? Thanks! Mike Huber

Additional Information:
If you have a license for Mach3, then you should be able to run g-code indefinitely. I think there is something else going on.

Additional Information:
Additional Information:
If you have a license for Mach3, then you should be able to run g-code indefinitely. I think there is something else going on.
What else could be going on?

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:
41PBGevE

Additional Information:
-1 OR 2+358-358-1=0+0+0+1 --

Additional Information:
-1 OR 2+69-69-1=0+0+0+1

Additional Information:
-1 OR 2+69-69-1=0+0+0+1

Additional Information:
-1' OR 2+902-902-1=0+0+0+1 --

Additional Information:
-1' OR 2+902-902-1=0+0+0+1 --

Additional Information:
-1' OR 2+730-730-1=0+0+0+1 or 'Qb1SuH5C'='

Additional Information:
-1" OR 2+161-161-1=0+0+0+1 --

Additional Information:
-1 OR 2+69-69-1=0+0+0+1

Additional Information:
if(now()=sysdate(),sleep(15),0)

Additional Information:
0'XOR(if(now()=sysdate(),sleep(15),0))XOR'Z

Additional Information:
0"XOR(if(now()=sysdate(),sleep(15),0))XOR"Z

Additional Information:
(select(0)from(select(sleep(15)))v)/*'+(select(0)from(select(sleep(15)))v)+'"+(select(0)from(select(sleep(15)))v)+"*/

Additional Information:
(select(0)from(select(sleep(9)))v)/*'+(select(0)from(select(sleep(9)))v)+'"+(select(0)from(select(sleep(9)))v)+"*/

Additional Information:
(select(0)from(select(sleep(15)))v)/*'+(select(0)from(select(sleep(15)))v)+'"+(select(0)from(select(sleep(15)))v)+"*/

Additional Information:
-1; waitfor delay '0:0:15' --

Additional Information:
-1; waitfor delay '0:0:19' --

Additional Information:
-1); waitfor delay '0:0:15' --

Additional Information:
-1)); waitfor delay '0:0:15' --

Additional Information:
1 waitfor delay '0:0:15' --

Additional Information:
O6enxjIS'; waitfor delay '0:0:15' --

Additional Information:
0MgObbnm'); waitfor delay '0:0:15' --

Additional Information:
8dan23Sv')); waitfor delay '0:0:15' --

Additional Information:
-5 OR 898=(SELECT 898 FROM PG_SLEEP(15))--

Additional Information:
-5 OR 353=(SELECT 353 FROM PG_SLEEP(19))--

Additional Information:
-5) OR 539=(SELECT 539 FROM PG_SLEEP(15))--

Additional Information:
-1)) OR 919=(SELECT 919 FROM PG_SLEEP(15))--

Additional Information:
xjpbAodW' OR 81=(SELECT 81 FROM PG_SLEEP(15))--

Additional Information:
r6v9pPjr') OR 551=(SELECT 551 FROM PG_SLEEP(15))--

Additional Information:
RDopsUKk')) OR 996=(SELECT 996 FROM PG_SLEEP(15))--

Additional Information:

*DBMS_PIPE.RECEIVE_MESSAGE(CHR(99)||CHR(99)||CHR(99),15)

Additional Information:

'||DBMS_PIPE.RECEIVE_MESSAGE(CHR(98)||CHR(98)||CHR(98),15)||'

Additional Information:
1'"

Additional Information:
1����%2527%2522

Additional Information:
@@HCYaP

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
USING MACH3, MY MACHINE STOPS IN THE MIDDLE OF A PROJECT. HOW CAN IT BE STARTED AGAIN FROM POINT STOPPED?

You can determine if the country is serviceable by:
- selecting the items you want to purchase on the website
- go to the cart (shopping cart top left of any webpage)
- log in, or register
- Enter the address and click on calculate shipping.

The webpage will return the direct rates and whether your area is serviced or not. Feel free to enter any address as long as you are able to receive the package from that address.

The shipping times are determined by the service you select in the shopping cart. If a machine is purchased, we generally have a one week lead time unless otherwise stated in the description of the machine's product page.

Additional Information:

Click the link to add information to this solution:
What is your shipping costs for the greenLean CNC machine to Perth Western Australia

You can determine the cost of shipping the greenLean or any other product to your country by adding the greenLean option to the cart. In the cart, click on the calculate shipping button and the shipping costs will be presented directly from the carriers that we use. You will also see the number of packages and weights of the packages in the cart, under the items in smaller print. Make sure that your shipping address is entered in the form prior to clicking on the calculate shipping button.

