[ Log In ]
[ Register ]

Question #: 14802

Question: Can you repair the electronics on my CNC machine?

Current Solution

Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

Some of the types of CNC electronics we will consider.

- We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

- We will repair or retrofit used CNC electronics.

- Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

Here is an example of CNC electronics that we worked on for a customer:



This is the type of response that you can expect to receive after the CNC electronics are repaired or retrofitted to work under Mach3, Mach4 or LinuxCNC. You can see the entire work, which also shows the time involved. We also show what we were able to accomplish at the beginning of the video.

Respond:

Other Possible Solutions to this Question

  • Just purchased the book "Build Your Own CNC Machine". Can I get hardware and electronics kits and how?

    The electronics (stepper motors, drivers, power supply and interface board) can be found here:
    https://www.buildyourcnc.com/item/electronicsAndMotors-3axis-425-elcombo

    If your computer cannot connect to the parallel breakout board (the interface card), just make sure to inform us that you need the USB alternative.

    Click the link to respond:
    Just purchased the book "Build Your Own CNC Machine". Can I get hardware and electronics kits and how?

  • Do you repair cnc electronics from another manufacturer?

    Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

    Some of the types of CNC electronics we will consider.

    - We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

    - We will repair or retrofit used CNC electronics.

    - Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

    The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

    Here is an example of CNC electronics that we worked on for a customer:



    This is the type of response that you can expect to receive after the CNC electronics are repaired or retrofitted to work under Mach3, Mach4 or LinuxCNC. You can see the entire work, which also shows the time involved. We also show what we were able to accomplish at the beginning of the video.

    Click the link to respond:
    Do you repair cnc electronics from another manufacturer?

  • Can you supply an electronics package for a dual x-axis CNC machine (X, Y, Z)

    Yes, we have a 4 axis combo kit available under Motion Electronics.

    Click the link to respond:
    Can you supply an electronics package for a dual x-axis CNC machine (X, Y, Z)

  • Can you finish putting my CNC electronics together for me?

    Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

    Some of the types of CNC electronics we will consider.

    - We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

    - We will repair or retrofit used CNC electronics.

    - Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

    The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

    Here is an example of CNC electronics that we worked on for a customer:



    This is the type of response that you can expect to receive after the CNC electronics are repaired or retrofitted to work under Mach3, Mach4 or LinuxCNC. You can see the entire work, which also shows the time involved. We also show what we were able to accomplish at the beginning of the video.

    Click the link to respond:
    Can you finish putting my CNC electronics together for me?

  • I need my spindle and cnc electronics repaired. How can I fix it?

    Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

    Some of the types of CNC electronics we will consider.

    - We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

    - We will repair or retrofit used CNC electronics.

    - Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

    The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

    Here is an example of CNC electronics that we worked on for a customer:



    This is the type of response that you can expect to receive after the CNC electronics are repaired or retrofitted to work under Mach3, Mach4 or LinuxCNC. You can see the entire work, which also shows the time involved. We also show what we were able to accomplish at the beginning of the video.

    Click the link to respond:
    I need my spindle and cnc electronics repaired. How can I fix it?

  • Can I get building plans for the machines, electronics and programming?

    The available options for the blackFoot, is only structural components with hardware, and structure components/hardware with electronic components.
    However we currently do not have any plans available for public use/distribution.

    Click the link to respond:
    Can I get building plans for the machines, electronics and programming?

  • I bought a used cnc router. Can you make the electronics work?

    Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

    Some of the types of CNC electronics we will consider.

    - We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

    - We will repair or retrofit used CNC electronics.

    - Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

    The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

    Here is an example of CNC electronics that we worked on for a customer:



    This is the type of response that you can expect to receive after the CNC electronics are repaired or retrofitted to work under Mach3, Mach4 or LinuxCNC. You can see the entire work, which also shows the time involved. We also show what we were able to accomplish at the beginning of the video.

    Click the link to respond:
    I bought a used cnc router. Can you make the electronics work?

  • Which electronics package is required for the CNC machine from the book designs?

    The book design uses all NEMA 23/24 motors which can be found here:
    https://buildyourcnc.com/item/electronicsAndMotors-3axis-425-elcombo

    I recommend the Mach3 USB option as you will be able to use the USB connection for control.

