The NENA 14 motor is paired with this driver and will work very well: https://buildyourcnc.com/item/motion%20electronics-steppermotordriver-newbiehack-Motor_Drivers-2!5_Amp_modular

Click the link to add information to this solution:
I cannot find a driver for the NEMA 14 Stepping Motor (17 oz-in 1/4" dual shaft) on your site, would something like the Pololu DRV8834 be okay? (I note that the stepper requires 2.7v)

We don't offer those drive pullies with a 3/4" bore at the moment. We can supply them if you are willing to wait. If so, what is the pulley pitch, how many teeth and the width of the belt.

Additional Information:
Meant to say pulleys, not pullies.

Click the link to add information to this solution:
Do you offer or can recommend a place where I can buy the Drive Pulley for NEMA 43 Stepper Motor (1586 oz-in 3/4" single shaft) 5.5 Amps?

The NEMA 11 16.7 oz-in motor is a dual shaft motor and the rear shaft extend 15mm or .59 inches.

I've added an image to the product page:
https://www.buildyourcnc.com/item/electronicsAndMotors-nema11-16!7ozin-NEWBIEHACK-motors-stepping_motor-16!7_ozin

Click the link to add information to this solution:
Is the NEMA 11 Stepper Motor (16.7 oz-in .185" dual shaft) 0.67 Amps actually a dual shaft stepper motor? The drawings only show the shaft coming out one side.

You can find the wiring diagram, and technical specifications for the NEMA 23 motor, on it's product page, found here,

https://www.buildyourcnc.com/Item/electronicsAndMotors-nema23-100ozin-newbiehack-motors-stepping_motors-100_ozin

There is a datasheet below the product description. This image will expand to be easier visible once clicked on.

Click the link to add information to this solution:
What is the number of pole pairs and rotor inertia for NEMA 23 Stepping motor?

Yes, we have the NEMA 11 16.7 oz-in stepper motor with dual shaft in stock.

Click the link to add information to this solution:
Do you have it in stock? (NEMA 11 Stepper Motor (16.7 oz-in .185" dual shaft) 0.67 Amps)

Yes, we honor a one year warranty on the NEMA 34 651 oz-in stepper motor.

Click the link to add information to this solution:
Is there a warranty on the NEMA 34 651 Oz-in stepper motors you sell?

The torque curve for the 651 oz-in stepping motor can be found here:

https://www.buildyourcnc.com/item/electronicsAndMotors-nema34-651ozin#prettyPhoto

Click the link to add information to this solution:
Using your NEMA 24 stepping motor with microstepping, can I get a speed range from 3 RPM to 600 RPM ?

Please measure the resistance between all the wires in all combinations to determine where these wires exists with the coils. I am not familiar with 5 wire stepper motors.

Click the link to add information to this solution:
Can this driver accept 5 lead Nema 34 steppers: Stepping Motor Driver (24-70 volts DC, up to 6.0 amps, microstepping from 1/2 to 1/256)

There are a number of opportunistic gadgets on the market to allegedly protect the user from hazards of cellular phones. You can search the Internet to find the latest, ranging from antenna shields to whole-body shielding materials. Most experts believe that these devices take advantage of customers' misunderstanding and unfounded fears to sell products with no real value. First of all, cell phones that operate within the guidelines established by national and international safety panels have never been shown to pose a health risk to the user (see answers to other questions on cell phone safety on this website). Secondly, placing any kind of shield over the antenna of a cell phone will in most cases cause it to increase its RF output as it attempts to compensate for signal loss in the shield and maintain a quality phone call. The U.S. Food and Drug Administration published an advisory on cell phones several years ago that said if you are concerned about risks of using a cell phone, then simply use it less. That is still good advice today. Gary Zeman, ScD, CHP Lawrence Berkeley National Laboratory

Additional Information:



Additional Information:

Click the link to add information to this solution:
ARE THERE PRODUCTS AVAILABLE TO THE GENERAL PUBLIC THAT CAN BE PURCHASED PROTECT CELLULAR OR PORTABLE TELEPHONE USERS FROM RADIATION? IF SO, WHERE THESE FOUND?

The 651 oz/in NEMA 34 stepper motor does have a dual shaft. The shaft extends 19 mm at both ends.

Click the link to add information to this solution:
3 axis heavy gantry combo. Is the Nema 34 motor dual shaft?

