[ Log In ]
[ Register ]

Question #: 13505

Question: I have a blueChick version 4.2 CNC Machine with no schematics for it is there anyway possibly i can get them so i can finish putting my cnc together

Current Solution

To assemble the blueChick v4.2, you will need two sets of instructions, the assembly instructions for the main body and mechanicals of the CNC machine, and the instructions to connect and test all of the electronics.

The assembly instructions are located at this URL towards the bottom of the page (click on each picture to get a larger view):

https://www.buildyourcnc.com/blueChickVersion42CNCMachineKit.aspx

The instructions to connect and test the electronics can be found at this URL:

https://www.buildyourcnc.com/CNCElectronicsandWiring.aspx

Respond:

Other Possible Solutions to this Question

  • I AM PUTTING TOGETHER THE BLACKFOOT AND USING A PORTER CABLE ROUTER. CONFUSED ON HOW TO RELAY ROUTETR WITH USB BOARD. IS THERE ANOTHER SWITCH THAT GOES BETWEEN BOARD ROUTER SO PLANET CNC CAN TURN PERHAPS VACUUM OFF?

    We are currently working on a relay board that will connect to USB breakout board, and the router/spindle for both the on/off function. Unfortunately we still do not have it completed or ready to be placed on our website, but it is in the final stages of testing. Please check back regularly for updated stock!

    Here is a link to a tutorial for a DIY relay circuit:



    There is no vacuum control on the Planet-CNC program, however you could use the same concept of the router/spindle on/off using the relay circuit. Although you will have to use either the flood or mist function for the vacuum.

    Click the link to respond:
    I AM PUTTING TOGETHER THE BLACKFOOT AND USING A PORTER CABLE ROUTER. CONFUSED ON HOW TO RELAY ROUTETR WITH USB BOARD. IS THERE ANOTHER SWITCH THAT GOES BETWEEN BOARD ROUTER SO PLANET CNC CAN TURN PERHAPS VACUUM OFF?

  • ARE THERE STILL VIDEOS THAT CAN WATCH AS PUT THIS TOGETHER, I'LL BUY THEM IF HAVE TO, VERY FUSTURATED WITH ELECTROCTICS AND WIRING PART.
  • Can you finish putting my CNC electronics together for me?

    Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

    Some of the types of CNC electronics we will consider.

    - We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

    - We will repair or retrofit used CNC electronics.

    - Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

    The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

    Here is an example of CNC electronics that we worked on for a customer:



    This is the type of response that you can expect to receive after the CNC electronics are repaired or retrofitted to work under Mach3, Mach4 or LinuxCNC. You can see the entire work, which also shows the time involved. We also show what we were able to accomplish at the beginning of the video.

    Click the link to respond:
    Can you finish putting my CNC electronics together for me?

  • I am putting together the Blackfoot and I am using a porter cable router. I am confused on how to relay the routetr with the USB board. is there another relay switch that goes between the USB board and the router so that planet CNC can turn the router and perhaps the vacuum on and off?

    We are currently working on a relay board that will connect to USB breakout board, and the router/spindle for both the on/off function. Unfortunately we still do not have it completed or ready to be placed on our website, but it is in the final stages of testing. Please check back regularly for updated stock!

    Here is a link to a tutorial for a DIY relay circuit:



    There is no vacuum control on the Planet-CNC program, however you could use the same concept of the router/spindle on/off using the relay circuit. Although you will have to use either the flood or mist function for the vacuum.

    Click the link to respond:
    I am putting together the Blackfoot and I am using a porter cable router. I am confused on how to relay the routetr with the USB board. is there another relay switch that goes between the USB board and the router so that planet CNC can turn the router and perhaps the vacuum on and off?

  • Is there a version of the pick and place machine with larger pcb area? 5.75 by 15.25 inches isn't quite enough, perhaps 9 by 15.25.

