If one or more motor is not responding, please follow the troubleshooting directions below:

For parallel Bob only! Make sure both the parallel and USB are connected.

Re-check wiring, and connections for continuity (no breaks in the wires) and check for correct wiring locations from driver to BoB.
Check dip switch settings on the driver.
Check components, by swapping the motors (ex. y-axis motor to z or x-axis driver and z or x-axis motor to y-axis driver) to check if motor functions on another driver.
Depending on software check step low active (mach 3) or invert pulse (planet-cnc) for the axis which is not responding.
Mach 3 - config/port & pins/motor outputs / Planet-CNC - file/settings/axes

Click the link to add information to this solution:
I have an engine NEMA 34 from Y axis on my green bull that do not response, I already check connections and everything seems to be OK, how can I check that the motor it's working properly or not?

We may be able to source those motors. Curious, the 6000 oz-in motor is pretty big. Do you mind explaining the application of the CNC machine and the structure that would require the large motor?

Additional Information:
The largest motors we can offer is 3900 oz-in without any mechanical help. 6000 oz-in can be resolved by mechanical means as an alternative.

Click the link to add information to this solution:
I am converting a 12x36 lathe over to CNC, I am interested in a 2 axis kit. I would love one stepper motor to be no smaller than 1200oz. , and another at 6000z. Is this something that you could offer? I have two other cnc machines but this is my first converstion on my own.

Sure, our blueChick and blackToe CNC Routers are considered relatively small machines at 1'x3' and 2'x4' respectively. They both use NEMA 23/24 motors. We recommend connecting the machines to either Mach3 or LinuxCNC and come with the necessary interface for either control software. You will need a computer for the control software and if you desire LinuxCNC, you will need a parallel port. Mach3 will accept either parallel port, or USB interface.

Click the link to add information to this solution:
I recently purchased the linksprite cnc engraving router and was wondering if your 3 axis small kit would be ok? the engraver came with nema 17 motors and a arduino board but but not liking the grbl control. could you point me in the right direction .Thanks.

There are many ways to wire an emergency stop switch. The simplest, and arguably the most certain, way is to wire the switch into the incoming power so that throwing the switch kills all power to every part of the machine. Here is a diagram showing how a customer wired such a switch on their blackTooth laser which you could adapt to your needs. http://www.buildyourtools.com/phpBB3/viewtopic.php?f=12&t=4872

Alternatively, you could use an input pin on your USB board. The wiring would depend on whether and how you might be using limit switches (single or multiple switches; normally open or normally closed). Our website datasheet for the USB board is at https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/ and shows how to configure the switches for each set up. If you use this method, you'd essentially wire the e-stop as a limit switch.

Click the link to add information to this solution:
I recently purchased 3 axis electronics with the USB controller board. I'm trying to install an E-stop switch. Where do I connect that on the controller board?

There are many ways to wire an emergency stop switch. The simplest, and arguably the most certain, way is to wire the switch into the incoming power so that throwing the switch kills all power to every part of the machine. Here is a diagram showing how a customer wired such a switch on their blackTooth laser which you could adapt to your needs. http://www.buildyourtools.com/phpBB3/viewtopic.php?f=12&t=4872

Alternatively, you could use an input pin on your USB board. The wiring would depend on whether and how you might be using limit switches (single or multiple switches; normally open or normally closed). Our website datasheet for the USB board is at https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/ and shows how to configure the switches for each set up. If you use this method, you'd essentially wire the e-stop as a limit switch.

Click the link to add information to this solution:
I recently purchased 3 axis electronics with the USB controller board. I'm trying to install an E-stop switch. Where do I connect that on the controller board?

You have motors and drivers that already work with your machine (unless the drivers are an all-in-one setup and not modular. I would advise you to keep your current electronics and replace the parallel port breakout board with a controller that uses the USB to operate.

Here are two controllers that work under Mach3, or Mach3 or Mach4:
Mach3 USB controller (works under Mach3 only)
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board
Pokeys57CNC full-featured controller works under Mach3 or Mach4:
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Alternatively, you can purchase a complete plug-and-play system or have your control system sent over to Buildyourcnc to modify the control system to use one of the above controllers.

Click the link to add information to this solution:
[422] I have a probotix cnc router purchased in 2014, used to run on linyx, now Mach3, WindowsXP, printer port, i would like to be able to use a modern computer usb, do you have something like a plug & play or control box i can wire this into, 2 Y axis, i lost my auto tool length when i switched to XP also, any help appreciated

You should have no problem connecting the Pokeys57CNC controller to the drivers of your machine as long as the drivers have step (Pulse or PUL) and direction (DIR) terminals. You will need the cable pack that is sold separately so you can connect the headers/connectors of the pokeys57cnc controller to the drivers using ribbon cables.

I show this process in great detail on this page:
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Is you scroll down on the page, you will see a set of videos that show the process step-by-step.

Click the link to add information to this solution:
I have a ShopBot CNC that was converted to Mach 3. The controller has gone out. I pourchased your Pokeys57 board, but I'm not sure I have everything I need. I think my motor drivers are OK, but am not sure how to wire them to what I purchased from you. Need Help. How can we make this work, or do I need a different board to distribute the movement signals to my drivers?

It is normal for stepper motors to get hot to the touch while not moving. There is a setting on the driver that you can set to half current. This is an idle current while the motor is just in a holding position.