Click the link to add information to this solution:
I am looking at the greenLean cnc machine 4'x8' Vertically Oriented CNC. I am based in the UK. What sort of shipping costs would we be looking at?

If one of your stepper motors decides to stop moving and the others are moving during a CNC milling or laser cutting job, then there could be two things that could be causing this.

- The motor found its limiting torque (usually comes with a not-so-pleasant sound). This is where the control software is trying to move the stepper motor too fast (velocity, or too fast too quickly, acceleration) and the load against the stepper motor (inertia of the machine, or the material against the end mill while milling). Recommended action is to lower the velocity and/or acceleration, and/or lower the feedrate when cutting.

- There is a wiring issue with the wiring from the driver to the motor. This could be a loose wire, or a chafed wire (or two shorting together). It can also be a loose digital wire from the controller board to the driver. Sometimes wire ties can be the culprit. Recommended action would be to thoroughly inspect the wiring.

It's probably not the limit switches since that would cause a stop to the entire motion of the cnc router or laser machine.

Sometimes Mach3 will show a status when something goes wrong, but in cases where the motor is stopping due to its torque limit, then that would not be shown in the status. It's always good to check it anyway.

Additional Information:
I need to clarify my situation a little better after going to my shop and trying to run another program on Mach 3. About 15 minutes into the milling process all the motors (2-X axis, Y axis and Z axis)stop but the program continues to run. I stop the program and after a couple of minutes when I try to restart the program all the motors start working again. Then after another 15 minutes or so, all the motors stop again. I checked and rechecked my wiring. This has never happened to me before when running the same programs with the same setups and motor speeds. All of a sudden when I reloaded a program I successfully used before it does this. Do you have any recommendations?

Additional Information:
Yeah, it sounds like a more complex issue. Have you tried running in the air without using the spindle. This may be a power related issue.

Additional Information:
That's exactly what I did. I ran the program without the router motor on just to see if the motors would get through the whole program but they stopped working after about fifteen minutes and then I was able to start them again after about 3 or 4 minutes. I never had this problem before so you can imagine my frustration especially after ruining a couple of projects on expensive material.

Additional Information:
Sure. I can completely understand. Try this: disconnect all but one of the driver from power and digital connection and do the air run. Repeat this for each driver and note your findings. This will rule out the drivers causing a power failure.

Also, is your stepper motors and drivers on a separate power circuit from the computer?

Additional Information:
I will try disconnecting each driver and digital connection, which will be a real pain because it will be hard to access.

All the stepper motors, drivers and computer are plugged into the same power strip.

Additional Information:
Ok, so there is no power failure going on, but I believe it is necessary to test each stepper motor and driver pair individually. Hopefully that will lead to a conclusion.

Additional Information:
It will take a little time but I will do it and report back on my findings.

Additional Information:
Curious, what machine is exhibiting this problem?

Additional Information:
I purchased a BYCNC kit back in 2009 with an approximate cutting area of 2' X 4'. I later changed out the Z-Axis Motor and controller for a larger one and have two X-axis motors and controllers. In 2010 I rebuilt the machine out of birch plywood instead of the particle board that the kit supplied. I sent Patrick pictures to him. The machine never gave me a problem till now.

Additional Information:
Thanks for the update. This is Patrick by the way. I answer pretty much all of the Customer Service questions. That machine has given quite a good history.

Additional Information:
I love the machine and made a number of samples of my work for my e-commerce site, but I can't start selling product until I know this problem is solved because I will not be able to fulfill orders. I finally got all the electronics out of its enclosed protected area near the machine so that I test each controller as you recommended. I hope the problem can be rectified. Will let you know.

Additional Information:
Thanks.

Additional Information:
I tested each stepper motor and driver pair individually and they worked so what might be the next step?

Additional Information:
Did each stepper motor driver pair work for the full +15 minutes?

Additional Information:
Yes, I had them in operation for over 30 minutes.

Additional Information:
Ok, well it’s good that the motors and driver are ok. We are now down to the power supply and the breakout board as possible causes for the stop. I have a feeling it may be the power supply where with all three drivers drawing current and the power supply maybe getting too hot. Is the fan in the power supply working? You can also test to see if there is 36 volts on the power supply voltage output (V+ and V-).

Regarding the breakout board, if you have an oscilloscope, you can test if the driver pulses are outputting, but I would consider this as a last resort after you determine if there is a problem with the power supply.