    Not at this time, however, we are in development of a more advanced version of our pick and place machine with a larger pcb area. More details to come early next year (2017)

    Click the link to respond:
    Is there a version of the pick and place machine with larger pcb area? 5.75 by 15.25 inches isn't quite enough, perhaps 9 by 15.25.

  • I purchased a 4ft X 8ft Blackfoot CNC machine in 2015 and to this date have not been able to use it. How can I get some help. Thank u
  • I am having trouble connecting the cambam program with my Mach3 to my 4X8 Blackfoot CNC machine. Where can I get help on this issue. Have had my machine since 2015 and have not been able to use it. Thank you

    CamBam specifically creates the g-code (machining operations) instructions to be loaded into Mach3. Make sure in your CamBam g-code file parameters, you are using the Mach3 post processor. If you have already done this, let me know. If you are not sure how to do this, let me know.

    Click the link to respond:
    I am having trouble connecting the cambam program with my Mach3 to my 4X8 Blackfoot CNC machine. Where can I get help on this issue. Have had my machine since 2015 and have not been able to use it. Thank you

  • I just wanted to know what I can expect to pay to build the blackFoot 4'x8' CNC machine, excluding computer, software and router? Is the kit complete or do I have to purchase additional items to finish?

    You will need to build the table unit for your machine. There are instructions on how to do this at the bottom of the product page here, https://www.buildyourcnc.com/Item/cnc-machine-blackFoot-v4
    There is no estimate on how much this will cost though, since there are too many variables involved to do this.

    - PC with parallel port and USB port
    - 20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
    - 18awg stranded wires for power supply to drivers
    - 24awg stranded wires for breakout board to drivers
    (location and spacing of components varies from one person to another, so we do not provide cables/wires)
    - General purpose extension cord (cut the female end off) to provide power to power supply
    - USB cable to power breakout board
    - Parallel cable to communicate to breakout board
    - Router
    - (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
    - (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
    - End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
    - CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
    - CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx

    This answer is applicable to most of our machines with the exception of the greenLean and the blueChick since those machines are equipped with a table structure.

    Click the link to respond:
    I just wanted to know what I can expect to pay to build the blackFoot 4'x8' CNC machine, excluding computer, software and router? Is the kit complete or do I have to purchase additional items to finish?

  • I have a blueChick 13"x24" or 13"x36" Desktop CNC Router Kit v3.0 (Timing Belt) that I've assembled but never was able to get it running. Can BuildYourCNC assist me in selling this machine? Do you have used machine offerings on your site?

    We would highly recommend using our forums to sell you machine buildyourtools.com.
    We currently do not have a page or option to allow our customers to sell our machines, you can also contact us at customerservice@buildyourcnc.com, for further assistance dealing with the machine and in regards to selling it.

    Click the link to respond:
    I have a blueChick 13"x24" or 13"x36" Desktop CNC Router Kit v3.0 (Timing Belt) that I've assembled but never was able to get it running. Can BuildYourCNC assist me in selling this machine? Do you have used machine offerings on your site?

  • I have the build your own CNC kit 3 Axis CNC Machine 2008, were can I get the Gcode or vector files for it ? I wanted to have it laser cut
  • I have just purchased a 4x8 Greenbull system second-hand. Are there any schematics for table dimensions and rail-mounting available so that I can build a table? (previous owner disassembled)

    Actual table dimension: 4'x8' is 56.078"x 121.50" (the overhang in the illustrations should be 3/4" thick)
    To determine the frame dimensions, first consider using the frame height shown of almost 3' (2.86'). The width of the frame should be 4" narrower than the dimension from rail edge to rail edge (6X rail to rail is 80.078"). This will provide a 2" overhang on both sides (4X frame width should be 56.078").
    The length of the frame should be 4" shorter than the desired length of the rails to provide a 2" overhang on both ends. The travel length will be 20" shorter than the rail length due to the space occupied by the gantry sides.
    Two long pieces of 3/4" material will need to be placed on top of the frame with the 2" overhang on the sides and the end. These long strips of material will receive the rails and the chain mounts on the ends.


