VFD settings........
1) To program the VFD, wire it up, plug it in. It takes several seconds to come to life.

2) Push the PRGM button to enter programing mode.

3 )Push the SET button. The display will read PD000.

4) If you push the SET button again, it will display the present setting of PD000.

5 )By pushing the up or down arrows, you can change the setting to whatever it needs to be. (This is just an example. PD000 needs no changes)

6)Push the SET button again to lock in the setting of PD000 and advance to the next number, in this case, PD001.

7) Push the SET button and it will display the present setting of PD001. Again, use the up and down arrows as necessary to set PD001, then push SET again to lock it in.

Note: You can also scroll through the PD numbers with the up and down arrows.

8) make all settings this way.

9) by pushing the SET button you can scroll through the settings. First push of SET moves to the next number, second push displays it's setting, third push moves to the next PD number.

Note- If you take too long, it will leave the programing mode on it's own. If it does, just push PRGM again to return to programing mode. Then press SET and continue what you were doing.

10) Start with PD013. Set it to 1, which returns the settings to the factory settings.

11) Then set PD005 to 400, PD004 to 400, and PD003 to 400 IN THAT ORDER.

12) Then set the following: PD041=8, PD144=3000

13) Set PD209=50

That's it for the programing. You should get 24000RPM when you push RUN.

Click the link to add information to this solution:
I just received a replacement spindle (2.2kW 220v). However, when I attempted it use the new spindle, it would only reach 1500 rpm. Is there something I need to change on the spindle controller?

Planet CNC has the option to turn off these outputs on your USB board. Under the File/settings/Pins. You will have Spindle (M3,M4,M5) Coolant (M7,M8,M9) as available output pins. On the drop down tabs for these output pins you will have this option ( --- ), if selected it will turn of that output pin in your board and you will get not voltage change in the pin.

Additional Information:
Cannot activate output in mkx

Click the link to add information to this solution:
On the USB controller I am unable to get voltage from the Mist relay block on the board. The Flood and Spindle produce a voltage change correctly. Is there a setting I am missing?

Do you have the Pokeys57CNC connected to a 24V external power supply?

Additional Information:
Yes, a 24V external power supply with the jumper positioned. I'm using the ethernet port so the 24v is the only source of power. I plan to measure the amp draw when I have a chance to see how much the vfd is drawing on the analog out.

Additional Information:
Further information. The resistance across the terminals on the vfd is 22k ohms. With an independent 0-10v current source I can run the spindle from 20 to 400 Hz. The PokeysCNC only gets to 3.8v with the vfd attached (and the vfd is at 150 Hz) compared to 10v when the vfd is not attached. The power to the PokeysCNC is steady at 24.18 V, so I'm not maxing out the power supply. Still looking for thoughts on what might be going on?

Additional Information:
And the other thing - The measured amperage is 0.17 mA for the 0-10 V signal (which makes perfect sense for 3.7 V and 22k Ohms).

Additional Information:
Just to bring finality to this issue - I added a 2.2 microfarad capacitor across the 0-10V input terminal (from signal to ground). This solved the issue. Evidently, it was an electrical noise issue.

Click the link to add information to this solution:
My pokeysCNC board creates and analog signal of 0-10V for 0 to 24000 spindle rpm just like it should from Mach3. However, when the spindle is on, the voltage only gets to about 3.8V for 24000 rpm. It seems like the vfd is drawing more current than the pokeyscnc analog output can produce. It there an easy solution to this problem?

Yes, you can find all of the instructions for the blackToe CNC Router here:
https://buildyourcnc.com/item/cnc-machine-blacktoe-v4-2x4

Click the link to add information to this solution:
I recently purchase the BlackToe v2.1 (4x8) at a local school auction. The table is complete, however, it is missing the spindle and came in 4 (four) separate pieces. Are there plans for this machine that I would be able to use to reconstruct and determine if anything else is missing.

You can control our 40W laser power supply (which controls the laser tube) with an Arduino, if that is your intention. The trigger for turning the laser on and off uses a 5V level. To control intensity, you can use the Arduino PWM output. If you want the Arduino to move the machine as well (providing pulse trains to each of the stepper motor drivers) then you will need to make sure you consider the processing speed of the Arduino so you will be able to run the stepper motors at the speed you need for the laser engraving/cutting.

Our laser controller do all of these functions. Here is a link to our laser control system:
https://www.buildyourcnc.com/item/Laser-Component-Laser-Control-System



Additional Information:
Thank you! I am building a 3 axis cnc/ engraver and I think this would be a good option as well as the router head and the 3d printing head. How heavy is the tube? I may mount it directly onto one of the axis of the machine to eliminate the need to line up all three axis, similar to what you have with your xl engraver.