Additional Information:
I tested the power supply with a voltmeter and each output was registering 39-40 volts. I think the problem may be the g-code. I am using V-Carve pro to do design and output to Mach 3 Mill g-code. When I studied the g-code lines I noticed that further into the program the z-axis g-code stopped zeroing out to move to the next part of the carving. In other words both the x and y keep moving and the z just stopped working because there was g-code missing. I think something is missing when the design was converted to g-code. I noticed that when I ran a simpler project it worked without problems so I need to investigate this further.

Additional Information:
New Update, Its not the g-code. I started to run the long program and everything was working fine until about 45 minutes into it, all the motors stopped working (but the program was still running) and there was a high pitched hum. When I put my hands on the motors they were all trying to move but it seemed they were all stalled. I turned the power off, gave it a minute and when I turned it back on I was able to move the motors again. Could this be a power supply problem?

Additional Information:
It does sound more and more like a power supply problem. Did you test the power supply after the motors stopped?

Additional Information:
No, I did not. What should I be looking for.

Additional Information:
It’s good that you know the voltage during normal operation, so you have a base understood. If the power supply is the problem, the voltage will be reduced or non existent when measured after the problem.

Additional Information:
Also, check to see if the fan is running on the power supply when the motors stop. That may (not absolutely) be an indication.

Additional Information:
I'll run another test, check the voltage and fan when the problem occurs and let you know. Thanks for hanging in there with me as we try to resolve the problem.

Additional Information:
It’s my pleasure. This service is rarely used and is faster then email. Odd nobody uses it. Any recommendations you can give would be great. No problem using this FAQ to pose ideas as this resolution will be cleaned up later.

Additional Information:
It might be that people do not realize you can communicate through the sight like this because they are so used to e-mail and texting. You may want to explain this feature in the customer service section.

I ran the program this morning and it did not take long before the motors stopped. While operating the voltages for all three motors was 46 volts, when the motors stalled (and again there was a high pitch hum) the voltage went up to 60 volts and the fan on the power supply was operating.

Additional Information:
So, the driver work individually, but not all together. There is a high pitch sound when the motors fail. You have noted 60 volts from the power supply and the supply fan remains on. This is a difficult issue to resolve, but it seems to me that your power supply may be bad. The 60v measurement tells me that the current dropped and ohms law tells us that is current drops, volts will rise if the resistance stays the same.

Additional Information:
As one last test I am going to test each driver again and let them go through the entire program because it seems that the failure can occur at the beginning or towards the end of the program. When I originally tested ach driver I let them run for about a half an hour and the program takes over an hour to run completely. I just want to make sure that it is not the drivers. I will report back when I finished but as you noted it may be the power supply but I want to make sure.

Additional Information:
That’s a great idea.

Additional Information:
I just ran the x-axis through the whole program and there was no problem especially since I have two NEMA 23 motors moving that axis. Before I check the Y and Z could having a NEMA 34 on the Z axis with appropriate controller be a problem. I used the larger motor on the z axis because the router I am using is a large 1 1/2 hp. I've run this program in the past with this set-up and have not had a problem.

Additional Information:
Having a, say 3.0 amp driver, driving a stepper motor that typically requires a 6 amp driver would not seem to be an issue since the driver is limiting the current draw, but the driver may not be able to handle larger coil and back EMF with the protection on the 3.0 amp driver. With that said, I don’t believe that is the issue in this case.

Additional Information:
I don't either because I was able to run this and other complicated programs with this set-up in the past. I will let you know on the y and z axis.

Additional Information:
Thanks

Additional Information:
I ran the Y axis and z axis separately through the entire program and there was no stopping or problem. I guess the culprit is the power supply and I'll order a new one and hope that resolves the problem.

Additional Information:
Yes, that is the most probable cause. Please keep me informed. Thanks!

Additional Information:
Received and installed the new power supply. I ran the program with the router on and it worked flawlessly. The program runs for an hour and a half and I did not have a single problem. I guess it was the power supply but I was glad to go through all the diagnostics we discussed before replacing it. I hope this power supply lasts a lot longer than the last one. Thanks much for hanging in there with me and coming up with the solution.

Additional Information:
It’s my absolute pleasure and I am so happy to hear that the power supply replacement solved the problem.

Additional Information:


Additional Information:
Y axis stop working X & Z work fine Y axis has two motors have check wiring & connections new breakout board still the same port & Pin set OK dont no were to go next David

Additional Information:


Additional Information:
my cnc plasma cutter will run out the program when cutting. what is the cause?