    If you are planning to build from the plans developed by the folks over at Woodsmith Magazine which is loosely based on the book design, use this electronics package:
    https://buildyourcnc.com/item/electronicsAndMotors-3axis-heavy-gantry-elcombo

    Click the link to respond:
    Which electronics package is required for the CNC machine from the book designs?

  • Hi there. I am looking upgrading the electronics on my 8x4 machine. Do you do your pre wired kits without the motors?

    Yes, we can provide a pre-wired electronics listed on this page:

    https://www.buildyourcnc.com/AssembledElectronics.aspx

    If you require these without the motors, please give us a call so your motors can be wired correctly and you can purchase the system without the motors.

    Currently, the office is closed due to flooding in the area, but we plan to re-open very shortly.

    Click the link to respond:
    Hi there. I am looking upgrading the electronics on my 8x4 machine. Do you do your pre wired kits without the motors?

  • I would like to use Mach3 instead of the software for my CNC router. Can you fix the electronics for me?

    Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

    Some of the types of CNC electronics we will consider.

    - We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

    - We will repair or retrofit used CNC electronics.

    - Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

    The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

    Here is an example of CNC electronics that we worked on for a customer:



    This is the type of response that you can expect to receive after the CNC electronics are repaired or retrofitted to work under Mach3, Mach4 or LinuxCNC. You can see the entire work, which also shows the time involved. We also show what we were able to accomplish at the beginning of the video.

    Click the link to respond:
    I would like to use Mach3 instead of the software for my CNC router. Can you fix the electronics for me?

  • Patrick have you ever considered using a air powered cabinet cooler for the electronics of the machine?

    The components that cause heat in the CNC electronics are the drivers. These drivers contain heat sinks and if enclosed within a space that does not have some type of air exchange, these driver may overheat. A simple fan, like the ones in a computer case is sufficient to provide this air exchange if installed properly. Keeping positive air pressure within the cabinet provides this air exchange and would not allow particles within this area.

    To provide positive air pressure, install a cooling fan on a side of this enclosure oriented so that the air is moving into the enclosure. The air will need a place to escape and the position of these places are important to make sure the air passes the heat sinks of the drivers.

    An air powered cabinet cooler may be more than is needed.

    Click the link to respond:
    Patrick have you ever considered using a air powered cabinet cooler for the electronics of the machine?

  • I received the electronics for book build cnc machine. I need to know how much weight the z-axis motor can hold since my (craftsman) router seems to be heavy. It is 2HP with variable speed

    The motor is helped by the mechanical leverage of the screw. The 425 oz-in motors that are included in the standard electronics combo has very high torque for that type of machine. You will have no problem using that motor for the book machine.

    We use that motor for very heavy spindles on the blackToe and blackFoot CNC Machine kits.

    You will need to do the mechanical leverage calculation along with the torque of the motor to determine the actual weight it will lift. The calculation will need to consider the type and pitch of the screw and it would also consider the gravity constant of 9.8 m/s/s.

    If you need me to determine this formula and work out the calculation based on the screw you are using, please let me know.

    Additional Information:
    thank you for the reply. I would be really good to know the calculation. The lead screw is 1/2" diameter with 13 TPI. Please provide the calculation. And one more question. If I am cutting 18mm MDF with 6mm cutting bit (so 6mm pass), what can be the maximum speed rate of cutting and spindle speed of router?
    thank you

    Click the link to respond:
    I received the electronics for book build cnc machine. I need to know how much weight the z-axis motor can hold since my (craftsman) router seems to be heavy. It is 2HP with variable speed

  • The electronics for my current cnc machine has a 36v 8.8 amp power supply. Is this power supply sufficient to power my new Mach3 USB interface?

    The Mach3 USB interface card uses 5V (powered from the computer's USB) and a 24v to power the inputs, outputs and spindle control

    the mach3 usb interface can be found here:

    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    But the mach3 usb does not absolutely need the 24V supply. The 24v supply is only needed if you will be using limit switches (I1-4), VFD controlled automatically and for use with the outputs (O1-4)


    Additional Information:
    The 36v 8.8 amp power supply we typically recommend is for powering the stepper motor drivers.

