Mach 3 is compatible with our electronic combo's that include the Parallel Breakout Board.
Planet-CNC is compatible with our electronic combo's that included our USB Breakout Board.

The parallel breakout board is compatible to a wide variety of software control packages. The USB interface board that we sell can only be used with the Planet-cnc control software.

If you are concerned with your computer (desktop) not having a parallel port, one can be purchased and inserted into a PCI slot on the motherboard. Some motherboard also come with a parallel port header (connector) on the motherboard and a simple cable can be connected to this connector to get that functionality on the computer. The former solution of getting a parallel port adapter card to plug into the motherboard is probable the easiest and least expensive option.

Additional Information:


Additional Information:
Is the mach 3 software compatible with kollmorgen s200 servo motors and controllers?

Click the link to add information to this solution:
IS THE MACH3 SOFTWARE COMPATIBLE WITH 3 AXIS MOTION CONTROL COMBO KITS? PLANET CNC MENTIONED AS BEING COMPATIBLE.

Yes, with caveats. This kit includes a controller that will not be compatible, but if you use another type of controller that has web based control, you can use these electronics. Here is a list of web based control for CNC:

- Easel: The web-based software from Inventables can be accessed through Safari or other macOS-compatible web browsers.

- bCNC: A Python-based GRBL CNC command sender, although you may need to jump through some hoops to get it to run on macOS.

- Universal Gcode Sender: A Java-based software that should run on macOS if you have the Java Runtime Environment installed.

- CNCjs: Another web-based interface that you can run on macOS using Node.js.

Click the link to add information to this solution:
[50] Is there a software control package that will work with Axis Electronics Combo (For Heavy Gantry) for apple os.

I recommend using a wireless pendant rather than one that is wired to the controller.

Here is a link to one on Amazon.com: https://amzn.to/3r3AfTm

This is an affiliate link.

Click the link to add information to this solution:
[596] I am new to CNCs, curious to know what I need to look for in a pendant that would be compatible with this board and Mach4?

Our Computer CNC-systems, come integrated with all the required electronics (motherboard, HDD, PSU). Only input devices(mouse, keyboard, monitor) and software are required to be purchased separately, to have a complete ready to go system.

Here (https://www.buildyourcnc.com/AssembledElectronics.aspx) you can see the available option of including windows 7 to be installed with our computer system.

You can use an external HDD or Flash-drive, to transfer data from your laptop/computer to the built in computer system.

Click the link to add information to this solution:
Are the Assembled CNC Electronics Systems compatible with a laptop?

There are several CAD/CAM programs out there for MacOS. Here is a list of a few: http://www.macuser.de/forum/f53/3d-2d-cad-395058/#post4499316
I've also read good things about punchCAD: http://www.punchcad.com/
Of course, there is always SketchUp if you are in a pinch. There are a few CAM plugins for SketchUp as well, but I've never used them, so I can't vouch for them.

CAD/CAM will get you as far as designing your parts and producing the g-code, but if you also want to run the CNC machine with your Mac, you will need a piece of software similar to Mach3 or EMC to run the g-code. I haven't been able to find anything like these programs that runs on Mac, so you may have to run Mach3 or EMC in Windows using Boot Camp or a virtual machine such as VMware or Parallels.

Personally, I would use the Mac to do all the CAD/CAM, then use a cheap PC to run the CNC machine.

Additional Information:


Additional Information:
EasyDNC for OSX
www.dnc-x.com

Additional Information:


Additional Information:
Hi guys I’m new to the cnc and I’m beginning to learn how to operate and cad-cam software also my cnc runs on Mach3 my questions is if I should use MacBook to do all designs if I can have all this software to run on Mac or I have to use windows software to operate it? I have separate small computer connected to the cnc table who have Mach3 on it please help. Also if you know any other software much easy for beginners please let me know thank you guys!
My email if needed is r1jastrzebski@gmail.com

Additional Information:


Additional Information:
Hi , thank you for your advise!

Additional Information:
Hi , thank you for your advise!

Additional Information:
Hi , thank you for your advise!

Additional Information:
Hi , thank you for your advise!

Additional Information:

Click the link to add information to this solution:
YOUR CNC SOFTWARE COMPATIBLE WITH MAC?

Our MAch3 USB interface boards can be located here:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
Is the USB hub ready for use with Mach3 at this time, or just Planet CNC?

There are several CAD/CAM programs out there for MacOS. Here is a list of a few: http://www.macuser.de/forum/f53/3d-2d-cad-395058/#post4499316
I've also read good things about punchCAD: http://www.punchcad.com/
Of course, there is always SketchUp if you are in a pinch. There are a few CAM plugins for SketchUp as well, but I've never used them, so I can't vouch for them.

CAD/CAM will get you as far as designing your parts and producing the g-code, but if you also want to run the CNC machine with your Mac, you will need a piece of software similar to Mach3 or EMC to run the g-code. I haven't been able to find anything like these programs that runs on Mac, so you may have to run Mach3 or EMC in Windows using Boot Camp or a virtual machine such as VMware or Parallels.

Personally, I would use the Mac to do all the CAD/CAM, then use a cheap PC to run the CNC machine.

Additional Information:


Additional Information:
EasyDNC for OSX
www.dnc-x.com

Additional Information:


Additional Information:
Hi guys I’m new to the cnc and I’m beginning to learn how to operate and cad-cam software also my cnc runs on Mach3 my questions is if I should use MacBook to do all designs if I can have all this software to run on Mac or I have to use windows software to operate it? I have separate small computer connected to the cnc table who have Mach3 on it please help. Also if you know any other software much easy for beginners please let me know thank you guys!
My email if needed is r1jastrzebski@gmail.com

Additional Information:


Additional Information:
Hi , thank you for your advise!