I haven't delved into using encoders with stepping motors too much. From my research, you need to have a controller that can provide the closed loop control, rather than software handling that process. I have also found from my research that using encoders on stepping motors is generally used to stop the machine in the case that the motor failed to achieve the commanded position for some reason and gives the user the chance to correct and continue with the job.

If you want proper closed loop control, it may be best to go with servos and servo controller that provide the closed loop control within the real of those two components.

Click the link to add information to this solution:
I HAVE NOT SEEN ANY REFERENCES TO STEPPING MOTOR ENCODER FEED-BACK FOR CLOSED LOOP CAPABILITY IN OF THE HARDWARE YOU SELL. THIS A SUPPORTED FEATURE WITH HARDWARE/SOFTWARE SELL?

Currently we do not have that modification kit, our set up is fixed for our greenBull only modification kit we have for this model is the long z-axis kit(Designed for Foam cutting).

Click the link to add information to this solution:
I am building your "Green Bull' 6 foot wide kit and I am at the stage of attaching the motor and drive chain. I would like to know if you have an modification kit available to put the 1/2" ACME screw on the Y-axis?

For the NEMA 34 stepper motor with a maximum current of 6 amps, 18 AWG wire would technically be sufficient. According to the American Wire Gauge (AWG) standard, 18 AWG wire can handle up to around 10 amps of current in chassis wiring and around 16 amps in power transmission. If you are considering running a very long length of cable from the driver to the stepper motor, you may want to consider using 16 AWG.

As for the spindle, this wire gauge is well-suited. There are three phase shifts, each at 120 degrees and each conductor is carrying only 1/3 of the power. At 220v, 2200 watts / 220 V = 10 amps. 1/3 of 10 amps is 3.333 amps, so each conductor will be have a load of 3.33 amps.

Click the link to add information to this solution:
[801] Is this enough rating for a Nema 34 motor with max 6 amps? Also what about a 220V 2200Watt Spindle?

We attempt to provide as many services as possible to fit the needs of the CNC community. For a quote on a custom job, please email customerservice@buildyourcnc.com and we will be happy to assist you.

Click the link to add information to this solution:
I bought longs motor nema 34 stepper motor with 4 powers supply and dm860 from ebay, would you be interested in doing all the wiring for me? I pay you for you time

The settings that will have to be change will be your steps per inch in motor tuning (mach 3), or settings/axes(planetCNC). But we do not have the actual numbers/specs that will fit your 10 TPI 5 start lead screw, here is a tutorial video which explains how to get the exact numbers you need! (

Click the link to add information to this solution:
I just changed my X and Y to the ACME 1/2" 5 start lead screw. What are the motor tuning numbers. I have the book built machine.

We don't have cad models of the HIWIN blocks, but you can find the models on McMaster.com. They have can drawings and models for most of these types of parts.

Click the link to add information to this solution:
DO YOU HAVE CAD AVAILABLE FOR THE HIWIN GUIDE BLOCKS SELL AND RAIL?

We don't have cad models of the HIWIN blocks, but you can find the models on McMaster.com. They have can drawings and models for most of these types of parts.

Click the link to add information to this solution:
DO YOU HAVE CAD AVAILABLE FOR THE HIWIN GUIDE BLOCKS SELL AND RAIL?

The most important factor in preventing outbreaks is annual vaccination of all occupants of the facility, and all persons in the facility who share the same air as the high-risk occupants. Groups that should be targeted include physicians, nurses, and other personnel in hospitals and outpatient settings who have contact with high-risk patients in all age groups, and providers of home care to high-risk persons (e.g., visiting nurses, volunteers).

Click the link to add information to this solution:
ARE THERE RECOMMENDATIONS FOR THE PREVENTION OF INSTITUTIONAL OUTBREAKS INFLUENZA?

The frame size difference of the NEMA 23 and 24 is very slight and, depending on the motor mount both will most likely fit. The bigger difference between these stepping motors is the torque. Make sure that the motor that you purchase has the appropriate torque for the axis that it will move.

Is is safe to go with the higher torque? Or if the torque is too high for what i need is that bad?

You can use a motor with higher torque. Just make sure to select the correct driver for that motor.

Additional Information:
The frame size has nothing to do with torque. Nema 23 means a 2.3" frame. Nema 24 means a 2.4" frame. That's all. Either could have more or less torque depending on speed and power.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
What is the difference between a NEMA 23 and NEMA 24 motor? can I use either one on a machine?