The Greenbull machine can cut a very wide variety of materials ranging from foam to aluminum. We recommend the use of our 2.2kW spindle to allow the greatest flexibility. Aside from that, the most important thing is to use an appropriate end mill for the material you are cutting and to use appropriate speeds and feed rates.



BYCNC Response:
Our 40W laser can cut up to about 1/4" materials ranging from wood and acrylic down through lighter materials such as leather, fabric, foam, etc. Speed and final cut are greatly enhanced by an air assist upgrade. We also offer an 80W laser which has approximately twice the capabilities of the 40W.

Additional Information:

Click the link to add information to this solution:
WHAT MATERIALS CAN THE GREENBULL MACHINE CUT? LASER ETCH?

The greenBull can range is routing width sizes of 5 feet and 6 feet. The blackFoot has a 4 foot routing width.

Previous Solution:
The greenBull machine has a sturdier gantry than the blackFoot, so you can be more agressive with the cutting feedrate (cutting speed). The blackFoot is also a good machine, but it all comes down to the speed at which you want to produce the fabrication

The spindle is also highly recommended for it's quietness and easier cleanup (no fan blowing the dust in the air)

Additional Information:



Additional Information:

Click the link to add information to this solution:
SHOULD I SELECT THE GREENBULL OR BLACKFOOT CNC MACHINE?

You will need to build the table unit for your machine. There are instructions on how to do this at the bottom of the product page here, https://www.buildyourcnc.com/Item/cnc-machine-blackFoot-v4
There is no estimate on how much this will cost though, since there are too many variables involved to do this.

- PC with parallel port and USB port
- 20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
- 18awg stranded wires for power supply to drivers
- 24awg stranded wires for breakout board to drivers
(location and spacing of components varies from one person to another, so we do not provide cables/wires)
- General purpose extension cord (cut the female end off) to provide power to power supply
- USB cable to power breakout board
- Parallel cable to communicate to breakout board
- Router
- (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
- (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
- End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
- CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
- CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx

This answer is applicable to most of our machines with the exception of the greenLean and the blueChick since those machines are equipped with a table structure.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
IF I PURCHASE A GREENBULL 6X LONG Z CNC MACHINE KIT AND MACH3, WHAT ELSE WOULD BE REQUIRED TO ASSEMBLE THE WORKING MACHINE? HAVE CAD SOFTWARE.

You will need to build the table unit for your machine. There are instructions on how to do this at the bottom of the product page here, https://www.buildyourcnc.com/Item/cnc-machine-blackFoot-v4
There is no estimate on how much this will cost though, since there are too many variables involved to do this.

- PC with parallel port and USB port
- 20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
- 18awg stranded wires for power supply to drivers
- 24awg stranded wires for breakout board to drivers
(location and spacing of components varies from one person to another, so we do not provide cables/wires)
- General purpose extension cord (cut the female end off) to provide power to power supply
- USB cable to power breakout board
- Parallel cable to communicate to breakout board
- Router
- (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
- (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
- End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
- CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
- CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx

This answer is applicable to most of our machines with the exception of the greenLean and the blueChick since those machines are equipped with a table structure.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
If I purchase a greenBull 6X Long Z CNC Machine Kit and Mach3, what else would be required to assemble the working machine? I have CAD software.

The greenBull can range is routing width sizes of 5 feet and 6 feet. The blackFoot has a 4 foot routing width.

Previous Solution:
The greenBull machine has a sturdier gantry than the blackFoot, so you can be more agressive with the cutting feedrate (cutting speed). The blackFoot is also a good machine, but it all comes down to the speed at which you want to produce the fabrication

The spindle is also highly recommended for it's quietness and easier cleanup (no fan blowing the dust in the air)

Additional Information:



Additional Information:

Click the link to add information to this solution:
WHICH MACHINE SHOULD I BUY, THE GREENBULL OR BLACKFOOT?

If you use the 2.2kW spindle, it can cut at 3/4 inch or 19 mm deep with at least a 1/4" cutting diameter single flute end mill. You will get better results with larger diameter end mills, but that is the worst case scenario. I still recommend doing a finishing pass on the edge to make sure everything is perfect.

Click the link to add information to this solution:
CAN THE GREENBULL CUT 18MM BIRCH IN ONE PASS?

The greenBull 4X comes with all of the components and electronics to assemble the gantry of the machine. You will need to build the table. We provide the rails and roller chain for the X-axis (along the length of the table for full 8 feet of travel). You will need to provide some wire to connect the electronics and a computer to run the machine. You will also need to purchase the software that you will need to run the machine that matches how you will apply the machine. We suggest the mach3 control program. The CAM program is up to you as there are many options out there.

