The overall size of the machine, really depends on both the area available to you and also the overall size of material being used. Now our larger machines (blackFoot, greenBull, greenLean) can cut all the materials mentioned above, and if equipped with our 2.2kW spindle you will be accurate up to ten thousandths of an inch.
Our greenBull machine does have an option for a long-z axis, that was especially designed to cut foam, but depending on the overall size it might not be a requirement for the specified request.

Click the link to add information to this solution:
I HAVE A SIGN SHOP AND WE NEED CUT ALUMINUM, PLEXIGASS, FOAM AND OTHER MATERIALS FOR SIGNS. CAN YOU TELL ME WHAT MACHINE WE NEED? I LOOKING 4'X8' OR 5' X 10'

I haven't delved into using encoders with stepping motors too much. From my research, you need to have a controller that can provide the closed loop control, rather than software handling that process. I have also found from my research that using encoders on stepping motors is generally used to stop the machine in the case that the motor failed to achieve the commanded position for some reason and gives the user the chance to correct and continue with the job.

If you want proper closed loop control, it may be best to go with servos and servo controller that provide the closed loop control within the real of those two components.

Click the link to add information to this solution:
I HAVE NOT SEEN ANY REFERENCES TO STEPPING MOTOR ENCODER FEED-BACK FOR CLOSED LOOP CAPABILITY IN OF THE HARDWARE YOU SELL. THIS A SUPPORTED FEATURE WITH HARDWARE/SOFTWARE SELL?

The maximum length we can ship is a total of 78" inches. However we can send your required length in portions. Please refer to adding the total items you require to your cart to get a visualized amount and shipping cost.

Click the link to add information to this solution:
Regarding 1/2" 5 start and 10 TPI ACME precision lead screw, what the maximum length you can ship within USA? I'm looking for something like 100" and I could use a 1" screw if available. Please include estimated price. Thanks.

Please contact us at sales@buildyourcnc.com so we can provide you with assistance on your order

Click the link to add information to this solution:
I am trying to purchase a kit for our school in Singapore, and your site keeps refusing our corporate AMEX card. Can you help us figure out what is up with that? Are you not ship to Singapore or something? Our AMEX rep says that the account is authorised for this purchase from our end, so the problem may be with your site? Please advise.

BYCNC Response:
This is correct. You will need to use a method appropriate for the software you are using. Also remember that NC switches are typically wired in series, while NO switches are normally wired in parallel.

User Response:
I am using the cnc planet software for your USB board. Are the limit configurations in this software?

BYCNC Response:
Yes, Planet CNC software is compatible with the use of limit switches. Configuration information will depend on your specific application. You can view Planet CNC's information here: http://www.planet-cnc.com/files/CNCUSBController.pdf

Click the link to add information to this solution:
LIMIT SWITCHES FOR AXIS. THE PRINT SHOWS THAT YOU CAN WIRE LIMITS EITHER N.O. OR N.C. SO IF THIS IS CORRECT I WOULD NEED TO TELL BOARD IN SOFTWARE HOW LOOK AT THESE LIMITS, I'M GOING GET AN INPUT LOOSE DEPEND ON IT.

The leadscrew length for the greenBull long Z-axis is 47 inches.

Additional Information:

Click the link to add information to this solution:
BUILDING ONE OF YOUR GREENBULL 6X LONG AND 2.2 KILOWATT SPINDLE DOES NOT FIT. SEEMS LEAD SCREW YOU SENT WITH KIT IS SHORT 42" LOOKS LIKE IT NEEDS TO BE 5 OR 6 INCH LONGER. THIS CORRECT? WHAT THE NEEDED LENGTH FOR UNIT?

I haven't delved into using encoders with stepping motors too much. From my research, you need to have a controller that can provide the closed loop control, rather than software handling that process. I have also found from my research that using encoders on stepping motors is generally used to stop the machine in the case that the motor failed to achieve the commanded position for some reason and gives the user the chance to correct and continue with the job.

If you want proper closed loop control, it may be best to go with servos and servo controller that provide the closed loop control within the real of those two components.

