The files and hardware option for our machines has been removed from the site due to the following reasons:
Difficulty for the end use of the files and the challenges (and time/money) on our side to assist in using these files.
The abuse of these files over the internet.
Ultimately may reduce the sales of machines keeping us in business.
Sadly, this is what has come out of our company attempting to be open; however, the machines sold on this site is still far lower in price than the competition for the quality that we provide as we have a great desire to engender the cottage industry to fulfill their need for low end manufacturing. My sincere apologies if this causes any inconvenience.

Additional Information:
NO, is not possible, I can help with the shipping cost

Additional Information:

Click the link to add information to this solution:
IT POSSIBLE TO BUY THE CAD FILES FOR BLACK FOOT MACHINE, MECHANICAL PARTS AND ELECTRONICS BUT NOT WOODEN PARTS, SAVE SHIPPING COSTS? IN THAT CASE I WOULD INSTRUCT SOMEONE MILL ME.

The whiteAnt is no longer sold; the information on the website is to support legacy customers. We have spoken with you and are sending the materials that you need.

Click the link to add information to this solution:
I am having difficulty with the wiring on the White Ant. The latest electronics that I received don't seem to be anything like the book or even the tutorials. For instance, the three stepper drivers need 6 pin connectors and ribbon cable. How are they wired? There was no thermocouple wire included. Thanks,

Our electronics contains a switchable power supply that allows you to switch the input mains voltage between 115 volts (110/120) and 230 volts (220/240). the hertx range is not specified, but there are capacitors to smooth out standard frequencies to enable DC output.

Click the link to add information to this solution:
hi, what about, if I buy from you some elecronic parts like (3 Axis Electronics Combo) and I use them here in france , where the electric voltage is 220V 50Hertz ? thats gonna works? thanks

What electronics do you have at the moment? Depending on your machine, you will need a minimum of 3 stepper motors and 3 drivers (unless your heavy axis requires two stepper motors and two drivers). You will also need an interface board that is capable of providing three inputs for the THC (Torch Height Controller), THC on, THC up and THC down, and outputs for firing the torch. I would recommend the Pokeys57CNC interface for the primary interface. This interface will connect to the stepper motor drivers and the THC. The Pokeys57CNC can also communicate via USB or Ethernet.

Click the link to add information to this solution:
Looking for electronics for a plasmacam table. It's going to to be a 5'x10' table with x,y,z axis. Will be running on windows ten with a hypertherm powermax45 xp plasma cutter. Any information or links would be greatly appreciated!

In our 3-Axis electronics kit, the power supply's provided are capable of both 110V-220V. You have the capability to switch between both in case you might decide to run 220v in the near future or will relocate where 110v is being used.

Additional Information:
Connect spindle to the board



Additional Information:



Additional Information:

Click the link to add information to this solution:
In the 3 Axis Electronics Combo, what is the AC input of the power supply (110v or 220v??). is it possible to specify a certain voltage when ordering?

Here is a list of the parts needed to get the electronics combo functioning (parallel or USB interface options):

- 22 or 24 gauge stranded hookup wire to connect all of the drivers to the USB or parallel interface (terminal to terminal connections),
- 18 gauge stranded hookup wire to connect the drivers to the power supply,
- a power cable (extension cord) to connect from the power outlet to the power supply,
- 4 conductor cable to connect the drivers to the stepper motors,
- a USB cable to connect from the computer to the USB interface (or for power to the parallel interface),
- for the parallel interface, a parallel cable is needed (male to male db-25),
- a computer (for parallel interface, the computer will need a parallel port and if the computer does not contain a parallel interface, the motherboard may have a header for it, or you can purchase a parallel adapter to plug into the motherboard, very inexpensive),
- cnc control software: for the USB interface, you will need planet-cnc software, for the parallel interface, you can use any industry standard cnc control software (the typical is Mach3 for Windows, or EMC2 or Linuxcnc for Linux (Linuxcnc.org).

5v power supply is not needed. The 5 volts signal level power is derived from the computer through USB on both types of interfaces.