    Click the link to respond:
    The electronics for my current cnc machine has a 36v 8.8 amp power supply. Is this power supply sufficient to power my new Mach3 USB interface?

  • Can I send used CNC electronics to you for a retrofit?

    Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

    Some of the types of CNC electronics we will consider.

    - We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

    - We will repair or retrofit used CNC electronics.

    - Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

    The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

    Here is an example of CNC electronics that we worked on for a customer:



    This is the type of response that you can expect to receive after the CNC electronics are repaired or retrofitted to work under Mach3, Mach4 or LinuxCNC. You can see the entire work, which also shows the time involved. We also show what we were able to accomplish at the beginning of the video.

    Click the link to respond:
    Can I send used CNC electronics to you for a retrofit?

  • where can I find the videos to connect the cnc electronics?

    The electronics and wiring videos are located under the tutorials section (click Tutorials on the top menu. The Title is "CNC Electronics and Wiring". The actual link to these videos is: https://www.buildyourcnc.com/CNCElectronicsandWiring.aspx

    Additional Information:
    You will also find the electronic wiring videos for the USB controller at: https://www.buildyourcnc.com/tutorials/tutorial-Electronics-USB-Interface-Wiring

    Click the link to respond:
    where can I find the videos to connect the cnc electronics?

  • Correct kit of motors and electronics, I bough a book in Amazons kindle to build a CNC, this book mention a kit of motors and electronics for parallel port, I want to use USB, can you suggest me the correct kit fot this machine.

    Dealing with our scratch Build kit/BYO CNC Book Kit, you will use our basic 3 axis electronics kit (https://buildyourcnc.com/item/electronicsAndMotors-3axis-425-elcombo). Now dealing with the Breakout Board, the book specifies the parallel port BoB, but you can use the USB BoB and use Planet-CNC rather than using Mach 3 or Linux-CNC as your control software.

    Click the link to respond:
    Correct kit of motors and electronics, I bough a book in Amazons kindle to build a CNC, this book mention a kit of motors and electronics for parallel port, I want to use USB, can you suggest me the correct kit fot this machine.

  • What can I do if my cnc electronics doesn't work?

    Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

    Some of the types of CNC electronics we will consider.

    - We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

    - We will repair or retrofit used CNC electronics.

    - Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

    The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

    Here is an example of CNC electronics that we worked on for a customer:



    This is the type of response that you can expect to receive after the CNC electronics are repaired or retrofitted to work under Mach3, Mach4 or LinuxCNC. You can see the entire work, which also shows the time involved. We also show what we were able to accomplish at the beginning of the video.

    Click the link to respond:
    What can I do if my cnc electronics doesn't work?

  • My cnc electronics does not turn on with my spindle. How can I fix it?

    Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

    Some of the types of CNC electronics we will consider.

    - We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

    - We will repair or retrofit used CNC electronics.

    - Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

    The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

    Here is an example of CNC electronics that we worked on for a customer:



    This is the type of response that you can expect to receive after the CNC electronics are repaired or retrofitted to work under Mach3, Mach4 or LinuxCNC. You can see the entire work, which also shows the time involved. We also show what we were able to accomplish at the beginning of the video.

    Click the link to respond:
    My cnc electronics does not turn on with my spindle. How can I fix it?

  • DOES THE PLUG AND PLAY ELECTRONICS COMPUTER FOR 3 AXIS CNC MACHINE HAVE ENOUGH MEMORY RAM ADDITIONAL SOFTWARE (BOBCAD-CAM, BOBART, MACH3) TO BE ADDED FUNCTION WELL?

    The plug and play system does have enough memory for additional software. The redLeaf comes standard with a 1TB hard drive.

    Click the link to respond:
    DOES THE PLUG AND PLAY ELECTRONICS COMPUTER FOR 3 AXIS CNC MACHINE HAVE ENOUGH MEMORY RAM ADDITIONAL SOFTWARE (BOBCAD-CAM, BOBART, MACH3) TO BE ADDED FUNCTION WELL?

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.