Additional Information:
The tube isn't that heavy, but when filled with water, it can get up to a few pounds. The key is to use the axis moving the nozzle for engraving as this requires fast back and forth motion. The cutting is generally dependent on the axes moving from vector to vector at a relatively slow motion, so this is not a problem.

Click the link to add information to this solution:
I would like to build a low cost laser engraver/ cutter, can your 40w laser power supply be controlled with an arduino or is it only controlled by the controller sold here?

If the Z-Axis is moving down when you press the page up or page down (or by moving the z-axis by another means like with an MPG, Pendant, or the built-in MPG in Mach3), then the direction signal wire is not connected correctly. The direction signal wire works by moving in one direction with a low signal (like gnd) and moving in the other direction with a high signal (like 5v). If the signal stays at one of the two signals, it will only move in the direction of the current signal state. Recommended action is to determine if the DIR- and DIR+ signal wires are connected securely and make good contact at the driver and controller sides.

Click the link to add information to this solution:
I installed a pokeys57cnc and use Mach3 for the mill. When I page up or down the Z axis moves down. Is there a setting I need to change? I checked the Z axis wiring and it matches the X and Y axis which function correctly.

If the Z-Axis is moving down when you press the page up or page down (or by moving the z-axis by another means like with an MPG, Pendant, or the built-in MPG in Mach3), then the direction signal wire is not connected correctly. The direction signal wire works by moving in one direction with a low signal (like gnd) and moving in the other direction with a high signal (like 5v). If the signal stays at one of the two signals, it will only move in the direction of the current signal state. Recommended action is to determine if the DIR- and DIR+ signal wires are connected securely and make good contact at the driver and controller sides.

Click the link to add information to this solution:
I installed a pokeys57cnc and use Mach3 for the mill. When I page up or down the Z axis moves down. Is there a setting I need to change? I checked the Z axis wiring and it matches the X and Y axis which function correctly.

To make an axis move in the opposite direction to what it is currently moving, you will need to toggle the ":direction:" active low setting for that axis. for instance, if when you press the page up button and your z-axis move down instead of up, then you need to make this change in the configuration.

To do this in Mach3:
- Click on the config option in the top menu
- Click on ports & pins
- Click on the motor outputs tab
- on the axis you wish to reverse, click on the "dir active low" to toggle the state of that parameter.

Click the link to add information to this solution:
I installed a pokeys57cnc and use Mach3 for the mill. When I page up or down the Z axis moves down. Is there a setting I need to change? I checked the Z axis wiring and it matches the X and Y axis which function correctly.

To control a spindle using the USB CNC interface, you will need a relay board that contains a transistor that can activate the relay with a power source with enough current that can activate the relay. This video explains all of the information you will need to develop this relay circuit:

Click the link to add information to this solution:
i have a breakout usb controller iam using a spindle output to active a relay 5V but it didnt work.... whats the problem, what else i need to active that realy 5v 10A?

No, we have gotten away from the planet-cnc boards as they have decided to not support our board with their software. You can use the Mach3 USB board as an alternative. You will be better off with Mach3 as a control software as this is widely used and supported.

Mach3 USB board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
I have the older discontinued USB breakout board. The y-axis no longer works and have traced it to the breakout board. Is there a replacement board that can use the same Planet CNC software running on Windows 10?

The wire that is connected to the spindle can be a simple extension cord, that you find at a local hardware store. However there is a missing wire that is required(ground) which will have to be the same amperage of the extension cord.

Click the link to add information to this solution:
What wire do I need to power the spindle (ie, from the 220 outlet to the spindle). Would a dryer cable work? Is there specific amperage the wire needs?

Did this spindle come with a 110V 1.5kW VFD?

Additional Information:
The reason I ask is because the 220V 1.5kW spindle may work well with the 110V 1.5kW VFD. I believe we did the test prior to shipment.

Additional Information:
I have a 110V HY01D511B VFD already. I did not know they would work together. I will give this a try.

Additional Information:
If you did't get the VFD paired with the spindle from us, then I would not connect the 220V spindle with your VFD. Let me ask my technician and get back with you.

Additional Information:
My technician said that it should work since the 220V 1.5kW spindle worked with our 1.5kW 110V VFDs.

Remember to seek the advice and guidance of a professional electrician when connecting these types of high powered devices.

Additional Information:
Do you have any info on the settings? I would rather buy a pre-configured VFD from you if you don't have the settings for my HT since I have already fried one spindle because of lack of documentation from the manufacturer. If you can setup a VFD that works with the spindle you sent at 110v input voltage I would be fine with the extra expense.

