[ Log In ]
[ Register ]

Question #: 14799

Question: Can you finish putting my CNC electronics together for me?

Current Solution

Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

Some of the types of CNC electronics we will consider.

- We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

- We will repair or retrofit used CNC electronics.

- Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

Here is an example of CNC electronics that we worked on for a customer:



This is the type of response that you can expect to receive after the CNC electronics are repaired or retrofitted to work under Mach3, Mach4 or LinuxCNC. You can see the entire work, which also shows the time involved. We also show what we were able to accomplish at the beginning of the video.

Respond:

Other Possible Solutions to this Question

  • I have a blueChick version 4.2 CNC Machine with no schematics for it is there anyway possibly i can get them so i can finish putting my cnc together

    To assemble the blueChick v4.2, you will need two sets of instructions, the assembly instructions for the main body and mechanicals of the CNC machine, and the instructions to connect and test all of the electronics.

    The assembly instructions are located at this URL towards the bottom of the page (click on each picture to get a larger view):

    https://www.buildyourcnc.com/blueChickVersion42CNCMachineKit.aspx

    The instructions to connect and test the electronics can be found at this URL:

    https://www.buildyourcnc.com/CNCElectronicsandWiring.aspx

    Click the link to respond:
    I have a blueChick version 4.2 CNC Machine with no schematics for it is there anyway possibly i can get them so i can finish putting my cnc together

  • I would like to use Mach3 instead of the software for my CNC router. Can you fix the electronics for me?

    Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

    Some of the types of CNC electronics we will consider.

    - We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

    - We will repair or retrofit used CNC electronics.

    - Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

    The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

    Here is an example of CNC electronics that we worked on for a customer:



    This is the type of response that you can expect to receive after the CNC electronics are repaired or retrofitted to work under Mach3, Mach4 or LinuxCNC. You can see the entire work, which also shows the time involved. We also show what we were able to accomplish at the beginning of the video.

    Click the link to respond:
    I would like to use Mach3 instead of the software for my CNC router. Can you fix the electronics for me?

  • Can I send used CNC electronics to you for a retrofit?

    Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

    Some of the types of CNC electronics we will consider.

    - We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

    - We will repair or retrofit used CNC electronics.

    - Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

    The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

    Here is an example of CNC electronics that we worked on for a customer:



    This is the type of response that you can expect to receive after the CNC electronics are repaired or retrofitted to work under Mach3, Mach4 or LinuxCNC. You can see the entire work, which also shows the time involved. We also show what we were able to accomplish at the beginning of the video.

    Click the link to respond:
    Can I send used CNC electronics to you for a retrofit?

  • Can you supply an electronics package for a dual x-axis CNC machine (X, Y, Z)

    Yes, we have a 4 axis combo kit available under Motion Electronics.

    Click the link to respond:
    Can you supply an electronics package for a dual x-axis CNC machine (X, Y, Z)

  • Can you repair the electronics on my CNC machine?

    Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

    Some of the types of CNC electronics we will consider.

    - We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

    - We will repair or retrofit used CNC electronics.

    - Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

    The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

    Here is an example of CNC electronics that we worked on for a customer:



    This is the type of response that you can expect to receive after the CNC electronics are repaired or retrofitted to work under Mach3, Mach4 or LinuxCNC. You can see the entire work, which also shows the time involved. We also show what we were able to accomplish at the beginning of the video.

    Click the link to respond:
    Can you repair the electronics on my CNC machine?

  • I bought a used cnc router. Can you make the electronics work?

    Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

    Some of the types of CNC electronics we will consider.

    - We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

    - We will repair or retrofit used CNC electronics.

    - Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

    The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

    Here is an example of CNC electronics that we worked on for a customer:



    This is the type of response that you can expect to receive after the CNC electronics are repaired or retrofitted to work under Mach3, Mach4 or LinuxCNC. You can see the entire work, which also shows the time involved. We also show what we were able to accomplish at the beginning of the video.

