The leadscrew length for the greenBull long Z-axis is 47 inches.

Additional Information:

Click the link to add information to this solution:
BUILDING ONE OF YOUR GREENBULL 6X LONG AND 2.2 KILOWATT SPINDLE DOES NOT FIT. SEEMS LEAD SCREW YOU SENT WITH KIT IS SHORT 42" LOOKS LIKE IT NEEDS TO BE 5 OR 6 INCH LONGER. THIS CORRECT? WHAT THE NEEDED LENGTH FOR UNIT?

Can you provide the model number of your VFD?

Yes, I have the "YL600 - 2S - 2K20"

It just came with a small booklet that is all in Chinese...

Click the link to add information to this solution:
I WIRED MY VFD (2.2KW VERSION) AND TRIED TEST RUNNING THE SPINDLE. CONFIGURED TO YOUR SPECS ON THIS WEBSITE, ONLY ISSUE IS WE GOT AN ERROR CODE. ERR 02, DO YOU KNOW WHAT IS? OR HAVE A LIST OF CODES? THANK

VFD settings........
1) To program the VFD, wire it up, plug it in. It takes several seconds to come to life.

2) Push the PRGM button to enter programing mode.

3 )Push the SET button. The display will read PD000.

4) If you push the SET button again, it will display the present setting of PD000.

5 )By pushing the up or down arrows, you can change the setting to whatever it needs to be. (This is just an example. PD000 needs no changes)

6)Push the SET button again to lock in the setting of PD000 and advance to the next number, in this case, PD001.

7) Push the SET button and it will display the present setting of PD001. Again, use the up and down arrows as necessary to set PD001, then push SET again to lock it in.

Note: You can also scroll through the PD numbers with the up and down arrows.

8) make all settings this way.

9) by pushing the SET button you can scroll through the settings. First push of SET moves to the next number, second push displays it's setting, third push moves to the next PD number.

Note- If you take too long, it will leave the programing mode on it's own. If it does, just push PRGM again to return to programing mode. Then press SET and continue what you were doing.

10) Start with PD013. Set it to 1, which returns the settings to the factory settings.

11) Then set PD005 to 400, PD004 to 400, and PD003 to 400 IN THAT ORDER.

12) Then set the following: PD041=8, PD144=3000

13) Set PD209=50

That's it for the programing. You should get 24000RPM when you push RUN.

Click the link to add information to this solution:
I JUST RECEIVED A REPLACEMENT SPINDLE (2.2KW 220V). HOWEVER, WHEN ATTEMPTED IT USE THE NEW SPINDLE, WOULD ONLY REACH 1500 RPM. IS THERE SOMETHING NEED TO CHANGE ON CONTROLLER?

Yes, we were waiting for the VFDs and Spindles to arrive from China. We emailed you the tracking numbers today.

Click the link to add information to this solution:
I ordered a 1.5kW 110V Spindle on 11/28. It still shows "processing." Is this on backorder? Any ETA I can expect?

BYCNC response:

Milling aluminum is no problem with our machines.

Here is a video we recently did with our 4'x8' machine. The aluminum piece is about 1/4" thick: https://buildyourcnc.com/tutorials/tutorial-greenbull-aluminum-cutting

The accuracy you will see from our our 2.2kW spindle is entirely dependent on the precision of your build, so it's not possible to say what level of accuracy you can achieve without an examination of the complete system. However, our spindles have a runout of less than .0001 in, which includes the collets that we sell. If you use a collet from another manufacturer, we cannot guarantee this TIR (Total Indicated Runout) dimension.

For the dimension drawing of the anti-backlash nut, please contact us directly by phone or email to techsupport@buildyourcnc.com

User response:
I have emailed waiting for your reply.

User response:
Hi, I am still waiting for your email reply.

BYCNC response:
Your email has been sent.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
HI, I HAVE INTENTION OF PURCHASING YOUR 1/2 INCH PRECISION LEAD SCREW SET TO BUILD MY CNC MACHINE, COULD THE SCHEMATIC DIMENSION ANTI-BACKLASH NUT, BEARING FOR AND SHIM? ALSO IS 2.2KW SPINDLE ABLE MILL ALUMINUM WHAT ACCURACY?