    Link:
    https://www.buildyourcnc.com/Item/cnc-machine-greenBull-v4-4X

    Click the link to respond:
    I have just purchased a 4x8 Greenbull system second-hand. Are there any schematics for table dimensions and rail-mounting available so that I can build a table? (previous owner disassembled)

  • I received the electronics for book build cnc machine. I need to know how much weight the z-axis motor can hold since my (craftsman) router seems to be heavy. It is 2HP with variable speed

    The motor is helped by the mechanical leverage of the screw. The 425 oz-in motors that are included in the standard electronics combo has very high torque for that type of machine. You will have no problem using that motor for the book machine.

    We use that motor for very heavy spindles on the blackToe and blackFoot CNC Machine kits.

    You will need to do the mechanical leverage calculation along with the torque of the motor to determine the actual weight it will lift. The calculation will need to consider the type and pitch of the screw and it would also consider the gravity constant of 9.8 m/s/s.

    If you need me to determine this formula and work out the calculation based on the screw you are using, please let me know.

    Additional Information:
    thank you for the reply. I would be really good to know the calculation. The lead screw is 1/2" diameter with 13 TPI. Please provide the calculation. And one more question. If I am cutting 18mm MDF with 6mm cutting bit (so 6mm pass), what can be the maximum speed rate of cutting and spindle speed of router?
    thank you

    Click the link to respond:
    I received the electronics for book build cnc machine. I need to know how much weight the z-axis motor can hold since my (craftsman) router seems to be heavy. It is 2HP with variable speed

  • with the blueChick v4.2 can any software be used or doo we need to purchase a lic key from the manufacture of the control board for 75 bucks

    If you have the USB controller you will need to purchase a USB controller license from planet-cnc.

    Click the link to respond:
    with the blueChick v4.2 can any software be used or doo we need to purchase a lic key from the manufacture of the control board for 75 bucks

  • I am interested in buying the greenBull 5X Long Z CNC Machine Kit, but it is not clear for me what is included in this kit. Is there anything else I need to get the machine work?

    The greenBull 4X comes with all of the components and electronics to assemble the gantry of the machine. You will need to build the table. We provide the rails and roller chain for the X-axis (along the length of the table for full 8 feet of travel). You will need to provide some wire to connect the electronics and a computer to run the machine. You will also need to purchase the software that you will need to run the machine that matches how you will apply the machine. We suggest the mach3 control program. The CAM program is up to you as there are many options out there.

    Click the link to respond:
    I am interested in buying the greenBull 5X Long Z CNC Machine Kit, but it is not clear for me what is included in this kit. Is there anything else I need to get the machine work?

  • Still working on GreenBull 5x10 assembly. Putting together the Z axis my motor mounts don't like the video, so I don't know which one goes where and in what orientation?
  • If I bring my 6090 with Huanyang VFD/spindle and G540 can you wire vfd/540 together and get it talking to mach3 for me?

    We can provide support to electronic components that we sell. We are unable to connect or diagnose electronics that we don't offer.

    Additional Information:
    We can provide solutions to products that we sell. For instance, we can inform how to connect a spindle's VFD to Mach3 using a RS-485 serial communication method.

    Click the link to respond:
    If I bring my 6090 with Huanyang VFD/spindle and G540 can you wire vfd/540 together and get it talking to mach3 for me?

  • I have a BlueChick that came with the 5-Axis Bread-Out Board V5 (parallel port), it has 3xCW230, how to configure it on LinuxCNC?

    Strictly to the point. Assuming:
    -You have a working linuxcnc install with a compatible parallel port
    -You have wired Bread-Out Board V5 to the motor drivers so you know which pins are for which signals(watch video tutorials for that on this site)
    -You have wired motors to motor drivers (watch video tutorials for that on this site)

    a)We need to know the base parallel port addres, for that you need to input on a linux terminal the command:

    #lspci -v

    You can scroll up and down the result with page up and page down. Look for a "Parallel Port..." line, the value you are looking for is the "I/O Ports at.." Write them down

    To get the Base Period Maximun Jitter, go to
    applications - cnc - Latency Test

    Now you should let that window running for a while, so it calculates an accurate jitter, go watch the tutorial videos for the connections between the Bread-Out Board and the motor controllers.