Click the link to add information to this solution:
I HAVE NOT SEEN ANY REFERENCES TO ENCODER FEED-BACK CAPABILITY IN OF THE HARDWARE YOU SELL. THIS A SUPPORTED FEATURE WITH HARDWARE/SOFTWARE SELL?

We sell our ACME screws in total length (overall length you require), but if individual lengths are needed you can contact us via phone (281-815-7701) or email (customerservice@buildyourcnc.com).

A $2.00 order will be a total of 1 inch, but if ordered separately then you will receive 2 of the same length.

Click the link to add information to this solution:
For the 1/2'' 5 start ACME leadscrew, what is the length purchased for the $2.00 order? and if you make 2 orders, are you getting two separate rods or 1 rod at twice the length. Thanks.

Can you provide the model number of your VFD?

Yes, I have the "YL600 - 2S - 2K20"

It just came with a small booklet that is all in Chinese...

Click the link to add information to this solution:
I WIRED MY VFD (2.2KW VERSION) AND TRIED TEST RUNNING THE SPINDLE. CONFIGURED TO YOUR SPECS ON THIS WEBSITE, ONLY ISSUE IS WE GOT AN ERROR CODE. ERR 02, DO YOU KNOW WHAT IS? OR HAVE A LIST OF CODES? THANK

Prior to the 2010-11 vaccination season, only children ages 6 months through 18 years and adults age 50 years and older were universally recommended for vaccination; recommendations for adults ages 19 through 49 years were targeted to people with specific risk factors, although other adults could be vaccinated if they wanted protection. Collectively, these targeted risk groups made up 85% of the U.S. population. During the 2009 H1N1 outbreak, additional risk groups were identified, such as obese individuals. The recommendation made by ACIP in February 2010 for universal vaccination simplifies previous recommendations, making it easier for healthcare providers to determine whom to vaccinate. The universal recommendation also makes it easier for patients to remember to get vaccinated every year.

Click the link to add information to this solution:
WE'RE GLAD THAT CDC HAS MADE A UNIVERSAL INFLUENZA VACCINATION RECOMMENDATION TO VACCINATE EVERYONE 6 MONTHS AND OLDER. WOULD YOU TELL US HOW THIS CAME ABOUT?

Our MAch3 USB interface boards can be located here:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
I AM INTERESTED IN THE 3 AXIS COMBO USB OPTION. NOTICE YOU ENDORSE PLANET-CNC FOR USE WITH THIS BUT WILL MACH3 INTERFACE WELL BEAK OUT BOARD?

Our CNC machines can be lengthened to work with our customers specific projects.

For a 3.5' x 14' cutting surface, I would recommend our greenBull 4X! (4'x8'). You will only need to add the remaining length of rail(4) and chain(2) to accommodate the additional 6Ft, so this machine will have a cutting surface of 4' x 14'.

The additional lengths for the x-axis travel will be a total of 28Ft, and 14Ft of chain. We recommend selecting all the items you wish to purchase and see the actual total in your cart.

Click the link to add information to this solution:
I HAVE INTEREST IN SOME KIT AROUND 14' X 3.5' CAN YOU SUPPLY? ALREADY PRICE? AND WHAT MORE NEED?, MY IS MODELING KAYAKS CNC

This will depend on the VFD you have to identify the correct terminal. The terminal on the VFD will be labeled AI1 typically (Analog Input #1). You will also need to make sure to complete the PWM circuit using the GND terminal on the VFD.

Additional Information:
I have wired my 0-10V signal to the AI1 and GND terminals as suggested. I have also set the PD-01 and PD-02 settings to 1. Still nothing. Is there something else that I am missing?

Additional Information:
Thanks for the information. Can you let me know the model of the VFD that you have?

Additional Information:
VFD Model # YL600-2S-2K20

Additional Information:
Thanks. I will check our resources and documentation to see if there is another programming setting that needs to be changed.

Additional Information:
Does your VFD have a VI terminal?

Additional Information:
No, it does not. The terminals for this VFD are as follows (seperated by dashes "-").