Additional Information:
The cnc plasma question shod be a separate question. Can you pise that question by clicking the customer service live menu button at the top? Thanks.

Click the link to add information to this solution:
WHAT CAUSES ONE OF MY TWO AXIS MOTORS TO STOP WHILE THE MACH3 PROGRAM IS STILL RUNNING

Our machine that matches those dimensions, the blueChick, uses roller chain for both X and Y axes, and a 1/2" 5 start 10 TPI lead screw for the Z axis. The precision is generally related to repeatability and we have not does extensive measurement of these tolerances. The resolution is set at better than 1000 steps per inch.

Here is the link for the blueChick:
https://www.buildyourcnc.com/blueChickVersion42CNCMachineKit.aspx

Click the link to add information to this solution:
What precision do the CNC machine have, for instance the 12’’ x 36’’ x 3’’?

Other items you will need if you are purchasing the electronic combo (motors, drivers, power supply and computer interface) and the hardware and plans kit:

You will need the wood to create the structure of the machine. You will need a router to serve as the cutting instrument. You will need a computer to control the machine and the software that will serve as the control program. You will also need lead screws and rails (aluminum angles). If you intend to have faster travel than 20 ipm, we recommend purchasing the 5 start lead screws so you can achieve up to 300 ipm. https://www.buildyourcnc.com/item/mechanical-leadscrews-leadnuts-!5-5-starts-10-tpi

Click the link to add information to this solution:
if i purchase the 4 Axis Electronic Combos and the Combo #1 with hardware, plans and DVD what else do i need to have a complete cnc machine

You will need to build the table unit for your machine. There are instructions on how to do this at the bottom of the product page here, https://www.buildyourcnc.com/Item/cnc-machine-blackFoot-v4
There is no estimate on how much this will cost though, since there are too many variables involved to do this.

- PC with parallel port and USB port
- 20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
- 18awg stranded wires for power supply to drivers
- 24awg stranded wires for breakout board to drivers
(location and spacing of components varies from one person to another, so we do not provide cables/wires)
- General purpose extension cord (cut the female end off) to provide power to power supply
- USB cable to power breakout board
- Parallel cable to communicate to breakout board
- Router
- (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
- (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
- End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
- CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
- CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx

This answer is applicable to most of our machines with the exception of the greenLean and the blueChick since those machines are equipped with a table structure.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
IF I PURCHASE A GREENBULL 6X LONG Z CNC MACHINE KIT AND MACH3, WHAT ELSE WOULD BE REQUIRED TO ASSEMBLE THE WORKING MACHINE? HAVE CAD SOFTWARE.

For our greenLean CNC vertical machine, was built and controlled using 2 651-oz in motors/425 oz-in motor.
The 651-oz motors runs both the x/y axis, as our 425-oz motor controls the z axis.

Click the link to add information to this solution:
What size motor is powering the y axis on the greenLean CNC machine?

You will need to build the table unit for your machine. There are instructions on how to do this at the bottom of the product page here, https://www.buildyourcnc.com/Item/cnc-machine-blackFoot-v4
There is no estimate on how much this will cost though, since there are too many variables involved to do this.

- PC with parallel port and USB port
- 20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
- 18awg stranded wires for power supply to drivers
- 24awg stranded wires for breakout board to drivers
(location and spacing of components varies from one person to another, so we do not provide cables/wires)
- General purpose extension cord (cut the female end off) to provide power to power supply
- USB cable to power breakout board
- Parallel cable to communicate to breakout board
- Router
- (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
- (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
- End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
- CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
- CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx

This answer is applicable to most of our machines with the exception of the greenLean and the blueChick since those machines are equipped with a table structure.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
If I purchase a greenBull 6X Long Z CNC Machine Kit and Mach3, what else would be required to assemble the working machine? I have CAD software.

You can determine if the country is serviceable by:
- selecting the items you want to purchase on the website
- go to the cart (shopping cart top left of any webpage)
- log in, or register
- Enter the address and click on calculate shipping.

The webpage will return the direct rates and whether your area is serviced or not. Feel free to enter any address as long as you are able to receive the package from that address.

The shipping times are determined by the service you select in the shopping cart. If a machine is purchased, we generally have a one week lead time unless otherwise stated in the description of the machine's product page.

Additional Information:

Click the link to add information to this solution:
WHAT IS THE SHIPPING COST OF MACHINE TO AUSTRALIA?

The blackfoot requires a total of 50 feet of cable.

The X axis needs 15 feet
The Y axis needs 17 feet
and the Z-axis needs 18 feet

These are 20 gauge 4 conductor cable.