    Click the link to respond:
    I bought a used cnc router. Can you make the electronics work?

  • I need my spindle and cnc electronics repaired. How can I fix it?

    Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

    Some of the types of CNC electronics we will consider.

    - We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

    - We will repair or retrofit used CNC electronics.

    - Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

    The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

    Here is an example of CNC electronics that we worked on for a customer:



    This is the type of response that you can expect to receive after the CNC electronics are repaired or retrofitted to work under Mach3, Mach4 or LinuxCNC. You can see the entire work, which also shows the time involved. We also show what we were able to accomplish at the beginning of the video.

    Click the link to respond:
    I need my spindle and cnc electronics repaired. How can I fix it?

  • What can I do if my cnc electronics doesn't work?

    Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

    Some of the types of CNC electronics we will consider.

    - We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

    - We will repair or retrofit used CNC electronics.

    - Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

    The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

    Here is an example of CNC electronics that we worked on for a customer:



    This is the type of response that you can expect to receive after the CNC electronics are repaired or retrofitted to work under Mach3, Mach4 or LinuxCNC. You can see the entire work, which also shows the time involved. We also show what we were able to accomplish at the beginning of the video.

    Click the link to respond:
    What can I do if my cnc electronics doesn't work?

  • can you please tell me what is supported voltage and amperage for this combo connector https://buildyourcnc.com/item/electronicsandmotors-connector-round-female-male-4pin

    The 4 pin male and female motor connectors are rated by their manufacturer at 100VAC and 2A.

    Click the link to respond:
    can you please tell me what is supported voltage and amperage for this combo connector https://buildyourcnc.com/item/electronicsandmotors-connector-round-female-male-4pin

  • My cnc electronics does not turn on with my spindle. How can I fix it?

    Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

    Some of the types of CNC electronics we will consider.

    - We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

    - We will repair or retrofit used CNC electronics.

    - Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

    The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

    Here is an example of CNC electronics that we worked on for a customer:



    This is the type of response that you can expect to receive after the CNC electronics are repaired or retrofitted to work under Mach3, Mach4 or LinuxCNC. You can see the entire work, which also shows the time involved. We also show what we were able to accomplish at the beginning of the video.

    Click the link to respond:
    My cnc electronics does not turn on with my spindle. How can I fix it?

  • If I bring my 6090 with Huanyang VFD/spindle and G540 can you wire vfd/540 together and get it talking to mach3 for me?

    We can provide support to electronic components that we sell. We are unable to connect or diagnose electronics that we don't offer.

    Additional Information:
    We can provide solutions to products that we sell. For instance, we can inform how to connect a spindle's VFD to Mach3 using a RS-485 serial communication method.

    Click the link to respond:
    If I bring my 6090 with Huanyang VFD/spindle and G540 can you wire vfd/540 together and get it talking to mach3 for me?

  • The instructions for the 3-axis combo at https://buildyourcnc.com/item/electronicsAndMotors-3axis-425-elcombo seem to be missing. Can you look into that.

    To wire the CNC electronics, use the tutorial for the specific interface board you are using.

    If you have the parallel breakout board, use this tutorial:
    https://buildyourcnc.com/CNCElectronicsandWiring.aspx

    If you have the USB interface board, use this tutorial:
    https://buildyourcnc.com/tutorials/tutorial-Electronics-USB-Interface-Wiring

    Click the link to respond:
    The instructions for the 3-axis combo at https://buildyourcnc.com/item/electronicsAndMotors-3axis-425-elcombo seem to be missing. Can you look into that.

  • Just purchased the book "Build Your Own CNC Machine". Can I get hardware and electronics kits and how?

    The electronics (stepper motors, drivers, power supply and interface board) can be found here:
    https://www.buildyourcnc.com/item/electronicsAndMotors-3axis-425-elcombo

    If your computer cannot connect to the parallel breakout board (the interface card), just make sure to inform us that you need the USB alternative.

