[ Log In ]
[ Register ]

Question #: 2272

Question: Are the Assembled CNC Electronics Systems compatible with a laptop?

Current Solution

Our Computer CNC-systems, come integrated with all the required electronics (motherboard, HDD, PSU). Only input devices(mouse, keyboard, monitor) and software are required to be purchased separately, to have a complete ready to go system.

Here (https://www.buildyourcnc.com/AssembledElectronics.aspx) you can see the available option of including windows 7 to be installed with our computer system.

You can use an external HDD or Flash-drive, to transfer data from your laptop/computer to the built in computer system.

Respond:

Other Possible Solutions to this Question

  • Are the 3 axis electronics combos with the Mach 3 USB breakout board compatible with Mach 4?

    These boards are compatible with Mach3 only at this time. We will be adding a Mach4 board in the near future.

    Click the link to add information to this solution:
    Are the 3 axis electronics combos with the Mach 3 USB breakout board compatible with Mach 4?

  • If I purchase the [blackToe 2x4 v4.1 CNC Machine Kit - USB Electronics - Table Included] all I would need for this CNC to be fully operational is a laptop with mach 3 software and a router. Is this correct?

    if you purchased the USB interface, you will need planet-cnc software rather than Mach3, and you will need a usb cable to connect the usb interface to the computer.

    The blackToe 2x4 CNC Machine Kit with optional table will need wire to connect the electronics. Don't forget to get some end mills to use for cutting the intended material.


    Additional Information:



    Additional Information:



    Additional Information:

    Click the link to add information to this solution:
    If I purchase the [blackToe 2x4 v4.1 CNC Machine Kit - USB Electronics - Table Included] all I would need for this CNC to be fully operational is a laptop with mach 3 software and a router. Is this correct?

  • Do you sell the 3 axis electronics combo , for heavy gantry , with the new Planet CNC usb controller ?

    Unfortunately, we don't sell the planet-cnc controller anymore. They made a change to their software that prohibits us from creating the open source board.

    We do sell three other boards that may work for you.

    The Pokeys57CNC board is the mose feature rich and will work with both Mach3 and Mach4:
    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

    The MAch3 USB board is a good inexpensive interface that will work well if you need the interface to be USB only:
    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    Our in-house parallel breakout board (ytou need a parallel port for this interface to work):
    https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay
    Most motherboards have the parallel port connector on the motherboard, but not as a connector on the back of the computer case.

    Click the link to add information to this solution:
    Do you sell the 3 axis electronics combo , for heavy gantry , with the new Planet CNC usb controller ?

  • [50] this combo is compatible for a CNC with a 48" x 48" work area

    Yes, you can use these electronics to move a machine that has an area of 48" x 48". If you are looking for faster jogging, you can upgrade the motor to this one: https://www.buildyourcnc.com/item/electronicsAndMotors-nema34-1100ozin

    Click the link to add information to this solution:
    [50] this combo is compatible for a CNC with a 48" x 48" work area

  • I bought a CNC router used and I need help retrofitting the electronics.

    Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

    Some of the types of CNC electronics we will consider.

    - We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

    - We will repair or retrofit used CNC electronics.

    - Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

    The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

    Here is an example of CNC electronics that we worked on for a customer:



    This is the type of response that you can expect to receive after the CNC electronics are repaired or retrofitted to work under Mach3, Mach4 or LinuxCNC. You can see the entire work, which also shows the time involved. We also show what we were able to accomplish at the beginning of the video.

    Click the link to add information to this solution:
    I bought a CNC router used and I need help retrofitting the electronics.

  • IS THE MACH3 SOFTWARE COMPATIBLE WITH 3 AXIS MOTION CONTROL COMBO KITS? PLANET CNC MENTIONED AS BEING COMPATIBLE.

    Mach 3 is compatible with our electronic combo's that include the Parallel Breakout Board.
    Planet-CNC is compatible with our electronic combo's that included our USB Breakout Board.

    The parallel breakout board is compatible to a wide variety of software control packages. The USB interface board that we sell can only be used with the Planet-cnc control software.

    If you are concerned with your computer (desktop) not having a parallel port, one can be purchased and inserted into a PCI slot on the motherboard. Some motherboard also come with a parallel port header (connector) on the motherboard and a simple cable can be connected to this connector to get that functionality on the computer. The former solution of getting a parallel port adapter card to plug into the motherboard is probable the easiest and least expensive option.

    Additional Information:


    Additional Information:
    Is the mach 3 software compatible with kollmorgen s200 servo motors and controllers?

    Click the link to add information to this solution:
    IS THE MACH3 SOFTWARE COMPATIBLE WITH 3 AXIS MOTION CONTROL COMBO KITS? PLANET CNC MENTIONED AS BEING COMPATIBLE.

  • DOES ANY OF THE SOFTWARE THAT COMES WITH IT COMPATIBLE MAC 10.6?