Click the link to add information to this solution:
What else to I need to purchase along with the "3 Axis Electronics Combo w/ USB Interface Board" to get the electronics up and running? (software, 5V power supply, 4-conductor wire, etc.)

I have not heard of different versions of g-code, but ArtCAM would be able to give you the answer to this question, if their software is specifying that there are different versions.

Additional Information:
20

Click the link to add information to this solution:
I'm using ArtCam with my Black Toe. What Gcode version do you choose to work with EMC2

Yes, with caveats. This kit includes a controller that will not be compatible, but if you use another type of controller that has web based control, you can use these electronics. Here is a list of web based control for CNC:

- Easel: The web-based software from Inventables can be accessed through Safari or other macOS-compatible web browsers.

- bCNC: A Python-based GRBL CNC command sender, although you may need to jump through some hoops to get it to run on macOS.

- Universal Gcode Sender: A Java-based software that should run on macOS if you have the Java Runtime Environment installed.

- CNCjs: Another web-based interface that you can run on macOS using Node.js.

Click the link to add information to this solution:
[50] Is there a software control package that will work with Axis Electronics Combo (For Heavy Gantry) for apple os.

Make sure all your bolts/screws are tighten correctly and if using a lead screw make sure your anti-backlash nut is not offset. Now a default setting will be 10101100 for your driver dip switch settings and in motor tuning (mach3) 1600 steps per, 400.02 velocity, 4 in acceleration. now the acceleration and velocity can be adjusted to move your machine faster, but if set to high they could stall. Make sure you have the correct wiring from your motor to your driver (https://www.buildyourcnc.com/Documents/PN.SM60HT86-2008BF-U%20(inhouse%20PN.60BYGH303-13)%20(1).pdf).

Click the link to add information to this solution:
I have your Nema 24 electronics kit and am having problems with the Z axis dropping over time. I am using a PC 8902 motor. Any ideas on what the problem is? What should be the motor tuning values in Mach3? Thanks

I have very detailed wiring videos for the Pokeys57CNC controller on the pokeys57CNC controller webpage: https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
[50] I purchased 3 Axis Heavy Gantry Electronics /w Pokeys57CNC controller (Mach3 and 4 Compatible) and Cable Pack I plan to use Mach 3 do You have a wiring diagram Thanks

The overall size of the machine, really depends on both the area available to you and also the overall size of material being used. Now our larger machines (blackFoot, greenBull, greenLean) can cut all the materials mentioned above, and if equipped with our 2.2kW spindle you will be accurate up to ten thousandths of an inch.
Our greenBull machine does have an option for a long-z axis, that was especially designed to cut foam, but depending on the overall size it might not be a requirement for the specified request.

Click the link to add information to this solution:
I HAVE A SIGN SHOP AND WE NEED CUT ALUMINUM, PLEXIGASS, FOAM AND OTHER MATERIALS FOR SIGNS. CAN YOU TELL ME WHAT MACHINE WE NEED? I LOOKING 4'X8' OR 5' X 10'

The gantry sides, gantry bridge parts, two 1/2" rods, two 1/2" ID bearings, two 1/2" ID 12 tooth sprockets, and extra roller chain.

Click the link to add information to this solution:
WHAT IS INCLUDED IN THE BLACK TOE TO FOOT UPGRADE?

The maximum length we can ship is a total of 78" inches. However we can send your required length in portions. Please refer to adding the total items you require to your cart to get a visualized amount and shipping cost.

Click the link to add information to this solution:
Regarding 1/2" 5 start and 10 TPI ACME precision lead screw, what the maximum length you can ship within USA? I'm looking for something like 100" and I could use a 1" screw if available. Please include estimated price. Thanks.

You can use our shopping cart to determine the shipping. Add the machine and the parts you want to purchase, enter your shipping address and click on the Calculate Shipping Button to get a price for shipping. The shipping charges are determined directly from the carriers at the time of pressing that button.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Hi, I live in Australia and am looking at purchasing the Blacktooth laser cutter and engraver. I am wondering what the cost to ship to Australia would be?

