Depending if the spindle can work with this specific VFD, it might be possible. However we would not like to risk you working unit, with a possible match so we would like more details on your specific model and any information available on the spindle itself.

Response
The only info on the spindle is 2.2KW 400HZ 220V. Made by Zhong Hua Jiang.

Was originally on a Delta C200 vfd. That is 220 single phase.

Click the link to add information to this solution:
I PURCHASED A VFD AND SPINDLE FROM FRIEND, HIS SET UP IS 220. DON'T HAVE 220 IN MY SHOP. QUESTION CAN USE YOUR 110 WITH THIS SPINDLE??

Our spindles are 2 pole, however we do not understand the "and pairs" portion of your question?

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
How many poles and pairs does your 2.5 KW spindle have?

That will depend on the controller that was installed in the redFly. If the controller is a pokeys57CNC controller, you can use Mach 4 with that system.

You can add a 4th axis and an ATC (Automatic Tool Changer) with the redFly system.

Click the link to add information to this solution:
Does the Redfly that I bought with the GreenBull in 2016 work with Mach4? Also I want to add a 4th axis and a spindle with automatic tool changer. Will this work too or do I need a new control board? I bought my CNC with a longer Z travel, so I have plenty of room for these. Thanks!

The VFD does come with a manual that details the wiring and connection specifications, terminal features and a list of the parameters. There is no information on how to connect it to Mach3. It does detail the specifications within the parameters and terminal features on the analog input that is used with Mach3 and other control programs.

Click the link to add information to this solution:
I have a water cooled spindle I only need the VFD drive. Does the VFD come with instrutction on hooking the VFD to Mach3?

To control a spindle using the USB CNC interface, you will need a relay board that contains a transistor that can activate the relay with a power source with enough current that can activate the relay. This video explains all of the information you will need to develop this relay circuit:

Click the link to add information to this solution:
i have a breakout usb controller iam using a spindle output to active a relay 5V but it didnt work.... whats the problem, what else i need to active that realy 5v 10A?

At this time we are working to release a new USB controller board that will be compatible with Mach4 software and do not have any immediate plans to update the Planet-CNC USB board.

Click the link to add information to this solution:
Are there plans to release a USB Controller to work with the Planet CNC Output Board for more advanced spindle control from within Planet CNC?

I have not tried connecting a 110V spindle to a 220V VFD; however, the parameters in a 220V VFD do allow changes to the values for the spindle motor. If you do plan on connecting the 110V spindle to a 220V VFD, damages can occur, so I would not recommend it.

With that said, here is the output of an LLM:
Using a 220-volt VFD (Variable Frequency Drive) to run a 110-volt spindle is technically possible, but it requires careful setup to avoid damaging the spindle. Here's what you need to consider:

Check the VFD Specifications: Ensure that the VFD can be set up to output the correct voltage for your spindle. Many VFDs are capable of outputting variable voltages and can be configured via their programming settings to match the voltage requirements of the spindle.

Adjust the Output Voltage: You'll need to configure the VFD to output 110 volts to match your spindle. This is crucial because supplying 220 volts to a 110-volt spindle would likely damage it permanently. Check the VFD's manual for instructions on how to adjust the output voltage settings.

Set the Current Correctly: Besides voltage, make sure the output current does not exceed what your spindle can handle. The VFD should be configured to supply the current at the rating appropriate for the spindle’s power and voltage requirements.

Consult the Manuals: Always refer to the manuals of both the spindle and the VFD. These documents can provide specific guidance on compatibility and settings.

Consider Professional Installation: If you are not familiar with electrical systems or if the manuals do not provide clear guidance, it may be wise to hire a professional. This helps ensure that the setup is done safely and correctly.

By taking these steps, you can safely use a 220-volt VFD with your 110-volt spindle, ensuring it operates efficiently without risk of damage. Just be meticulous with the settings and when in doubt, consult with or hire a professional.

Click the link to add information to this solution:
[77] I have a 110 volt 2.2kw water cooled spindle. Can I run it with a 220 volt VFD?

