The Mach3 USB controller will work with M3/M4/M5 or M7/M8/M9 combinations. M10/M11 is not available with the controller.

Click the link to add information to this solution:
does the mach3 usb controller interface board support the M11/M10 command set

The Mach3 USB controller is specifically engineered to integrate seamlessly with Mach3's CNC control software. Easel, on the other hand, offers an all-in-one CAD/CAM solution along with machine control capabilities. While Easel can output standard G-code compatible with industry-standard post-processors, it can serve as a design tool when used in conjunction with Mach3 but not as the machine control software.

Click the link to add information to this solution:
[575] Will the Mach3 USB interface board support other software such as Easel?

In our experience, the backlash compensation is not an ideal mechanism to solve backlash issues. It is best to resolve the backlash issue mechanically regather than through software.

Boards that handle all instructions on its own chip (which is the case for this all other USB boards) take some control away from Mach3. Without Mach3 having granular control. With that said, we do not have experience with the backlash compensation with that particular board. Our experience with backlash compensation with other boards have resulted in very poor accuracy and undesirable geometrical moves.

Additional Information:
zokkj

Additional Information:
zokkj

Additional Information:
zokkj

Click the link to add information to this solution:
Mach3 USB Interface Board, Backlash Compensation in Mach3 is not working. Does this board support the backlash function?

I do not recommend using the Mach3 USB controller to be used with a torch height controller. There are only 4 inputs on the Mach3 USB controller. We have tried to interface a Proma THC to this board without success; however, we did not exhaust all possibilities.

I would recommend the Pokeys57CNC controller to connect the Proma THC as I have interfaced these two before and they work well together.
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
[575] Hello. Does this USB interface board thc? I have the proma 150.

The usb controller will only work with the planet-cnc software which is software that will work in Windows.

Click the link to add information to this solution:
Does USB Controller Breakout support Linux Ubuntu and does the software support command line interface (to control it with python scripts for example)

The usb controller will only work with the planet-cnc software which is software that will work in Windows.

Click the link to add information to this solution:
Does USB Controller Breakout support Linux Ubuntu and does the software support command line interface (to control it with python scripts for example)

The Mach3 100 kHz controller may be able to support the Sherline 1/2 pulse mode, but I have not tried it. There is no information in the documentation that is related to the parameter that can be set in Mach3 for the Sherline 1/2 pulse mode. You may be able to play with the available kHz ranges that the plugin allows to see if there is a pulse width that meets the Sherline 1/2 pulse mode specification.

Click the link to add information to this solution:
[575] Does the USB MACH3 controller support Sherline 1/2 pulse mode?

You have the ability to designate the 4th axis, commonly known as the A-axis, for rotary indexing operations when using a Mach3 USB controller.

To achieve this in Mach3, you'll need to:

Open the Mach3 software.
Navigate to "Config" and then to "Ports and Pins."
Go to the "Motor Outputs" tab.
Enable the A-axis and assign the respective Step and Direction pins.
Save your settings and exit the "Ports and Pins" dialog.
To calibrate the A-axis, go to "Settings" and use the "Set Steps Per Unit" option.

Click the link to add information to this solution:
[575] Does this board support indexing on mach3 turn? Planning to use it on a lathe and will do threading jobs

The Mach3 USB board will fit in the redLeaf, but you may need to modify the Plexiglas top for proper mounting. However, the redLeaf has the proper parallel GPIO on the motherboard for use with the Parallel breakout board. If you have a laser on the machine you are using, then I would urge you to maintain the parallel breakout board as the Mach3 USB board will not work correctly using the Z-direction pin and you will need to determine how to use the output pins onthe USB board to ensure proper laser functionality.

Click the link to add information to this solution:
Will Mach3 USB Interface board fit in my redleaf, in lieu of the breakout board that came with it?

Depending on the probe that you have, you should have two wires coming from the probe. One of those two wires will need to be connect to an input pin as shown in this wiring diagram (the diagram show the probe connected to pin I4):
https://www.buildyourcnc.com/Documents/Electric%20Wiring%20Diagram.pdf

The other pin is connected to V-. Please make sure that you have 24V connected to the V- and V+ on that side of the Mach3 USB board.