The dimensions of the optional table are 73" x 34".

Click the link to add information to this solution:
What are the dimensions for a black toe torsion box? The machine dimensions are https://www.buildyourcnc.com/FAQ/1178 but I do not know the required overhang. I assume the overhang needs to be 3/4 inch ...

Artsoft (Also called Newfangled Solutions, Inc.) creates Mach3 and Mach3 along with other CNC related software. They are still in business. I noticed that the https seems to not work, so their SSL may have lapsed (2/19/2019). It is safe to use their website; however, if you do purchase on their site while their SSL is down, it's best to use their PayPal link to do the transaction.

Additional Information:
Or you can purchase the software from us.

Additional Information:
I would recommend Mach4 for the control software.

Click the link to add information to this solution:
Is Artsoft is out of Bussiness ? I am looking fo 64bit software , was going to use Mach4, so what would you recomend ? thanks John

The leadscrew length for the greenBull long Z-axis is 47 inches.

Additional Information:

Click the link to add information to this solution:
BUILDING ONE OF YOUR GREENBULL 6X LONG AND 2.2 KILOWATT SPINDLE DOES NOT FIT. SEEMS LEAD SCREW YOU SENT WITH KIT IS SHORT 42" LOOKS LIKE IT NEEDS TO BE 5 OR 6 INCH LONGER. THIS CORRECT? WHAT THE NEEDED LENGTH FOR UNIT?

If your motors are hot to the touch, this is normal. Current is being drawn by the motor coils as the motor moves and as the motor stays at a position. If the motor is not using the current in the coils to move (holding it's position), the energy will be translated as heat (rather than motion, sound or light). Even while moving, some of the energy will be lost as heat. Remember that energy cannot be created nor destroyed.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I HAVE FOLLOWED ALL THE "CNC ELECTRONICS 1 - 9" VIDEOS AND I'M USING ALMOST EXACT SAME COMPONENTS (MOTORS RUN SOUND GOOD) BUT MOTORS ARE RUNING VERY HOT IN JUST 15MIN WITH NO LOAD DONE SOMETHING WRONG OR DO STEPPERS HOT?

Conceptually it is straightforward to predict the radiofrequency (RF) exposure intensity at any point in the vicinity of a cellular radio base station antenna. Simply multiply the effective radiation power times the inverse square of the distance times the relative gain of the antenna in the direction of the interest. The relative gain in different directions is know as the antenna radiation pattern and is usually available from the antenna manufacturer in graphical or tabular form.

Unfortunately, in real life the calculations involved in base station antenna evaluations are quite complex and require expert knowledge and experience to deal with the many parameters that are involved. An excellent reference summarizing this process is the Federal Communications Commission OET Bulletin No. 65 titled "Evaluating Compliance With FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields," available on the Federal Communications Commission (FCC) website.

To assess the RF hazards associated with handheld cell phones it is necessary to predict the rate of absorption in the body of radiofrequency energy, a parameter called the specific absorption rate (SAR). This is a very complex calculation, and cell phone manufacturers often rely on measurements of SAR in fluid-filled cylinders or plastic containers in the shape of a head. The FCC requires cell phone manufacturers to provide this data to FCC. You can obtain the data for your model phone on the the FCC's website. Unfortunately only cell phones manufactured in the last couple years are listed here.

As to your question about keeping RF exposures within the safety code, please read the other questions posted on this website this matter. Cellular radio products that meet FCC requirements will be within the guidelines established by safety standards organizations for users' and public exposure to RF radiation fields.

Gary H. Zeman, ScD, CHP

Click the link to add information to this solution:
FIRST OF ALL, THANKS FOR DESIGNING A WONDERFUL SITE. MY QUESTION IS: HOW DO YOU CALCULATE EME (ELECTROMAGNETIC EMISSIONS) AROUND THE TRANSMITTER (ANTENNA) AT ANY GIVEN POINT AND WHAT ARE MEASURES TO KEEP IT UNDER SAFETY CODE?