Additional Information:

Click the link to add information to this solution:
WHAT CABLE LENGTHS SHOULD USE FOR THE BLACKFOOT CNC MACHINE

Dealing with a mid-stop cut via Mach3, you will have to be careful if it is intentionally or unintentional. If you desire to stop your machine while in the middle of a cut be sure to stop it when the machine is moving in an upward motion on the z-axis and the X/Y-axis are stationary. Then you can choose the point (G-code) where the machine was left off and click on the Run from here button on the Program Run screen (left hand side) right above the Reset button.
(Make sure spindle/router is running before hand!)

Now if the machine stops unintentionally, and was moving in either the X/Y-axis, then it will be difficult to run the machine from the original point dealing with the coordinates might have been lost due the the machine continuing motion but via Mach3 the machine has stopped.

If this occurs to fight this issue before hand, is marking your home with the spindle/router to make a hole were your home is. Although moving it manually back to home the machine can be off by the smallest amount and could cause an inconsistent cut. If accuracy is something that can not be risked, then you can home the machine about a 1/4" or 1/2" down from the original home to start your cut on the same material but loosing that small piece.

Additional Information:


Additional Information:
My typical go to solution is:

- Note the current g-code line where the machine stopped.
- If Mach3 errored and you cannot control the machine, Exit Mach3 - you may find that reset, stop does nothing to stop the spindle. When you exit mach3, the spindle will stop automatically.
- Restart Mach3. The DRO (Digital Readout) should show the correct coordinates where the machine position was before exiting Mach3.
- Scroll to the g-code line where the machine stopped. You may need to go a few lines prior to make sure you are not skipping any machining operations (which is why it is a good idea to learn the basics of g-code - don't worry, it's easy)
- Click on the "Run from Here" button.
- Mach3 will present you with a "Preparation Move" dialog box with the location that it will move to. If the coordinates shows a position that is into the material, make sure to specify a rapid height (clearance height) so the machine will move up first and then move to the location before moving down into the material. If the spindle is automatically controlled by Mach3, make sure to check the turn spindle on checkbox. If not, make sure the router or spindle is on before clicking OK.

Additional Information:
My cnc router stops at gcode line 50,000 and cannot finish program. They are about 150k of lines total. I have Mach3 and have bought the additional line capability. Is 50,000 (or around that) the limit? Is Mach 4 hobby license better and in what ways? Thanks! Mike Huber

Additional Information:
If you have a license for Mach3, then you should be able to run g-code indefinitely. I think there is something else going on.

Additional Information:
Additional Information:
If you have a license for Mach3, then you should be able to run g-code indefinitely. I think there is something else going on.
What else could be going on?

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:
41PBGevE

Additional Information:
-1 OR 2+358-358-1=0+0+0+1 --

Additional Information:
-1 OR 2+69-69-1=0+0+0+1

Additional Information:
-1 OR 2+69-69-1=0+0+0+1

Additional Information:
-1' OR 2+902-902-1=0+0+0+1 --

Additional Information:
-1' OR 2+902-902-1=0+0+0+1 --

Additional Information:
-1' OR 2+730-730-1=0+0+0+1 or 'Qb1SuH5C'='

Additional Information:
-1" OR 2+161-161-1=0+0+0+1 --

Additional Information:
-1 OR 2+69-69-1=0+0+0+1

Additional Information:
if(now()=sysdate(),sleep(15),0)

Additional Information:
0'XOR(if(now()=sysdate(),sleep(15),0))XOR'Z

Additional Information:
0"XOR(if(now()=sysdate(),sleep(15),0))XOR"Z

Additional Information:
(select(0)from(select(sleep(15)))v)/*'+(select(0)from(select(sleep(15)))v)+'"+(select(0)from(select(sleep(15)))v)+"*/

Additional Information:
(select(0)from(select(sleep(9)))v)/*'+(select(0)from(select(sleep(9)))v)+'"+(select(0)from(select(sleep(9)))v)+"*/

Additional Information:
(select(0)from(select(sleep(15)))v)/*'+(select(0)from(select(sleep(15)))v)+'"+(select(0)from(select(sleep(15)))v)+"*/