Click the link to add information to this solution:
[54] I have two of these motors, both purchased recently as part of the heavy gantry 3-axis combo. They are warm to the touch when not doing anything. Is this normal? They work when jogged w/mach4

can not get the limit switches to work on the usb controller board

Additional Information:
Wiring the motors to the drivers for our 8 wire motor is probably the 425 oz-in NEMA 24 stepping motor. Here is the URL for the diagram of the motor:
https://www.buildyourcnc.com/Documents/PN.SM60HT86-2008BF-U%20(inhouse%20PN.60BYGH303-13)%20(1).pdf

Wire it in bipolar parallel as specified on the data sheet.

Here is the URL for the motor to check if it is the same that you purchased.
https://www.buildyourcnc.com/item/electronicsAndMotors-nema24-425ozin

The USB mach3 board URL is here:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

The wiring diagram is on that page and instruction on how to use it.

Click the link to add information to this solution:
I recently purchased the 3 axis mach3 usb kit the motors have 8 different colored wires (no stripes on wire just solid color) all instructions have different colors. cannot find tutorals. does the mach 3 hook up same as planet? please let me know where I can find wiring diagram to hook up mach 3 usb BOB and motors (I am new to this kind of work projects)

The blackFoot uses the same electronics and motors as the blackToe (2'x4') machine. The only parts that change are the gantry horizontal structural parts which may be relatively easy for you to change. We can send you those parts if you are interested in a smaller unit.

Click the link to add information to this solution:
I have a Blackfoot that was purchased in 2017, after the purchase we moved and I haven’t been able to find room for it... would you be interested in buying it back or trading for something smaller. The Blackfoot and computer have never run but I did purchase it assembled. Thanks in advance, scott

Here are links to the sole pump and heat exchanger/fan. I am sending you amazon links sine I don't ahve listings of my pump and heat exchanger separately from my cooling system:
Pump: https://amzn.to/3R6zPbj
Fan/radiator (Heat exchanger): https://amzn.to/3UWOuqN

Click the link to add information to this solution:
I RECENTLY PURCHASED A REPALCEMENT 12V DC SWITCHING POWER SUPPLY, HOOKED IT UP BUR DID NOT THE PUMP AND RADIATOR. VERIFIED OUTPUT OF UNIT AT 12V. SO I'M ASSUMING ALSO NEED TO REPLACE CAN YOU SUPPLY ME LINK PURCHASE THEM?

Is this CNC related. If so, what controller are you using?

Additional Information:
I'm using the Mach 3/USB CNC interface board, with the Mach 3 software.

Additional Information:
Does the LED on the controller light up, or blink?

Additional Information:
I believe I've corrected the issue. I found that their are 2 spring like tabs on the female USB port. And take a sharp point like on a compass and gentle raise those tabs a bit. This tighten up the connection, and I never received an error from losing connection.

Click the link to add information to this solution:
It appears I have a connection issue with the USB port on my computer with the USB cord. I purchased a new cord but has the same issue. Is there anything I can do to correct this issue?

Yes, here is the URL for the parallel breakout board that we sell:

https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Click the link to add information to this solution:
can I purchase just the parallel controller board? I purchased the usb option 4 axis combo and would like to also try the system with my parallel port computer. Any help with this will be greatly appreciated; my goal is to implement mach4.

You can do raster and vector engraving on the greenBull laser/spindle combination. The methods of this process is not accomplished in the same way as the typical laser machines where CorelDRAW is used. The Mach3 laser plug-in can be used for the raster engraving and standard CNC g-code can be used for vector cutting and engraving.

The raster method will not be fast on the greenBull since the z-axis is heavy and there are inertial limitation on doing fast raster back and forth movement. Vector is the best use of this machine.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I am looking at purchasing the greenbull 5X system with the laser/spindle combination. Can the laser do both rastered engraving as well as vectored cutting with the same breakout board and software? If I have this wrong please let me know what would be needed to accompish this.

Has the tube functioned properly prior to this issue?

Click the link to add information to this solution:
I am having issues with the laser firing. Seems like there is an arc in the end of the tube where the elctrode is but i am not sure if i am doing something wrong.

In the scenario where the motors are not moving, do you see the red LED on the Mach3 USB controller blinking fast?

- If not, then there is a communication issue between the computer and the Mach3 USB controller.

- If you do see the blinking, then there is an issue between the Mach3 USB controller and the drivers, or a power supply issue (the power supply that is connected to the drivers that power the motors).

Additional Information:
20

Click the link to add information to this solution:
Asus Laptop win11 running Mach3USB and rnrmotion board. Sporadic event. Everything starts and looks correct. Readouts show motor movement with arrow keys, however, motors don't move. Came back 1 day later to resolve and everything worked fine. this has happened 3 time in the last year. I am having this problem right now. What should I do?

Send me an email so I can confirm the purchase. customerservice@gmail.com

Click the link to add information to this solution:
I purchased a brealout board a couple days ago and it does not show under my account as being purchased, the cash was drawn from me. I assumed I could look and see it in my account and get a tracking number when it is shipped

Make sure to check your supply lines. Air flow is especially important.

Click the link to add information to this solution:
hi, I atacched a laser system to my modified book machine. it worked fine for a few trials but for some reason has lost power and is not cutting through any more, it does engrave thou. what can I check for? I´ve tried everything I can think of.

I would recommend using a separate 24VDC power supply for the controller. The 24VDC that is connected to the controller is used for delicate input signals and output signals that control external devices. To keep interference and possible current and voltage fluctuations at a minimum due to the motor load, a separate power supply would be best.

Click the link to add information to this solution:
[575] Can the 24VDC supply used for the interface board be the same supply used for stepper drivers, or do you need separate power supplies? If not, does GND and DCM need to be isolated?