The Mach3 USB controller will work with M3/M4/M5 or M7/M8/M9 combinations. M10/M11 is not available with the controller.

Click the link to add information to this solution:
[575] does the mach3 usb interface board support the M11/M10 command set?

In our experience, the backlash compensation is not an ideal mechanism to solve backlash issues. It is best to resolve the backlash issue mechanically regather than through software.

Boards that handle all instructions on its own chip (which is the case for this all other USB boards) take some control away from Mach3. Without Mach3 having granular control. With that said, we do not have experience with the backlash compensation with that particular board. Our experience with backlash compensation with other boards have resulted in very poor accuracy and undesirable geometrical moves.

Additional Information:
zokkj

Additional Information:
zokkj

Additional Information:
zokkj

Additional Information:

Click the link to add information to this solution:
Mach3 USB Interface Board, Backlash Compensation in Mach3 is not working. Does this board support the backlash function?

If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

Additional Information:
ur gay

Additional Information:

Click the link to add information to this solution:
MY COMPUTER DOES NOT HAVE A PARALLEL PORT. HOW DO I INTERFACE WITH THE BREAKOUT BOARD?

Yes, the Mach3 USB controller will work with the latest Windows version and in 64-bit mode. The 32-bit mode is only relevant for using the parallel port driver if you are using a parallel port breakout board. Since this controller is connected via a USB cable, the 64-bit state will work fine.

Additional Information:
mach3 not showing in device manager

Click the link to add information to this solution:
[575] I have a 64 bit Windows 11 laptop. Will this interface board work with this? If not is there an option you can suggest.

The Mach3 USB controller is specifically engineered to integrate seamlessly with Mach3's CNC control software. Easel, on the other hand, offers an all-in-one CAD/CAM solution along with machine control capabilities. While Easel can output standard G-code compatible with industry-standard post-processors, it can serve as a design tool when used in conjunction with Mach3 but not as the machine control software.

Click the link to add information to this solution:
[575] Will the Mach3 USB interface board support other software such as Easel?

The pulse stream is output directly from the onboard microcontroller on the Mach3 USB controller, so there is no need for a safety charge pump from the computer to the controller. Parallel port breakout boards were connected to the computer via GPIO pins (General Purpose Input/Output) and each pin dedicated to the step pulse would be output directly from those pins. In that case, a safety charge pump was needed.

Additional Information:
20

Additional Information:
20

Click the link to add information to this solution:
[575] The older B.O.B. needed a charge pump as an added safety feature, does this U.S.B. board need a charge pump?

Our MAch3 USB interface boards can be located here:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
I AM INTERESTED IN THE 3 AXIS COMBO USB OPTION. NOTICE YOU ENDORSE PLANET-CNC FOR USE WITH THIS BUT WILL MACH3 INTERFACE WELL BEAK OUT BOARD?

If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

Additional Information:
ur gay

Additional Information:

Click the link to add information to this solution:
MY COMPUTER DOES NOT HAVE A PARALLEL PORT. HOW DO I INTERFACE WITH THE MACHINE?

Yes, you can use a conductive metal to serve as a zeroing block for the Z axis. All you need to do is connect the block (conductive metal) to one of the 4 inputs on the controller. The end mill must be connected to the DCM terminal (the GND of the 24V power supply) of the controller. In the inputs dialog box (config-ports and pins-inputs). Under the probe line, enter port 3 and the pin used for the block.

Click the link to add information to this solution:
[575] Hi can I use a zeroing block with mock three interface board and do you have one I can purchase and directions on how to set up

Yes, you can use a laptop if you have a controller that uses a USB, like the Mach3 USB card. If you don't have that, you can purchase that part here:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

If you have a controller board that connects to a 25 pin connector, modern laptops will not be able to connect to that port.

How old is your CNC computer system?

Additional Information:
The CNC computer system is 2013 (5 years). The built in video card went out. I will order the Mach3 USB card. Thank you.

Additional Information:
You're welcome

Click the link to add information to this solution:
The motherboard on the computer I bought from you went out. What would you suggest. I have a laptop, could I use it and use a Mach3 USB interface board?

Our MAch3 USB interface boards can be located here:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
I am interested in the 3 axis combo USB option. I notice you endorse the Planet-CNC for use with this but will Mach3 interface well with the USB beak out Board?

Connect the XD to the Dir, XP to the Step, and the 5V on the Mach3 USB controller to the +5V.

Click the link to add information to this solution:
[575] I have motor control boards that have 4 pin input ( Step, Dir, EN, +5V) how do I connect this USB board?

You can connect the 5V from the Mach3 USB controller to the 5V terminal on the driver, the XP to the Step terminal on the driver and the XD to the Dir terminal on the driver.

Click the link to add information to this solution:
[575] I have motor control boards that have 4 pin input ( Step, Dir, EN, +5V) how do I connect this USB board?

I would recommend using a separate 24VDC power supply for the controller. The 24VDC that is connected to the controller is used for delicate input signals and output signals that control external devices. To keep interference and possible current and voltage fluctuations at a minimum due to the motor load, a separate power supply would be best.

Click the link to add information to this solution:
[575] Can the 24VDC supply used for the interface board be the same supply used for stepper drivers, or do you need separate power supplies? If not, does GND and DCM need to be isolated?

The dimensions for our USB breakout board are:

L: 2.745"/ 69.723mm
W: 2.244"/ 56.9976mm
H: .501"/ 12.7254mm

Currently we do not have a CAD model on hand.

Click the link to add information to this solution:
What are the overall dimensions of the USB interface board? Is there a CAD model available?

You can add a limit switch to either the USB or the parallel board. Please refer to the product pages for these items to view wiring diagrams.

Click the link to add information to this solution:
I want to add limit switches but I have no connections on the breakout board. Can I use a usb interface board for the limit switches as well as the parallel port for the running?

You can add a limit switch to either the USB or the parallel board. Please refer to the product pages for these items to view wiring diagrams.

Click the link to add information to this solution:
I want to add limit switches but I have no connections on the breakout board. Can I use a usb interface board for the limit switches as well as the parallel port for the running?

The Mach3 USB board will fit in the redLeaf, but you may need to modify the Plexiglas top for proper mounting. However, the redLeaf has the proper parallel GPIO on the motherboard for use with the Parallel breakout board. If you have a laser on the machine you are using, then I would urge you to maintain the parallel breakout board as the Mach3 USB board will not work correctly using the Z-direction pin and you will need to determine how to use the output pins onthe USB board to ensure proper laser functionality.

Click the link to add information to this solution:
Will Mach3 USB Interface board fit in my redleaf, in lieu of the breakout board that came with it?

The electronics combo with the sku of 101 on Amazon.com includes a parallel interface.

Click the link to add information to this solution:
I am looking at your 3 axis CNC machine kit(part #101) on Amazon. Is the interface on this kit USB?