Identify the Control Signals: First, determine which control signals from the DB25 interface card are used for spindle speed control. Typically, these are PWM (Pulse Width Modulation) signals or analog voltage signals.

VFD Configuration: Your VFD should be configured to accept the type of control signal your DB25 card provides. This involves setting parameters in the VFD that correspond to the type of input signal it will receive for speed control.

Wiring: Connect the appropriate output pins from the DB25 card to the input terminals on the VFD. This usually involves connecting the PWM or analog output to the corresponding input on the VFD. Make sure to consult the manuals for both your VFD and interface card for specific wiring details.

UCCNC Settings: Configure UCCNC to output the correct type of signal (PWM or analog) that matches your VFD's configuration. This is done through the software's spindle setup section.

Test and Adjust: Run some tests to ensure that the spindle speed is being correctly controlled by UCCNC. You might need to tweak settings in either the VFD or UCCNC for optimal performance.

Click the link to add information to this solution:
I am looking at purchasing your 2.2 kw water cooled spindle. I'm assuming it comes with the VFD. I have a rotary phase converter in my shop. Are these spindles 3 phase? And if so, can I bypass use of the VFD and control the spindle speed by the CAM software instead? Or is the VFD an absolute necessity to use on the spindle?

Identify the Control Signals: First, determine which control signals from the DB25 interface card are used for spindle speed control. Typically, these are PWM (Pulse Width Modulation) signals or analog voltage signals.

VFD Configuration: Your VFD should be configured to accept the type of control signal your DB25 card provides. This involves setting parameters in the VFD that correspond to the type of input signal it will receive for speed control.

Wiring: Connect the appropriate output pins from the DB25 card to the input terminals on the VFD. This usually involves connecting the PWM or analog output to the corresponding input on the VFD. Make sure to consult the manuals for both your VFD and interface card for specific wiring details.

UCCNC Settings: Configure UCCNC to output the correct type of signal (PWM or analog) that matches your VFD's configuration. This is done through the software's spindle setup section.

Test and Adjust: Run some tests to ensure that the spindle speed is being correctly controlled by UCCNC. You might need to tweak settings in either the VFD or UCCNC for optimal performance.

Click the link to add information to this solution:
HEY ! I HAVE PURCHASED A VFD WITH MATCHING SPINDLE 1.5KW AND CONTROL PROGRAM UCCNC. MY INTERFACE CARD IS DB25, THE QUESTION HOW DO CONNECT TO DB25 SO THAT CAN SPEED UCCNC? SINCERELY "CNC BEGINNERS"

Can you provide the model number of your VFD?

Yes, I have the "YL600 - 2S - 2K20"

It just came with a small booklet that is all in Chinese...

Click the link to add information to this solution:
I WIRED MY VFD (2.2KW VERSION) AND TRIED TEST RUNNING THE SPINDLE. CONFIGURED TO YOUR SPECS ON THIS WEBSITE, ONLY ISSUE IS WE GOT AN ERROR CODE. ERR 02, DO YOU KNOW WHAT IS? OR HAVE A LIST OF CODES? THANK

You will definitely want to adjust your debounce setting in mach3 if your emergency or limit switch is engaging.

Additional Information:
Did you ever fix this issue? I am having the same problem.

Additional Information:
Did you ever fix this issue? I am having the same problem.

Additional Information:
Did you ever fix this issue? I am having the same problem.

Additional Information:
Did you ever fix this issue? I am having the same problem.

Additional Information:
Did you ever fix this issue? I am having the same problem.

Additional Information:
Did you ever fix this issue? I am having the same problem.

Additional Information:
Did you ever fix this issue? I am having the same problem.

Additional Information:
Did you ever fix this issue? I am having the same problem.

Additional Information:
Did you try changing the denounce setting?

Additional Information:
Meant to say denounce.

