I do not recommend using the Mach3 USB controller to be used with a torch height controller. There are only 4 inputs on the Mach3 USB controller. We have tried to interface a Proma THC to this board without success; however, we did not exhaust all possibilities.

I would recommend the Pokeys57CNC controller to connect the Proma THC as I have interfaced these two before and they work well together.
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
[575] Hello. Does this USB interface board thc? I have the proma 150.

We generally use the USB to power the interface (breakout board). The current from the computer is sufficient to supply the breakout board.

Click the link to add information to this solution:
Breakout Board with Relay. What is the USB connection on this board for? Does this board Still require a 5v power supply?

The pulse stream is output directly from the onboard microcontroller on the Mach3 USB controller, so there is no need for a safety charge pump from the computer to the controller. Parallel port breakout boards were connected to the computer via GPIO pins (General Purpose Input/Output) and each pin dedicated to the step pulse would be output directly from those pins. In that case, a safety charge pump was needed.

Additional Information:
20

Additional Information:
20

Click the link to add information to this solution:
[575] Can it control a safety charge pump ?

The breakout board receives 5v power from the USB. There is no need for an external 5v power adapter.

Additional Information:
4t5y

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
The breakout board receives 5v power from the USB port and from my computer's USB or does it need to come from a 5v adapter?

The Mach3 USB controller will work with M3/M4/M5 or M7/M8/M9 combinations. M10/M11 is not available with the controller.

Click the link to add information to this solution:
[575] does the mach3 usb interface board support the M11/M10 command set?

You have the ability to designate the 4th axis, commonly known as the A-axis, for rotary indexing operations when using a Mach3 USB controller.

To achieve this in Mach3, you'll need to:

Open the Mach3 software.
Navigate to "Config" and then to "Ports and Pins."
Go to the "Motor Outputs" tab.
Enable the A-axis and assign the respective Step and Direction pins.
Save your settings and exit the "Ports and Pins" dialog.
To calibrate the A-axis, go to "Settings" and use the "Set Steps Per Unit" option.

Click the link to add information to this solution:
[575] Does this board support indexing on mach3 turn? Planning to use it on a lathe and will do threading jobs

In our experience, the backlash compensation is not an ideal mechanism to solve backlash issues. It is best to resolve the backlash issue mechanically regather than through software.

Boards that handle all instructions on its own chip (which is the case for this all other USB boards) take some control away from Mach3. Without Mach3 having granular control. With that said, we do not have experience with the backlash compensation with that particular board. Our experience with backlash compensation with other boards have resulted in very poor accuracy and undesirable geometrical moves.

Additional Information:
zokkj

Additional Information:
zokkj

Additional Information:
zokkj

Additional Information:

Click the link to add information to this solution:
Mach3 USB Interface Board, Backlash Compensation in Mach3 is not working. Does this board support the backlash function?

This controller does not have an encoder input to determine the speed of a lathe spindle. The Pokeys57CNC does have an available encoder input.
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
[575] how do i connect a lathe spindle speed encoder to this usb breakout board controller so i can set up for thread cutting on my lathe and on the mill for threading

The Mach3 USB controller is specifically engineered to integrate seamlessly with Mach3's CNC control software. Easel, on the other hand, offers an all-in-one CAD/CAM solution along with machine control capabilities. While Easel can output standard G-code compatible with industry-standard post-processors, it can serve as a design tool when used in conjunction with Mach3 but not as the machine control software.

Click the link to add information to this solution:
[575] Will the Mach3 USB interface board support other software such as Easel?

You can use this board to have two motors/drivers on a single axis.

You have two solutions for this:

Wire the YP and TD to two drivers so they are receiving the same pulses and direction signals from the controller (if you need the motors to turn in opposite directions, just swap the A and B coils where the motor connects to the driver for one of the drivers/motors). This will free up an axis on the board.

Use the Mach3 slaave axis option where you resolve the two motors on a single axis by software. This will require you to use the extra axis on the board.

Click the link to add information to this solution:
[575] Can this board drive two (2) Y-motors? Design uses 1 X, 2 Y, and 1 Z motor. The schematic has X, Y, Z

Connect the XD to the Dir, XP to the Step, and the 5V on the Mach3 USB controller to the +5V.