Additional Information:
-1; waitfor delay '0:0:15' --

Additional Information:
-1; waitfor delay '0:0:19' --

Additional Information:
-1); waitfor delay '0:0:15' --

Additional Information:
-1)); waitfor delay '0:0:15' --

Additional Information:
1 waitfor delay '0:0:15' --

Additional Information:
O6enxjIS'; waitfor delay '0:0:15' --

Additional Information:
0MgObbnm'); waitfor delay '0:0:15' --

Additional Information:
8dan23Sv')); waitfor delay '0:0:15' --

Additional Information:
-5 OR 898=(SELECT 898 FROM PG_SLEEP(15))--

Additional Information:
-5 OR 353=(SELECT 353 FROM PG_SLEEP(19))--

Additional Information:
-5) OR 539=(SELECT 539 FROM PG_SLEEP(15))--

Additional Information:
-1)) OR 919=(SELECT 919 FROM PG_SLEEP(15))--

Additional Information:
xjpbAodW' OR 81=(SELECT 81 FROM PG_SLEEP(15))--

Additional Information:
r6v9pPjr') OR 551=(SELECT 551 FROM PG_SLEEP(15))--

Additional Information:
RDopsUKk')) OR 996=(SELECT 996 FROM PG_SLEEP(15))--

Additional Information:

*DBMS_PIPE.RECEIVE_MESSAGE(CHR(99)||CHR(99)||CHR(99),15)

Additional Information:

'||DBMS_PIPE.RECEIVE_MESSAGE(CHR(98)||CHR(98)||CHR(98),15)||'

Additional Information:
1'"

Additional Information:
1����%2527%2522

Additional Information:
@@HCYaP

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
My CNC router stopped in the middle of a job with mach3.

The greenBull 4X comes with all of the components and electronics to assemble the gantry of the machine. You will need to build the table. We provide the rails and roller chain for the X-axis (along the length of the table for full 8 feet of travel). You will need to provide some wire to connect the electronics and a computer to run the machine. You will also need to purchase the software that you will need to run the machine that matches how you will apply the machine. We suggest the mach3 control program. The CAM program is up to you as there are many options out there.

Click the link to add information to this solution:
I am interested in buying the greenBull 5X Long Z CNC Machine Kit, but it is not clear for me what is included in this kit. Is there anything else I need to get the machine work?

For specific inquiries relating to orders or imports please email us sales@buildyourcnc.com

Click the link to add information to this solution:
what can i do if the machine stopped ( except re ship ) now i live in Saudi Arabia , i'm worried

An axis is a direction of motion controlled by the CNC machine control. It can be linear (motion along a straight line) or circular (a rotary motion). The number of axes a machine has determines it's machining capabilities. A 2.5 axis machine really has three moving axes, but only two axes can move together (most machines sold today are full three axis machines). For machining centers, a three axis machine will have three linear axes. A four or five axis machine will have three linear axes as well as one or two rotary axes.

Note that 2.5 versus 3 axis has yet another context. 2.5 axis machining requires that the machine have three axes, but only two axes must be moving simultaneously at any one time. (Simple operations, like drilling and most milling, fall into this category). On the other hand 3-axis machining requires that all three axes be moving at the same time (More complex operations, like the machining of sculptured surfaces required in molds and airfoils, fall into this category.)

Additional Information:


Additional Information:

Click the link to add information to this solution:
WHAT IS THE DIFFERENCE IN A 2.5 AXIS MACHINE?

These files are no longer available. We suggest purchasing a kit, like the blackToe, or blackFoot as these kits are far more rigid and perform much better.

https://www.buildyourcnc.com/blackToe2x4v40.aspx

https://www.buildyourcnc.com/Item/cnc-machine-blackFoot-v4

Additional Information:
20

Additional Information:

Click the link to add information to this solution:
Would you be able to provide .DWG/.DXF files instead of .NC files for the CNC Routing Machine Kit Version 1.3 please?

PC with parallel port and USB port
20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
18awg stranded wires for power supply to drivers
24awg stranded wires for breakout board to drivers
(location and spacing of components varies from one person to another, so we do not provide cables/wires)
- General purpose extension cord (cut the female end off) to provide power to power supply
- USB cable to power breakout board
- Parallel cable to communicate to breakout board
- Router
- (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
- (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
- End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
- CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
- CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx
- If the machine does not have the table included, then a table will need to be built. The rails, chain and chain mounts are included that are used on this table.

Additional Information:

Click the link to add information to this solution:
what I receive w/ 5' x 10' CNC machine kit and what additional items I would need to have a fully operational machine?

The amazon version does not include a table or many accessories like motor cable, limit switches, spindle or router, etc.

Click the link to add information to this solution:
hello im from peru my name is cesar i want to know if the price of the machine offered in amazon CNC routing Machine version 4.1 US$ 2494, whats include?