The blackTooth Laser cutter and Engraver can be built in a weekend. Take a look at the build instructions and try to determine if you feel you have sufficient capability to put together the laser system.

Click the link to add information to this solution:
HOW COMPLEX IS YOUR KIT TO ASSEMBLE, AND MOST IMPORTANTLY - HARD IT SETUP CONTROL THE LASER WITH MACH3?

The blackTooth Laser cutter and Engraver can be built in a weekend. Take a look at the build instructions and try to determine if you feel you have sufficient capability to put together the laser system.

Click the link to add information to this solution:
HOW DIFFICULT IS IT TO BUILD THE BLACKTOOTH LASER CUTTER?

You can find the wiring diagrams for the blackTooth on step 105 and 106 on the list of instructions on the blackTooth page. Step 105 pertains to the parallel breakout board and step 106 pertains to the USB interface board.

Additional Information:
wire size

Click the link to add information to this solution:
WHERE ARE THE WIRING DIAGRAMS FOR BLACKTOOTH LASER CUTTER IN INSTRUCTIONS?

Hour meter. This will tell you exactly how long your system has been 'on' giving you a more accurate bead on the length of your tubes life.

Click the link to add information to this solution:
WHAT CAN ADD TO MY BLACKTOOTH LASER CUTTER MEASURE THE TIME OF USE?

If you are located near Houston, Texas area you can stop by our shop. If you are not near us, you can check in our forums, and see if you can find someone in your area that has one of our machines, and would be willing to let you come see it in action.

Click the link to add information to this solution:
I WOULD LIKE TO KNOW IF THERE IS A STORE OR SHOP WHERE CAN SEE THE PRODUCT AND BUY IT?

Upgrade your mirrors to SI coated mirrors, using a HQ ZnSe lens and even pushing up to a beam expander will all boost power. The ideal order of experimenation for lowest cost would be changing out for a higher quality lens labeled HQ ZnSE lens. Next would be SI mirrors, which will absorb less heat and reflect better, the last would be to use a beam expander which expands the beam, reducing the heat signature on the mirrors and makes a tighter focal width.

Click the link to add information to this solution:
CAN BOOST THE POWER OF MY BLACKTOOTH LASER?

If you take the standard parallel cable BoB (Break Out Board), then you will need control software (Mach 3 or EMC2) and CAM software to make your G-Code (such as CamBam). Personally I use CamBam and Mach 3, they work beautifully but don't expect to turn them on and know how they work out of the box. Give yourself a few weeks to get familiar with the basics. CamBam is VERY powerful software for it's price. I'm surprised how much I keep learning on what I can do with it...I highly recommend it if you want as much control as possible.

Mach 3 + CamBam as a bundle costs $310. EMC2 will give you a free replacement for Mach 3 and is exclusively for Linux.

If you use the USB BoB, it will cost an extra $75 + $75 for the software. This is an all-in-one package so no need for Mach 3 or CamBam.

For etching rasters (jpeg, bmp, tiff, non-vectors, photos), I highly recommend PicEngrave. It has been a labor of love for the past 9 years and John has done a wonderful job with it. It easily compares in quality compared to software that is in the $200-$300 range. John's software runs $40 and can be found here: http://picengrave.com/ (don't let the modest website fool you, this stuff can do amazing things). DotG and the Mach3 engrave plugin are two other options and instructions can be found on Dustans page in the gallery on buildyourcnc.com website.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
WHAT SOFTWARE CAN BE USED WITH THE BLACKTOOTH LASER CUTTER?

Cooling is not as tricky as you might think. There is 3 ways to approach this, only 2 really matter for a low scale 40w setup. First one is the cheapest and easiest. The higher the temp of water the worse your performance will be, from what I understand anything in the 30C range is about the most tolerable it gets. Lower is better. But not frozen...from what I've been told a very experienced cutter, he found 8C was the highest power he achieved.

1. Use a 5 Gallon resovoir system which gives you a fairly large space of water to heat up before you need to tend to it. Add about a cup of anti-freeze to the mix of DISTILLED water. You don't want ANY minerals in the water that might build up in your system. The anti-freeze works to keep algae and other ickies from growing in your water.

2. Use a smaller resovoir system (or even closed loop) and install 1 or more radiators found in CPU cooling systems with 120mm fans attached. This will continously cool your water system to ambient room temperatures, but with a tiny resovoir it will be difficult to add things like ice-packs to drop the temps if the ambient is quite hot.

3. Using an industrial coolant system. Overkill and unless your cutting A LOT, this is a very expensive option to take. You can also explore the idea of Peltier cooling but it is extremely expensive electricity/BTU wise compared to an industrial cooler.

Click the link to add information to this solution:
HOW TO COOL THE BLACKTOOTH 40W LASER TUBE

Locate the switch as close to where you will normally be as possible and in clear sight.