Click the link to add information to this solution:
When I start my spindle I get a emergency stop in Mach 3. I have run shielded cable and it is grounded at the VFD it is wired per you site instructions. any idea what to check

The leadscrew length for the greenBull long Z-axis is 47 inches.

Additional Information:

Click the link to add information to this solution:
BUILDING ONE OF YOUR GREENBULL 6X LONG AND 2.2 KILOWATT SPINDLE DOES NOT FIT. SEEMS LEAD SCREW YOU SENT WITH KIT IS SHORT 42" LOOKS LIKE IT NEEDS TO BE 5 OR 6 INCH LONGER. THIS CORRECT? WHAT THE NEEDED LENGTH FOR UNIT?

Yes, all of the spindles come with collets. The collets have a 1/4" (6.35mm) bore for end mills that have a 1/4" shank. The ER specification is different for the 1.5kW (ER-11) and the 2.2kW (ER-20).

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I’M LOOKING TO PURCHASE SPINDLE AND VFD WAS CURIOS IF THE SPINDLES COME WITH COLLETS SO WHICH ONES?

There is a button on the front of the VFD that will cycle through RPM, Freq, and a few other readings. If there is a >> button on your VFD, that will work. If there is a mode button on your VFD, that should works as well.

Additional Information:
There is a >> disc button but it does not cycle through the display modes.

Additional Information:
Is there a parameter setting to make this button work to cycle thru the display modes?

Additional Information:
setting the starting rpm

Additional Information:
the vfd will not start the motor

Additional Information:
Any progress on this? I have the same issue.

Additional Information:
What model is your VFD?

Additional Information:
Mine is a YL620-G-5.5Kw

Additional Information:
That model will not be able to show RPM. You will be able to show the frequency, which can be used to determine the RPM. RPM equals the Frequency x 60.

Additional Information:
There is an Icon for RPM at the top of the display I cannot cycle through the different options to see the RPM

Additional Information:
At the top of my control panel is has 6 different lights which indicate what your seeing. in order from left to right they are COM, ALM, DISP, RUN, Hz, RPM I have seen the ALM light up on initial set up but that was fixes with a parameter change. The run light shows up when i turn the spindle on and and it is running. I am however not able to get any of the other lights to show or to get the RPMs to display

Additional Information:
If you do see an RPM light on the display, that panel sticker may be a sticker used for many types of VFDs and the RPM is not used. There is parameter: P00.24 which allows you to pick what to display. The choices a
re:
0: Display current target frequency. This will display your knobs, potentiometer, setting, not the actual spindle frequency.
1: Display electric machinery run frequency. This will display the actual frequency that the VFD is currently sending to the spindle.
2: Display electric machinery run current: this will display the current the spindle is currently drawing.
3: Display input AC voltage. Self explanatory.
4: Display mother line voltage. This will display the actual voltage at the input.
5: Display output voltage. This will display the voltage at the UVW terminals for the spindle.
6: Display speed paragraph number SPx. I believe this displays which frequency is being selected (P07.00 to P07.07, or 1 to 8 respectively).
7: Display inverter temperature. This is the temp of the VFD, self explanatory.
8: Display input signal X1-X3/output signal. This simply shows the inputs/outputs associated with the external terminals.
9: Display user variable. This one I have not delved into, so it may be something to look into.
10: Display user count value. Same, this one could be useful.
11: Display temporary debugging variable. Haven't tried this one, so I can't inform of any useful information but it won't pertain to this subject anyway.
12: Display automatic multisegment run step and time. I haven't delved into this one either, but it won't show RPM.

Click the link to add information to this solution:
How to display RPM instead of frequency on the VFD? I have the 2.2kv 110 volt spindle and inverter.

The laser tube is a consumable item in all CO2 lasers, unless the laser tube can be recharged. My laser tubes will most likely work as long as the mouts are the same size. Let me know the mount diameter and the length of space for the tube in the Epilog Laser Cutter and Engraver and I will let you know.