    There are several CAD/CAM programs out there for MacOS. Here is a list of a few: http://www.macuser.de/forum/f53/3d-2d-cad-395058/#post4499316
    I've also read good things about punchCAD: http://www.punchcad.com/
    Of course, there is always SketchUp if you are in a pinch. There are a few CAM plugins for SketchUp as well, but I've never used them, so I can't vouch for them.

    CAD/CAM will get you as far as designing your parts and producing the g-code, but if you also want to run the CNC machine with your Mac, you will need a piece of software similar to Mach3 or EMC to run the g-code. I haven't been able to find anything like these programs that runs on Mac, so you may have to run Mach3 or EMC in Windows using Boot Camp or a virtual machine such as VMware or Parallels.

    Personally, I would use the Mac to do all the CAD/CAM, then use a cheap PC to run the CNC machine.

    Additional Information:


    Additional Information:
    EasyDNC for OSX
    www.dnc-x.com

    Additional Information:


    Additional Information:
    Hi guys I’m new to the cnc and I’m beginning to learn how to operate and cad-cam software also my cnc runs on Mach3 my questions is if I should use MacBook to do all designs if I can have all this software to run on Mac or I have to use windows software to operate it? I have separate small computer connected to the cnc table who have Mach3 on it please help. Also if you know any other software much easy for beginners please let me know thank you guys!
    My email if needed is r1jastrzebski@gmail.com

    Additional Information:


    Additional Information:
    Hi , thank you for your advise!

    Additional Information:
    Hi , thank you for your advise!

    Additional Information:
    Hi , thank you for your advise!

    Additional Information:
    Hi , thank you for your advise!

    Additional Information:

    Click the link to add information to this solution:
    DOES ANY OF THE SOFTWARE THAT COMES WITH IT COMPATIBLE MAC 10.6?

  • Are the VFDs and pumps compatible with the european electric circuit (230V/50Hz) and what kind of connectors will be delivered?

    The VFD (Variable Frequency Drive) is not supplied with plugs, cable or connectors. You provide the cable and power plug or connector for the VFD. All you need to do is get an extension cable and expose the three wires of the cable and connect them to R, T and Ground. Please see the datasheet on this page for wiring information: https://www.buildyourcnc.com/item/spindle-inverter-2!2kw-spindle-novfd

    Our pumps only have a 110 volt input, so you will need to purchase the pump in your country.

    Click the link to add information to this solution:
    Are the VFDs and pumps compatible with the european electric circuit (230V/50Hz) and what kind of connectors will be delivered?

  • what does the plans, hardware, electronics and mechanical option consists of for a CNC router?

    The plans/hardware/electronics/mechanical includes everything but the wood structural components that can be cut by the customer. This plans/hardware option includes all of the electronics, like motors, drivers, controller, and all of the cables and wires to connect all of the electronics together. The mechanical components include shafts, couplings, linear rails, bearing blocks, sprockets, lead screws, etc. The hardware consists of all of the screws nuts, insert nuts, cross dowels, etc, to assemble all of the structural, mechanical, and electronics together.

    Click the link to add information to this solution:
    what does the plans, hardware, electronics and mechanical option consists of for a CNC router?

  • Which electronics package is required for the CNC machine from the book designs?

    The book design uses all NEMA 23/24 motors which can be found here:
    https://buildyourcnc.com/item/electronicsAndMotors-3axis-425-elcombo

    I recommend the Mach3 USB option as you will be able to use the USB connection for control.

    If you are planning to build from the plans developed by the folks over at Woodsmith Magazine which is loosely based on the book design, use this electronics package:
    https://buildyourcnc.com/item/electronicsAndMotors-3axis-heavy-gantry-elcombo

    Click the link to add information to this solution:
    Which electronics package is required for the CNC machine from the book designs?

  • Can you repair the electronics on my CNC machine?

    Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

    Some of the types of CNC electronics we will consider.

    - We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

    - We will repair or retrofit used CNC electronics.

    - Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

    The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

    Here is an example of CNC electronics that we worked on for a customer:



    This is the type of response that you can expect to receive after the CNC electronics are repaired or retrofitted to work under Mach3, Mach4 or LinuxCNC. You can see the entire work, which also shows the time involved. We also show what we were able to accomplish at the beginning of the video.

    Click the link to add information to this solution:
    Can you repair the electronics on my CNC machine?

  • WHERE ARE THE ELECTRONICS WIRING VIDEOS?

    The blackFoot CNC machine kit does not include a table. The table can be made as long or shot as you need. for instance, if you are looking for a travel of 4 fet x 4 feet, then the table will need to be about 6 feet long to get the full 4 feet of travel.

    The electronics are very straight forward using the connection diagram for the breakout board that you select. Use the videos for a general idea and then use the connection diagram to verify the correct connections for the interface of your choosing.

    Yes,the USB interface replaces the breakout board, but remember that you will need to use the planet-cnc software with the USB interface.