Click the link to add information to this solution:
[575] I have motor control boards that have 4 pin input ( Step, Dir, EN, +5V) how do I connect this USB board?

You can connect the 5V from the Mach3 USB controller to the 5V terminal on the driver, the XP to the Step terminal on the driver and the XD to the Dir terminal on the driver.

Click the link to add information to this solution:
[575] I have motor control boards that have 4 pin input ( Step, Dir, EN, +5V) how do I connect this USB board?

This was true for controllers that use the parallel port to communicate with the CNC as the CPU is sending signals to each of the parallel port pins (GPIO or General Purpose Input/Output). With newer types of controllers that use the USB connection, this is not a problem anymore since all of the signal processing happens on the controller rather than in the computer. The computer only needs to send high-level commands to the controller and the controller translates the simple commands to pulse trains that the drivers can accept.

Additional Information:
I don't believe that the board itself buffers. MAch3 however, does use an algorithm for look-ahead.

Additional Information:
Thank you for the information. I plan to use a second SSD with a minimal Windows 10 or 11 system.

Click the link to add information to this solution:
[575] Buffering. In former days, I used a MS DOS application to do the milling jobs. I was told that Windows sometimes does other jobs ans so my milling job would be ruined. Does this USB board buffer some of the CNC data to circumvent such errors?

To use the inputs and outputs on the MAch3 USB controller, you will need at least a 12 VDC power supply inte 24V terminal (V+) and the DCM terminal (V-). The common lead of the limit switch will be connected to DCM (V-) and the NO (Normally Open ) lead of the limit switch will be connected to the Input of your choice (IN1 - IN4).

Click the link to add information to this solution:
[65] So do you need a 24 volt power supply on the USB breakout board or can you use the 5 volt side ?

Are you able to install a newer version of Mach3? If you are worried that your configuration will be lost, you can save the configuration by copying all of the XML files from the Mach folder. The XML files contain all of the settings that you applied in Mach3. Just in case the XML files are not compatible with the new version, make sure not to erase the current Mach3 that you have on the machine.

Click the link to add information to this solution:
[575] Hi, I have an old version of MACH3 V1.84 - Can someone tell me where to place the USB motion drive as there is no plugin folder in this version.

I would recommend using a separate 24VDC power supply for the controller. The 24VDC that is connected to the controller is used for delicate input signals and output signals that control external devices. To keep interference and possible current and voltage fluctuations at a minimum due to the motor load, a separate power supply would be best.

Click the link to add information to this solution:
[575] Can the 24VDC supply used for the interface board be the same supply used for stepper drivers, or do you need separate power supplies? If not, does GND and DCM need to be isolated?

with parallel port controllers, you have the ability to jog using two axes at the same time, but with USB controllers, this is not possible.

Click the link to add information to this solution:
[575] Hi, I recently purchased this board and everything seems to be fine! But I am not being able to jog two axis at same time as I used to do on my older board. Did I do something wrong?

Yes, the Mach3 USB controller will work with the latest Windows version and in 64-bit mode. The 32-bit mode is only relevant for using the parallel port driver if you are using a parallel port breakout board. Since this controller is connected via a USB cable, the 64-bit state will work fine.

Additional Information:
mach3 not showing in device manager

Click the link to add information to this solution:
[575] I have a 64 bit Windows 11 laptop. Will this interface board work with this? If not is there an option you can suggest.

You will need PlanetCNC software for the USB breakout board and when plugging in the USB the computer should automatically recognize the board, however you can go into device manager to see if the USB terminal is working correctly.
The parallel breakout board; the USB is not a connection terminal rather than a power source, and the parallel port will be the communication terminal.
The items you will need for a water cooled spindle would be: water pump, silicon tubing(length desired by customer), a extension cord(from a hardware store(orange))(1 same gauge wire/length as extension cord).

Click the link to add information to this solution:
I have the usb breakout board https://buildyourcnc.com/Item/electronicsAndMotors-electronic-component-USB-Controller-Breakout and need to run the A axis as a slave the software greys out the box how do I fix this?