BYCNC response:

Milling aluminum is no problem with our machines.

Here is a video we recently did with our 4'x8' machine. The aluminum piece is about 1/4" thick: https://buildyourcnc.com/tutorials/tutorial-greenbull-aluminum-cutting

The accuracy you will see from our our 2.2kW spindle is entirely dependent on the precision of your build, so it's not possible to say what level of accuracy you can achieve without an examination of the complete system. However, our spindles have a runout of less than .0001 in, which includes the collets that we sell. If you use a collet from another manufacturer, we cannot guarantee this TIR (Total Indicated Runout) dimension.

For the dimension drawing of the anti-backlash nut, please contact us directly by phone or email to techsupport@buildyourcnc.com

User response:
I have emailed waiting for your reply.

User response:
Hi, I am still waiting for your email reply.

BYCNC response:
Your email has been sent.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
HI, I HAVE INTENTION OF PURCHASING YOUR 1/2 INCH PRECISION LEAD SCREW SET TO BUILD MY CNC MACHINE, COULD THE SCHEMATIC DIMENSION ANTI-BACKLASH NUT, BEARING FOR AND SHIM? ALSO IS 2.2KW SPINDLE ABLE MILL ALUMINUM WHAT ACCURACY?

That will depend on the controller that was installed in the redFly. If the controller is a pokeys57CNC controller, you can use Mach 4 with that system.

You can add a 4th axis and an ATC (Automatic Tool Changer) with the redFly system.

Click the link to add information to this solution:
Does the Redfly that I bought with the GreenBull in 2016 work with Mach4? Also I want to add a 4th axis and a spindle with automatic tool changer. Will this work too or do I need a new control board? I bought my CNC with a longer Z travel, so I have plenty of room for these. Thanks!

Yes, you can find all of the instructions for the blackToe CNC Router here:
https://buildyourcnc.com/item/cnc-machine-blacktoe-v4-2x4

Click the link to add information to this solution:
I recently purchase the BlackToe v2.1 (4x8) at a local school auction. The table is complete, however, it is missing the spindle and came in 4 (four) separate pieces. Are there plans for this machine that I would be able to use to reconstruct and determine if anything else is missing.

Buying both the blackToe and the 4th axis is an available option, but take into account the clearance available on the gantry. The best option for the table will be a adjustable mid-section table. That will be able to lower when the 4th axis is going to be used. Or have a elongated table that has a portion for the basic CNC, then a section for the 4th axis.

Click the link to add information to this solution:
Would it be possible to buy the blackToe, and the 4th Axis, then build your own Tslot table to attach both items to? Would a setup like this be possible?

http://buildyourcnc.com/PrimeronHomingandLimitSwitches.aspx
There is a pin setting in Mach3 that says how to react to the inputs from the switches. Your setting is probably wrong as the trigger happens immediately.

You may want to think about shielded wire and/or a resistor on each limit switch line. If there are stray wires, connect them to ground. Additionally, the shield from the shielded cable insulation should alse connected to ground at both ends.
Try upping the Debounce interval in Mach3. You have to adjust the debounce interval. You go to config,general config, and it is in the top right corner. I set mine to 100 and it seems to work well.

Additional Information:
how to solution cnc revo 540 limit tripped error?


Additional Information:


Additional Information:


Additional Information:

Click the link to add information to this solution:
THE SWITCHES KEEP TRIPPING! AT TIMES IT IS LITERALLY AS SOON CLICK RESET ON MACH 3 THEY TRIP AGAIN.