Click the link to add information to this solution:
WHERE IS GOOD PLACE TO PUT THE E-STOP SWITCH?

Check step 9 on this page: http://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Click the link to add information to this solution:
IF YOU HAVE CIRCUIT (OR PICTURE) OF HOW THIS RELAY IS CONNECTED TO THE ROUTER

Temperature probe monitor. Very valuable. This keeps you up to date on your coolant temperature levels.

Voltage meter. This will tell you the exact level of voltage/power you are running telling the laser to run at instead of an arbitrary mark on a drawn wheel around your POT.

Ammeter sensitive to 1mA. This will be sure your not over driving your tube and reducing it's life significantly.

Hour meter. This will tell you exactly how long your system has been 'on' giving you a more accurate bead on the length of your tubes life.

Exhaust fan upgrade. The current fan included is 100CFM. You can buy 120mm fans that push 250CFM and I have included a guide on how to go about doing this here. http://buildyourtools.com/phpBB3/viewto ... 8cdd1802bf

To push the exhaust fan even further, if you have the room/power, I would highly recommend investing in a 600+ CFM "Dust Collector" system. 250CFM is still not suffice to draw all the smoke that can come off of 3mm or 1/8 MDF cutting job.

A cutting surface. I bought myself a aluminum 'egg crate' mesh from my local HVAC company. They are used a cover for fluorescent lights and work great for low impact cutting surface. They come in 4'x8' sheets and are easily cut to fit. The other side is if you can find a steel honeycomb cutting bed to fit. These can be quite costly or fairly affordable depending where you are looking. The benefit of a steel honeycomb is you can use high power magnets to hold material down.

Click the link to add information to this solution:
WHAT ARE SOME USEFUL MODIFICATIONS CAN APPLY TO THE BLACKTOOTH LASER CUTTER?

If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

Additional Information:
ur gay

Additional Information:

Click the link to add information to this solution:
MY COMPUTER DOES NOT HAVE A PARALLEL PORT. HOW DO I INTERFACE WITH THE MACHINE?

Peak influenza activity does not generally occur until February. Providers are encouraged to continue vaccinating patients throughout the influenza season, including into the spring months (e.g., through May), as long as they have vaccine in the refrigerator and unvaccinated patients in their office.

Because influenza occurs in many areas of the world during April through September, vaccine should be given to travelers who missed vaccination in the preceding fall and winter. Another late season use of vaccine is for children younger than age 9 years who were vaccinated for the first time in the current vaccination season but failed to get their second dose. For each of these situations, vaccine can be given through the month of June since injectable influenza vaccine customarily has a June 30 expiration date.

Click the link to add information to this solution:
HOW LATE IN THE SEASON CAN I VACCINATE MY PATIENTS WITH INFLUENZA VACCINE?

Same issue here -- TTL output from the AWC708C never seems to be pulled low. Still troubleshooting.

Click the link to add information to this solution:
MY LASER MACHINE VERTICAL DOES NOT ACTIVATE THE LASER TUBE, VERIFY THE POWER SUPPLIES AND THEY ARE WORKING WHICH THE PROBLEM CAN BE

If you select the Settings Page and select or tick Auto Limit Override - this will allow you to back off the switch.

Additional Information:
limit and home switch

Click the link to add information to this solution:
IS THERE A WAY TO GET RID OF THE PARALLEL CABLE AND SOMEHOW USE USB ?

You can test the power supply, but you will need to take extra special care since the voltage on the high tension line can be lethal. Go to this instructable to see all the step on testing the power supply:

http://www.instructables.com/id/How-to-test-and-set-a-Chinese-China-made-CO2-Laser/?ALLSTEPS

Additional Information:

Click the link to add information to this solution:
I am building the Blacktooth laser cutter. What is the safest and most accurate way to test the output of the laser power supply WITHOUT connecting the laser tube? Can I use a standard multimeter and measure the voltage output of the laser power supply?

If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

Additional Information:
ur gay

Additional Information:

Click the link to add information to this solution:
MY COMPUTER DOES NOT HAVE A PARALLEL PORT. HOW DO I INTERFACE WITH THE BREAKOUT BOARD?

Depth of Field. This is how far the focal point goes before re-expanding again. With a 2" lens, you have approximately 2-3mm of DOF. This means that you'll have 2-3mm of perfectly focused laser before it starts to re-expand again. If you have a 4" lens, you will have up to 7mm of DOF.

Additional Information:

Click the link to add information to this solution:
WHAT IS D.O.F OR DEPTH OF FIELD FOR THE BLACKTOOTH LASER AND LENS?

Yes, it is ok if the thickness is plus or minus +/- about 2mm.

Additional Information:



Additional Information:

Click the link to add information to this solution:
is IT OK TO USE THICKER PLYWOOD (MATERIAL) to BUILD THE CNC MACHINE, BLACKFOOT, BLACKTOE?