    Click the link to respond:
    Just purchased the book "Build Your Own CNC Machine". Can I get hardware and electronics kits and how?

  • Do you sell the 3 axis electronics combo , for heavy gantry , with the new Planet CNC usb controller ?

    Unfortunately, we don't sell the planet-cnc controller anymore. They made a change to their software that prohibits us from creating the open source board.

    We do sell three other boards that may work for you.

    The Pokeys57CNC board is the mose feature rich and will work with both Mach3 and Mach4:
    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

    The MAch3 USB board is a good inexpensive interface that will work well if you need the interface to be USB only:
    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    Our in-house parallel breakout board (ytou need a parallel port for this interface to work):
    https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay
    Most motherboards have the parallel port connector on the motherboard, but not as a connector on the back of the computer case.

    Click the link to respond:
    Do you sell the 3 axis electronics combo , for heavy gantry , with the new Planet CNC usb controller ?

  • I need to replace the fried electronics box for my 6090 wood router. Do you offer a play and play, no wiring required, kit? If yes, how much? If no, can you recommend one?

    Yes, we offer a CNC electronics assembled package called the redFly, redLead and redSprout. If you already have a computer, I would recommend the redFly. You would still need to add connectors to the ends of your motor cable.

    https://www.buildyourcnc.com/item/cnc-computer-system-redFly

    Click the link to respond:
    I need to replace the fried electronics box for my 6090 wood router. Do you offer a play and play, no wiring required, kit? If yes, how much? If no, can you recommend one?

  • where can I find the videos to connect the cnc electronics?

    The electronics and wiring videos are located under the tutorials section (click Tutorials on the top menu. The Title is "CNC Electronics and Wiring". The actual link to these videos is: https://www.buildyourcnc.com/CNCElectronicsandWiring.aspx

    Additional Information:
    You will also find the electronic wiring videos for the USB controller at: https://www.buildyourcnc.com/tutorials/tutorial-Electronics-USB-Interface-Wiring

    Click the link to respond:
    where can I find the videos to connect the cnc electronics?

  • Do you repair cnc electronics from another manufacturer?

    Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

    Some of the types of CNC electronics we will consider.

    - We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

    - We will repair or retrofit used CNC electronics.

    - Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

    The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

    Here is an example of CNC electronics that we worked on for a customer:



    This is the type of response that you can expect to receive after the CNC electronics are repaired or retrofitted to work under Mach3, Mach4 or LinuxCNC. You can see the entire work, which also shows the time involved. We also show what we were able to accomplish at the beginning of the video.

    Click the link to respond:
    Do you repair cnc electronics from another manufacturer?

  • what does the plans, hardware, electronics and mechanical option consists of for a CNC router?

    The plans/hardware/electronics/mechanical includes everything but the wood structural components that can be cut by the customer. This plans/hardware option includes all of the electronics, like motors, drivers, controller, and all of the cables and wires to connect all of the electronics together. The mechanical components include shafts, couplings, linear rails, bearing blocks, sprockets, lead screws, etc. The hardware consists of all of the screws nuts, insert nuts, cross dowels, etc, to assemble all of the structural, mechanical, and electronics together.

    Click the link to respond:
    what does the plans, hardware, electronics and mechanical option consists of for a CNC router?

  • I would like to design my own CNC router around one of your electronics bundles, either the 3 Axis - Heavy Gantry or 3 Axis - All Large Motors. Do you have the data sheets for the motors so that I can use the dimensions in my model?

    You can find the datasheets to our motors be going to the the stepping motor category page https://www.buildyourcnc.com/category/nema and selecting the motor. This will bring you to the product page for the motor and all of the motor information will be found there.

    Click the link to respond:
    I would like to design my own CNC router around one of your electronics bundles, either the 3 Axis - Heavy Gantry or 3 Axis - All Large Motors. Do you have the data sheets for the motors so that I can use the dimensions in my model?

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.