The way the probe works is when the probe is in contact with an object, a specific spring mechanism will cause the input pin to be connected to the V- (close the circuit). When Mach3 senses an active low on the input pin, mach3 knows that the probe has made contact (closed the circuit).

If your probe is used as a Z-Axis zero plate, then the concept is the same, but the end mill is connected to V- and the plate is connected to the input pin. If the plate comes in contact to the end mill, then the circuit is closed and mach3 will sense an active low on the input pin.

Click the link to add information to this solution:
Mach3 USB interface board. Could you please give me the correct wiring configuration for tool prob?

Yes, Mach3 (the software profram) will work with Windows 7, and windows 10 when coupled with the Mach3 USB interface. If you intend to use the parallel port driver, stick with Windows 7 in 32-bit mode.

Additional Information:
Rnrmotion.dll is a dynamic link library which is very similar in function to an executable program, or app. Since a dll is executable, malicious code can be embedded in that type of file, so windows will automatically flag all files of this type. You just need to make sure you are downloading from a trusted source. The emotion.dll file on our site is clean, but still run run windows defender against it to make sure.

Click the link to add information to this solution:
Why does Windows 10 block the RnRmotion.dill for Mach3 USB interface from being downloaded?

Rnrmotion.dll is a dynamic link library that is very similar in function to an executable program, or app. Since a dll is executable, malicious code can be embedded in that type of file, so windows will automatically flag all files of this type. You just need to make sure you are downloading from a trusted source. The emotion.dll file on our site is clean, but still, run windows defender against it to make sure.

Click the link to add information to this solution:
Why does Windows 10 block the RnRmotion.dill for Mach3 USB interface from being downloaded?

Planet-CNC is the control software. If you decide to use the USB controller, you will need to use the planet-CNC software as the control software. You will be able to use any of the CAM software applications with the planet-CNC control software.

Click the link to add information to this solution:
Can I use your USB interface board and Mach3 on my 3 axis CNC router?

Our MAch3 USB interface boards can be located here:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
I AM INTERESTED IN THE 3 AXIS COMBO USB OPTION. NOTICE YOU ENDORSE PLANET-CNC FOR USE WITH THIS BUT WILL MACH3 INTERFACE WELL BEAK OUT BOARD?

If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

Additional Information:
ur gay

Additional Information:

Click the link to add information to this solution:
MY COMPUTER DOES NOT HAVE A PARALLEL PORT. HOW DO I INTERFACE WITH THE BREAKOUT BOARD?

Yes, you can use a laptop if you have a controller that uses a USB, like the Mach3 USB card. If you don't have that, you can purchase that part here:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

If you have a controller board that connects to a 25 pin connector, modern laptops will not be able to connect to that port.

How old is your CNC computer system?

Additional Information:
The CNC computer system is 2013 (5 years). The built in video card went out. I will order the Mach3 USB card. Thank you.

Additional Information:
You're welcome

Click the link to add information to this solution:
The motherboard on the computer I bought from you went out. What would you suggest. I have a laptop, could I use it and use a Mach3 USB interface board?

The Mach3 USB interface card uses 5V (powered from the computer's USB) and a 24v to power the inputs, outputs and spindle control

the mach3 usb interface can be found here:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

But the mach3 usb does not absolutely need the 24V supply. The 24v supply is only needed if you will be using limit switches (I1-4), VFD controlled automatically and for use with the outputs (O1-4)


Additional Information:
The 36v 8.8 amp power supply we typically recommend is for powering the stepper motor drivers.

Click the link to add information to this solution:
Can I power the Mach3 USB interface 24V with a 48V power supply?

Planet-CNC is the control software. If you decide to use the USB controller, you will need to use the planet-CNC software as the control software. You will be able to use any of the CAM software applications with the planet-CNC control software.

Click the link to add information to this solution:
Would I be able to use the Mach3 CNC Control Software or any of the CNC CAM Software(BOBCAD/CAM,CAMBAM) if I choose to use the Planet-CNC USB Interface Board?

Our MAch3 USB interface boards can be located here:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
I am interested in the 3 axis combo USB option. I notice you endorse the Planet-CNC for use with this but will Mach3 interface well with the USB beak out Board?