Additional Information:
My Epilog Summit (3.3) only works from Windows Millenium and 98. Notconsistently from WXP, but sporadic raster and vector combined does happen. I can't get it to work right w XP through Harvard Draw, Corel,Image Folio, Stika, DrawMagic or anything else I have. But Millenium isOK except for the advanced mapping to colors function is very difficult.When it does rarely accept a graphic from my XP system from CorelDrawEssentials or 8.0, it will allow complete control for photo etching -speed, power and shade mapping. It is the same driver for both mysystems but the control panel page looks different in the 2 computers. The laser takes 45 seconds to initialize after power on. You can use a USB to Parallel adapter cable for your laptop or modern computer connection. The laser needs the old style printer connection. Test your laser by holding all 3 power/focus/speed buttons until homed. Close the lid. "Online" for lase, any other button for laser off. Should be an audible beep every few seconds while your laser is functioning. This is not a motion test -only laser firing.

Click the link to add information to this solution:
I have a 25 watt Epilog Summit Model 2000/25 laser engraver. I believe my tube is going bad due to limited vector cutting and no raster. Do you think there is a way to retrofit with your products to make it work well. Mirrors are new and mechanical is good. Thanks.

Identify the Control Signals: First, determine which control signals from the DB25 interface card are used for spindle speed control. Typically, these are PWM (Pulse Width Modulation) signals or analog voltage signals.

VFD Configuration: Your VFD should be configured to accept the type of control signal your DB25 card provides. This involves setting parameters in the VFD that correspond to the type of input signal it will receive for speed control.

Wiring: Connect the appropriate output pins from the DB25 card to the input terminals on the VFD. This usually involves connecting the PWM or analog output to the corresponding input on the VFD. Make sure to consult the manuals for both your VFD and interface card for specific wiring details.

UCCNC Settings: Configure UCCNC to output the correct type of signal (PWM or analog) that matches your VFD's configuration. This is done through the software's spindle setup section.

Test and Adjust: Run some tests to ensure that the spindle speed is being correctly controlled by UCCNC. You might need to tweak settings in either the VFD or UCCNC for optimal performance.

Click the link to add information to this solution:
Hey ! I have purchased a VFD with matching spindle 1.5kW and control program UCCNC. And my interface card is DB25, the question is how do I connect the VFD to DB25 so that I can control the speed with UCCNC? Sincerely "cnc beginners"

Yes, our porter cable collets and nuts will fit the porter cable 7518.

Additional Information:

Click the link to add information to this solution:
HAVE PORTER CABLE 7518 ROUTER ON MY CNC AND WOULD LIKE TO KNOW IF YOUR ER20 COLLET NUT, FOR THE CABLE, WILL FIT ROUTER.

The 2.2kW spindle will have the same amount of torque and strength using either the 110V or the 220V inverter. Nothing will significantly change in either application since the 110V inverter has a small step up transformer which will increase the voltage from 110V to 220V to run the spindle efficiently.

Additional Information:
I'd like confirmation on this -- isn't there a cost in efficiency to having the 110v step up to 220v?

Additional Information:
Thank you so very much for explaining this!!! I truly appreciate your help! Tricia

Additional Information:
Thank you so very much for explaining this!!! I truly appreciate your help! Tricia

Additional Information:
Thank you so very much for explaining this!!! I truly appreciate your help! Tricia

Additional Information:
Thank you so very much for explaining this!!! I truly appreciate your help! Tricia

Additional Information:
Thank you so very much for explaining this!!! I truly appreciate your help! Tricia

Click the link to add information to this solution:
Good morning, I would like to know if the strength of the 2.2kw spindle is weaker when using the 110V version of the VFD. Does it have the same power as the 220V version VFD?

Spindles are generally covered up to 1 year after date of purchase. We do not repair them in house, but we do work with our manufacturer to replace defective units. Generally if you have a defective unit covered under warranty, we will issue a replacement.

Click the link to add information to this solution:
what is the warranty period and do you repair these in house? 2.2 kW (kilowatt) Water Cooled Spindle with Inverter (VFD)