All of our CNC machines can cut melamine. If your application (kitchen doors) requires large cutting area, then I would recommend the following machines:

- greenBull 4x (4'x8'), 5x (5'x10') or 6x (6'x 12')

- greenLean 4'x8' vertically oriented CNC machine

- Or our Fabricator Pro 4'x8' metal CNC machine

Click the link to add information to this solution:
CAN YOU RECOMMEND WHICH CNC MACHINE TO GO WITH FOR CUTTING MELAMINE AND MAKING KITCHEN DOORS FROM MDF. ALSO DO PROVIDE TRAINING ON OPERATING SETTING UP SHOP PRODUCTION USE? THANKS

Yes, it is feasible to create a machine with a cutting area of 13'x15'. Your mechanical and structural systems will need to be able to span a bit more than the 13' if that will be the axis travel along the gantry.

We have not cut carpet with our lasers, but I don't see why not. With that said, be extremely careful with the materials in the rug. Read the MSDS (Material Safety Data Sheet) for the rug you intend to cut as some materials will emit corrosive and harmful gases and chemicals when lased.

Click the link to add information to this solution:
Hi I want to build a cnc laser table 13'x15' cuttting area. Is this feasible. Also would the 80watt laser be enough power to cut through carpet

We have not had any issues with stock firmware on the AWC708lite. Upgrading the firmware will be at your own risk. We can contact our supplier and see if they can provide a suggestion for updating firmware. Contact customerservice@buildyourcnc.com to inquire with a person who can help.

Additional Information:
Working area setting

Additional Information:
Working area setting

Click the link to add information to this solution:
what is the recommended firmware for the awc708c laser controller? I see this download on the Sinjoe site: AWC708 Lite Update Firmware 160901L1

Are you using a laser controller?

Additional Information:
Had this same issue with a thunder laser. It turned out to be a simple check box setting in the software. I can't remember exactly, but I think it's was the mhz.

Click the link to add information to this solution:
My laser fires when traveling to its origin positon after finishing the job. Also once turned on , it will fire all the way to where it was before it was turned off.

At this time we are working to release a new USB controller board that will be compatible with Mach4 software and do not have any immediate plans to update the Planet-CNC USB board.

Click the link to add information to this solution:
Are there plans to release a USB Controller to work with the Planet CNC Output Board for more advanced spindle control from within Planet CNC?

Our 1.5/2.2kW spindle will work with both setups, in our wiring diagram it is more seen as the Euro/AUS-style, however you can do the same thing with the North American style as well. Also depending on if you have single or three phase 220V, you can use pins R, S, T. A manual will arrive in the VFD box, which will have further information and diagrams.

Please seek a certified electrician if you are unsure of any aspect in wiring the spindle or VFD, since wiring to main lines will require wiring of the plug and main lines to the inverter and to avoid any damage or injury's while installing the 1.5/2.2kW spindle and VFD combo.

Click the link to add information to this solution:
Does the 2.2kW 220V Spindle need Euro/AUS-style 240V power (1 hot, 1 neutral, 1 ground) or do North American 220V style welding plugs (2 hots, 1 ground) also work? Thx!

Yes, that is the cable we use for all of our 4-wire motors in motion applications.

The cable is specially made for motion applications and has a 20 AWG conduit size.

Click the link to add information to this solution:
Is this the correct (4 wire ) for motor wire extension on 5x? https://buildyourcnc.com/item/electronicsAndMotors-cable-wire-20awg-wrcon

Depending if the spindle can work with this specific VFD, it might be possible. However we would not like to risk you working unit, with a possible match so we would like more details on your specific model and any information available on the spindle itself.

Response
The only info on the spindle is 2.2KW 400HZ 220V. Made by Zhong Hua Jiang.

Was originally on a Delta C200 vfd. That is 220 single phase.

Click the link to add information to this solution:
I PURCHASED A VFD AND SPINDLE FROM FRIEND, HIS SET UP IS 220. DON'T HAVE 220 IN MY SHOP. QUESTION CAN USE YOUR 110 WITH THIS SPINDLE??

I just looked at your account and noticed that your shipments has not been made yet. I will talk to the shipper tomorrow morning when the office opens determine what happened. My apologies for this.

Click the link to add information to this solution:
I ordered a 1.5kW Spindle and Inverter (110 Volt) on December 18th and have heard nothing since. I notice you did charge my credit card for the purchase. Please update me with an ETA as soon as possible.