    After its been running for half an hour or so with the machine in use, write down the calculated jitter values, mine was Servo Thread - 39000

    Now close the Latency test dialog

    b)Go to applications - cnc - stepconfwizard
    "START" - Create a new config
    Check - Create Desktop Shortcut to config files
    Check - Create Desktop Shortcut to start linuxcnc with this config
    FORWARD

    c)"BASE INFORMATION"
    Fill in a Machine Name that suits you
    Bluechick is XYZ on inches
    Fill in the Base Period Maximun Jitter with the value obtained in "a)"

    FORWARD

    d)If you watched the tutorials on a) and b) you know the pin numbers for your signals.
    Parport Base Address you need to put the value obtained in a), mine was cf00
    Output pinout presets I used Sherline

    FORWARD
    FORWARD

    e)Axis X (chain and sprocket axis)
    Data for bluechick from build yourcnc
    Motor Steps per revolution 200
    Microstepping 64 (that if you followed tutorials, change if you have different)
    Pulley teeth 1 ; 1
    Leadscrew Pitch 0.444444 (that value comes from 1rev / (.25 in * 9 teeth))
    Maximun Velocity 10
    Maximun Acceleration 0.5
    Home location 0.0
    Table travel 0.0 to 34.0 (maybe you want to change this later)

    Now, you can do "Test this axis" and jog it (move it!) Try to position everything in the middle (you will be doing it axis by axis) and select
    "+ 0.5 in" Hit run, I used a pencil held at the gantry and paper to draw a line, then confirmed that the measurement was 0.5 in. Also tried with "+/- 0.5 in" and confirmed 1" measurement

    FORWARD when happy with your Axis X

    Repeat for Axix Y but the table travel is 0.0 to 12.0

    f)AXIS Z
    With data from buildyourcnc.com
    Motor Steps per rev 200
    Driver Microstepping 16 (as recommended for lead screw)
    Pulley teeth 1 ; 1
    Leadscrew Pitch 2
    Max Vel 2.5
    Max Accel 0.5

    Table travel 0.0 to 3.5

    Test, and FORWARD when happy

    g)After configured you can go to
    Applications - cnc - LinuxCNC, and there you go...




    Additional Information:
    ... Still think that there should be a tutorial for this part.

    Additional Information:
    oh¡ Forgot to tell, the config shortcut will be available on our Desktop, launch linuxCNC from there

    Click the link to respond:
    I have a BlueChick that came with the 5-Axis Bread-Out Board V5 (parallel port), it has 3xCW230, how to configure it on LinuxCNC?

  • DOES THE PLUG AND PLAY ELECTRONICS COMPUTER FOR 3 AXIS CNC MACHINE HAVE ENOUGH MEMORY RAM ADDITIONAL SOFTWARE (BOBCAD-CAM, BOBART, MACH3) TO BE ADDED FUNCTION WELL?

    The plug and play system does have enough memory for additional software. The redLeaf comes standard with a 1TB hard drive.

    Click the link to respond:
    DOES THE PLUG AND PLAY ELECTRONICS COMPUTER FOR 3 AXIS CNC MACHINE HAVE ENOUGH MEMORY RAM ADDITIONAL SOFTWARE (BOBCAD-CAM, BOBART, MACH3) TO BE ADDED FUNCTION WELL?

  • I have a greenbull 5x with the long Z. Is there a laser kit that I can get for that model?

    Yes, we can provide a laser attachment for the long Z version of the greenBull 4x, 5x and 6x. Please call us to get more information and pricing for the laser attachment.

    Click the link to respond:
    I have a greenbull 5x with the long Z. Is there a laser kit that I can get for that model?

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.