    Additional Information:
    The electronics does accompany the cnc machine kits as long as you select the option "with electronics". There are option to purchase the machines without electronics and that would be necessary if you either have your own electronics, or you prefer the plug and play cnc computer system we call the redLeaf, or redSprout. This will also be necessary if you prefer the electronics that use the USB interface rather than the parallel interface.

    Additional Information:

    Click the link to add information to this solution:
    WHERE ARE THE ELECTRONICS WIRING VIDEOS?

  • WHERE ARE THE ELECTRONICS WIRING VIDEOS?

    The electronics and wiring videos are located under the tutorials section (click Tutorials on the top menu. The Title is "CNC Electronics and Wiring". The actual link to these videos is: https://www.buildyourcnc.com/CNCElectronicsandWiring.aspx

    Additional Information:
    You will also find the electronic wiring videos for the USB controller at: https://www.buildyourcnc.com/tutorials/tutorial-Electronics-USB-Interface-Wiring

    Click the link to add information to this solution:
    WHERE ARE THE ELECTRONICS WIRING VIDEOS?

  • YOUR CNC SOFTWARE COMPATIBLE WITH MAC?

    There are several CAD/CAM programs out there for MacOS. Here is a list of a few: http://www.macuser.de/forum/f53/3d-2d-cad-395058/#post4499316
    I've also read good things about punchCAD: http://www.punchcad.com/
    Of course, there is always SketchUp if you are in a pinch. There are a few CAM plugins for SketchUp as well, but I've never used them, so I can't vouch for them.

    CAD/CAM will get you as far as designing your parts and producing the g-code, but if you also want to run the CNC machine with your Mac, you will need a piece of software similar to Mach3 or EMC to run the g-code. I haven't been able to find anything like these programs that runs on Mac, so you may have to run Mach3 or EMC in Windows using Boot Camp or a virtual machine such as VMware or Parallels.

    Personally, I would use the Mac to do all the CAD/CAM, then use a cheap PC to run the CNC machine.

    Additional Information:


    Additional Information:
    EasyDNC for OSX
    www.dnc-x.com

    Additional Information:


    Additional Information:
    Hi guys I’m new to the cnc and I’m beginning to learn how to operate and cad-cam software also my cnc runs on Mach3 my questions is if I should use MacBook to do all designs if I can have all this software to run on Mac or I have to use windows software to operate it? I have separate small computer connected to the cnc table who have Mach3 on it please help. Also if you know any other software much easy for beginners please let me know thank you guys!
    My email if needed is r1jastrzebski@gmail.com

    Additional Information:


    Additional Information:
    Hi , thank you for your advise!

    Additional Information:
    Hi , thank you for your advise!

    Additional Information:
    Hi , thank you for your advise!

    Additional Information:
    Hi , thank you for your advise!

    Additional Information:

    Click the link to add information to this solution:
    YOUR CNC SOFTWARE COMPATIBLE WITH MAC?

  • Would you sell a kit that has all of the hardware and electronics with CNC plans for the table and gantry? Some of have access to a CNC temporarily (TechShop) but want one of our own.

    We currently do not sell any plan's for any of our machines, only for our scratch and build kit.

    Click the link to add information to this solution:
    Would you sell a kit that has all of the hardware and electronics with CNC plans for the table and gantry? Some of have access to a CNC temporarily (TechShop) but want one of our own.

  • Looking to buy a black toe 2x4, what electronics are included ? Is it optional with USB-interface? And for last do you ship to sweden?
  • Just purchased the book "Build Your Own CNC Machine". Can I get hardware and electronics kits and how?

    The electronics (stepper motors, drivers, power supply and interface board) can be found here:
    https://www.buildyourcnc.com/item/electronicsAndMotors-3axis-425-elcombo

    If your computer cannot connect to the parallel breakout board (the interface card), just make sure to inform us that you need the USB alternative.

    Click the link to add information to this solution:
    Just purchased the book "Build Your Own CNC Machine". Can I get hardware and electronics kits and how?

  • I would like to use Mach3 instead of the software for my CNC router. Can you fix the electronics for me?

    Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

    Some of the types of CNC electronics we will consider.

    - We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

    - We will repair or retrofit used CNC electronics.

    - Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

    The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

    Here is an example of CNC electronics that we worked on for a customer:



    This is the type of response that you can expect to receive after the CNC electronics are repaired or retrofitted to work under Mach3, Mach4 or LinuxCNC. You can see the entire work, which also shows the time involved. We also show what we were able to accomplish at the beginning of the video.

    Click the link to add information to this solution:
    I would like to use Mach3 instead of the software for my CNC router. Can you fix the electronics for me?

  • I have a 4x8 CNC and would like to cut my own parts for the Blackfoot. What is the price for the plans and the electronics ?

    The available options for the blackFoot, is only structural components with hardware, and structure components/hardware with electronic components.
    However we currently do not have any plans available for public use/distribution.

    Click the link to add information to this solution:
    I have a 4x8 CNC and would like to cut my own parts for the Blackfoot. What is the price for the plans and the electronics ?

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.