Click the link to add information to this solution:
I am interested in buying the greenBull 5X Long Z CNC Machine Kit, but it is not clear for me what is included in this kit. Is there anything else I need to get the machine work?

Gcode or digital files are not available for our machines.

Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I have the build your own CNC kit 3 Axis CNC Machine 2008, were can I get the Gcode or vector files for it ? I wanted to have it laser cut

Currently our greenBull can only accommodate a 40W laser tube due to the size and current mounts on the spindle/laser hybrid assembly!

However please contact 281-815-7701 for further assistance with the greenBull machine.

Click the link to add information to this solution:
I am interested in the GreenBull 4x8 CNC machine kit you have; I also wish to get the laser attachment but I was wondering if its possible to have the laser larger than a 40w, say in the 80-150w range?

The greenBull can range is routing width sizes of 5 feet and 6 feet. The blackFoot has a 4 foot routing width.

Previous Solution:
The greenBull machine has a sturdier gantry than the blackFoot, so you can be more agressive with the cutting feedrate (cutting speed). The blackFoot is also a good machine, but it all comes down to the speed at which you want to produce the fabrication

The spindle is also highly recommended for it's quietness and easier cleanup (no fan blowing the dust in the air)

Additional Information:



Additional Information:

Click the link to add information to this solution:
WHICH MACHINE SHOULD I BUY, GREENBULL OR BLACKFOOT?

Yes, that is not a problem at all. Give us a call.

Click the link to add information to this solution:
Can you custimize the 2'x4' CNC Machine Kit (blackToe v4.1) w/ 2.2kW Spindle into a 2'x3' Machine Kit?

Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

Some of the types of CNC electronics we will consider.

- We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

- We will repair or retrofit used CNC electronics.

- Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

Here is an example of CNC electronics that we worked on for a customer:

Click the link to add information to this solution:
Can you repair the electronics on my CNC machine?

The greenBull 4X comes with all of the components and electronics to assemble the gantry of the machine. You will need to build the table. We provide the rails and roller chain for the X-axis (along the length of the table for full 8 feet of travel). You will need to provide some wire to connect the electronics and a computer to run the machine. You will also need to purchase the software that you will need to run the machine that matches how you will apply the machine. We suggest the mach3 control program. The CAM program is up to you as there are many options out there.

Click the link to add information to this solution:
WHAT DOES THE GREENBULL KIT INCLUDE AND DO I NEED TO INCLUDE?

The roller chain lengths for the greenBull 4x is:
- 13 feet for each side of the X axis (total of 26 feet), and
- 6 feet for the Y-axis

Click the link to add information to this solution:
WHAT LENGTHS OF ROLLER CHAIN DO I USE FOR THE GREENBULL 4X CNC?

You can use the board5.nc as the expansion parts.

Additional Information:
20

Click the link to add information to this solution:
Where is the link for the expansion kit for the CNC Routing Machine Kit Version 1.3?

the greenBull can handle cutting aluminum as long as the correct bit (end mill) is used and the bit is cooled frequently to prevent chips from melting and causing damage to the bit or warping the material.

Click the link to add information to this solution:
Would your greenBull 6X CNC machine be suitable for cutting 2024T3 aircraft aluminium? Working on a kitlpane project and I need this capability.

The electronics combo with the sku of 101 on Amazon.com includes a parallel interface.

Click the link to add information to this solution:
I am looking at your 3 axis CNC machine kit(part #101) on Amazon. Is the interface on this kit USB?

You can expect a one week lead time for our machines.

Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
WHAT LEAD TIME CAN EXPECT FOR THE BLACKTOE MACHINE?

These machines are inherently dangerous. Before the machine moves, the machine should be clear of any person by a dimension of at the distance of a persons reach plus a few more feet. This is the policies we institute in our shop and what is recommend to all of our customers. Treat these machines as you would treat any major power tool in the shop.

With that said, you can certainly add some protective parts, but still keep folks away even with those installed. I would use the gantry side to do all of the mounting of the protective parts. Consider using sheet metal that you can bend and make a simple installation right on the gantry side.

Additional Information:

Click the link to add information to this solution:
THE CNC MACHINE IS UNSAFE WITH EXPOSED SPROCKETS THAT CAN DAMAGE FINGERS AND HAVE CLOTHING CAUGHT IN IT.