Additional Information:
Hi , thank you for your advise!

Additional Information:
Hi , thank you for your advise!

Additional Information:
Hi , thank you for your advise!

Additional Information:

Click the link to add information to this solution:
DOES ANY OF THE SOFTWARE THAT COMES WITH IT COMPATIBLE MAC 10.6?

To select a 4 axis NEMA 17 motor and driver combination, you will need the following:

- Four (4) NEMA 17 motors: https://buildyourcnc.com/item/electronicsAndMotors-nema17-62ozin-NEWBIEHACK-motors-stepping_motor-62_ozin

- Four (4) drivers, either the 2.5A: https://buildyourcnc.com/item/motion%20electronics-steppermotordriver-newbiehack-Motor_Drivers-2!5_Amp_modular or the 3.0A: https://buildyourcnc.com/item/electronicsAndMotors-stepper-driver-3!0a

- One (1) Power supply, either the 24V or 36V (recommended): https://buildyourcnc.com/item/electronicsAndMotors-power-supply

- Finally, an interface is needed, either parallel, or USB. The USB works with planet-cnc software only. The parallel interface works with all major CNC control software: https://buildyourcnc.com/category/breakout

Click the link to add information to this solution:
Can you supply a quote for a 4 axis combo kit with NEMA 17 Motors

Unfortunately, we don't sell the planet-cnc controller anymore. They made a change to their software that prohibits us from creating the open source board.

We do sell three other boards that may work for you.

The Pokeys57CNC board is the mose feature rich and will work with both Mach3 and Mach4:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

The MAch3 USB board is a good inexpensive interface that will work well if you need the interface to be USB only:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Our in-house parallel breakout board (ytou need a parallel port for this interface to work):
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay
Most motherboards have the parallel port connector on the motherboard, but not as a connector on the back of the computer case.

Click the link to add information to this solution:
Do you sell the 3 axis electronics combo , for heavy gantry , with the new Planet CNC usb controller ?

These boards are compatible with Mach3 only at this time. We will be adding a Mach4 board in the near future.

Click the link to add information to this solution:
Are the 3 axis electronics combos with the Mach 3 USB breakout board compatible with Mach 4?

Yes, the kit for this machine can be modified for the travel/routing dimensions of 12"x16"x6".

Click the link to add information to this solution:
[126] Could we customize this model to a smaller format with a higher Z? 12" x 16" x 6" Routing Area?

It's best to design a machine specifically for a lathe rather than adapting an existing machine kit to an existing lathe. If you are interested in us designing a machine like this, let us know.

Click the link to add information to this solution:
Can any of your CNC kits be adapted to work with a manual wood lathe?

For the NEMA 34 stepper motor with a maximum current of 6 amps, 18 AWG wire would technically be sufficient. According to the American Wire Gauge (AWG) standard, 18 AWG wire can handle up to around 10 amps of current in chassis wiring and around 16 amps in power transmission. If you are considering running a very long length of cable from the driver to the stepper motor, you may want to consider using 16 AWG.

As for the spindle, this wire gauge is well-suited. There are three phase shifts, each at 120 degrees and each conductor is carrying only 1/3 of the power. At 220v, 2200 watts / 220 V = 10 amps. 1/3 of 10 amps is 3.333 amps, so each conductor will be have a load of 3.33 amps.

Click the link to add information to this solution:
[801] Is this enough rating for a Nema 34 motor with max 6 amps? Also what about a 220V 2200Watt Spindle?

We currently do not have any Nema motor's with a .375"/3/8" shaft diameter. The motors in stock 100 oz, 425 oz, with a 1/4" input shaft. Our 651 oz, with a 1/2" input shaft.

Click the link to add information to this solution:
Your combo kits don't specify whether they are standard NEMA motors. I need Nema 34 with a .375 shaft diameter. Which 3 axis kit work for these requirements?

Our MAch3 USB interface boards can be located here:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
I AM INTERESTED IN THE 3 AXIS COMBO USB OPTION. NOTICE YOU ENDORSE PLANET-CNC FOR USE WITH THIS BUT WILL MACH3 INTERFACE WELL BEAK OUT BOARD?

Yes, this 4th axis system will work with the Masso controller. The 4th axis has a standard stepper motor. You will need a driver between the Masso controller and the stepper motor.

Click the link to add information to this solution:
[410] Will this work with the OneFinity Elite series with the MASSO controller?

Our USB breakout board, will not work with Mach 4! The USB BoB is specifically designed to work with Planet-CNC.


Additional Information:

Click the link to add information to this solution:
will mach4 software work with planet CNC breakoutboard?

SketchUcam will output gcode which standard CNC control software will typically interpret, execute and control CNC machines. So, there is no problem using SketchUcam. However, our CNC machine control software that use our CNC machine interface boards require Windows OS, of Linux. The Mach3 USB board will only run with Mach3 control software which runs under the Windows OS. The parallel breakout board can run under Windows or Linux OS and the computer must contain a parallel port.

Click the link to add information to this solution:
I would like to know if your breakout board and driver boards are compatible with MAC OS X working with Sketch Up pro using SketchUcam ?

Hi. The HIWIN spec rail will fit standard M5 screws. If you are using non standard screws with wide heads, or pan heads that are a bit larger than a standard round heads, then it may not fit. Make sure to source screws that have standard round heads, or socket heads for fastening the 20mm HIWIN spec rails.

Click the link to add information to this solution:
I purchased some of your 20mm Hiwin Linear Rails. M5 bolts do not fit flush. The head stands out. Is the spec sheet out of date? What bolts will fit this rail AND T Nuts compatible with 8020's 15 series extrusions? Thanks.