Click the link to add information to this solution:
I ordered a 1.5KW 110 volt spindle. I just received the box and the spindle clearly says on the foam packaging and the side of the spindle that it is 220V. I think you shipped me the wrong spindle

Did you install the Mach3 USB plug-in?

Make sure that you followed all of the steps and diagrams on the following page:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
ABSOLUTELY NOTHING WORKS. I HAVE ALL STRUCTURE AND MECHICAL PARTS OF THE BLACKTOOTH CUTTER DONE. HOWEVER WHEN WIRE UP STEPPER MOTOR TO DRIVER. THAT MACH 3 USB CONTROLLER BOARD, TRY JOG MOTOR, WORKS! PREVIOSULY HAD PLANET CNC BREAKOUT HOWRVER, ONLY MOVED MOTORS IN ONE DIRECTION COULDNT CHANGE IT. ANY HELP WOULD BE APRECIATED

If you want speed control, it is recommended to use the RS-485 connection on the VFD and use the control program such as Mach3 to communication serially with the VFD using this RS-485 connection.

If you would rather use a controller such as the PMDX-107 to simulate the effect of a potentiometer using the Aref, Aout and Agnd and the Rev/Dir and Fwd/Run terminals to control operation and direction, you can connect those to the VFD.

PMDX-107 Aout connects to the VI (analog voltage in). This is like the wiper on a potentiometer.
PMDX-107 Agnd connects to the ACM terminal on the VFD for Analog common.
PMDX-107 COM connects to DCM terminal on the VFD for Digital common.
PMDX-107 Fwd/Run connects to the FOR terminal on the VFD for Forward.
PMDX-107 Rev/Dir connects to the REV terminal on the VFD for Reverse.

Refer to your PMDX-107 manual to correctly configure your dip switch settings and make sure to calibrate (tweak) the speed control using the trimmer next to the terminals on the PMDX-107.

Click the link to add information to this solution:
I purchased the 4.0kw spindle and VFD a while back, and have just installed a PMDX-107 controller... do you have any examples of the wiring connections for the SL-240EE to PMDX-107?

Yes, you can use a corner plate very easily. You will want to make a corner plate that has three independent plates that do not conduct with each other. Each of these plates will be connected to a different input (i.e. IN1 for X, IN2 for Y and IN3 for Z). The end mill or tool that is inserted into the spindle will connect to V- of the 24V power supply, or the DCM on the controller, which is connected to the 24V V-. Then, you can use the ref all home button on the program run screen of Mach3.

Click the link to add information to this solution:
Is there a way to use an X,Y plate that will only be responsible for corner finding in Mach3 with the Mach3 USB controller?

At this time we are working to release a new USB controller board that will be compatible with Mach4 software and do not have any immediate plans to update the Planet-CNC USB board.

Click the link to add information to this solution:
Are there plans to release a USB Controller to work with the Planet CNC Output Board for more advanced spindle control from within Planet CNC?

Sure, not a problem at all. You will need to call our office and provide your information so that we can change the correct order.

Our phone number can be seen by hovering over the "Need Help?" at the top right of each page.

Click the link to add information to this solution:
hi, would like to make a change on my order, i purchase this part 2.2kW Spindle with 220V Inverter $528.00, and would like to make it for 110 volts instead of 220v. please

The 2.2kW spindle will have the same amount of torque and strength using either the 110V or the 220V inverter. Nothing will significantly change in either application since the 110V inverter has a small step up transformer which will increase the voltage from 110V to 220V to run the spindle efficiently.

Additional Information:
I'd like confirmation on this -- isn't there a cost in efficiency to having the 110v step up to 220v?

Additional Information:
Thank you so very much for explaining this!!! I truly appreciate your help! Tricia

Additional Information:
Thank you so very much for explaining this!!! I truly appreciate your help! Tricia

Additional Information:
Thank you so very much for explaining this!!! I truly appreciate your help! Tricia

Additional Information:
Thank you so very much for explaining this!!! I truly appreciate your help! Tricia

Additional Information:
Thank you so very much for explaining this!!! I truly appreciate your help! Tricia

Click the link to add information to this solution:
Good morning, I would like to know if the strength of the 2.2kw spindle is weaker when using the 110V version of the VFD. Does it have the same power as the 220V version VFD?

We could not guarantee, nor say, whether or not your current software would be able to utilize the USB breakout board. Our USB breakout board is designed for use with Planet CNC software found here, http://www.planet-cnc.com/index.php?page=software

As far as we know, this is the only CNC Controller software that operates on a USB breakout controller.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I want to change my old DSP controller and break out board with new one in your site that support usb it is possible ? if yes can we contact us to talking about details ?