10V-AI1-AO2-PLC-DI5-DI3-DI1-COM
AI2-GND-AO1-DI6-DI4-DI2-FM-24V

Additional Information:
Do you have a PD070 parameter?

PD070 is the main Analog Input parameter.

The options for that parameter is:
0: 0-10V
1: 0-5V
2: 0-20mA
3: 4-20mA
4: 0-10V (4-20mA Stacked)
5: XIA
6: (VI+XIA)/2
7: (3VA+XIA)/4
8: (XIA_XIB)/2
9: Max (XIA, XIB)
10: Min (XIA, XIB)


Additional Information:
There is a PD-00 thru PD-09. PD-07 is currently set to 0.

Additional Information:
It appears that the manual I’m using “Titled YL600” is not the same as your unit. I will check our manuals and find the one that has only PD-00 to PD-09.

Additional Information:
For that VFD, the parameters are P0. The 0 may look like a D on the display.

The parameters that need to be changed for the AI1 to work (Brackets [] around the correct selection):

P0-01: First Motor Control Mode
- 0: Sensorless Vector Control
- 1: Flux Vector Control (FVC)
- [2]: V/F Control

P0-02: Options of Command Source
- 0: Operation Panel Command Channel (LED will be off)
- [1]: Terminal Command Channel (LED will be on)
- 2: Communication Command Channel (LED will flicker)

P0-03: Options of Principle Frequency Source X
- 0: Digital Setting (Preset Frequency P0-08, UP/DOWN modifiable, no power-down memory)
- 1: Digital Setting (Preset Frequency P0-08, UP/DOWN modifiable, with power-down memory)
- [2]: AI1
- 3: AI2
- 4: AI3
- 5: Pulse Setting (DI5)
- 6: Multi Speed Instruction
- 7: Simple PLC
- 8: PID (Proportional Integral Derivative Control)
- 9: Communication Given

P0-11: Upper Limit Frequency Source
- 0: P0-12 (Make sure the P0-12 parameter has the correct max frequency if used)
- [1]: AI1
- 2: AI2
- 3: AI3
- 4: Pulse Setting
- 5: Communication Given

P0-27: Command Source Bundle with Frequency Sources
Single Digit: Options of Operation Panel Command Bundle with Frequency Sources
- 0: No Bundling
- 1: Digital Setting Frequency
- [2]: AI1
- 3: AI2
- 4: AI3
- 5: Pulse Setting (DI5)
- 6: Multi Speed Instruction
- 7: Simple PLC
- 8: PID
- 9: Communication Given
Double Digit: Options of Terminal Command Bundle with Frequency Sources
Hundred Place: Options of Communication Command Bundle with Frequency Sources
Kilobit: Options of Automatic Operation Bundle with Frequency Sources

P2-09: Upper Limit Source of Lower Torque Under Speed Control Mode
- 0: Function Code P2-10 Setting
- [1]: AI1
- 2: AI2
- 3: AI3
- 4: Pulse Setting
- 5: Communication Given
- 6: MIN (Al1, Al2)
- 7: MAX (Al1, Al2)
- Maximum range for options 1-7, accords with P2-10

If you elect to use a different AI#, then configure the parameters (P0-03, P0-11, P0-27 and P2-09) accordingly.

Click the link to add information to this solution:
I'VE BUFFERED A PWM SIGNAL TO 0-10V ANALOG AND I WOULD LIKE USE THAT RUN YOUR 110V 2.2KW SPINDLE VFD. COULD YOU PLEASE DETAIL THE CORRECT WIRING VFD SETTINGS GET WORKING?

All of our CNC machines can cut melamine. If your application (kitchen doors) requires large cutting area, then I would recommend the following machines:

- greenBull 4x (4'x8'), 5x (5'x10') or 6x (6'x 12')

- greenLean 4'x8' vertically oriented CNC machine

- Or our Fabricator Pro 4'x8' metal CNC machine

Click the link to add information to this solution:
CAN YOU RECOMMEND WHICH CNC MACHINE TO GO WITH FOR CUTTING MELAMINE AND MAKING KITCHEN DOORS FROM MDF. ALSO DO PROVIDE TRAINING ON OPERATING SETTING UP SHOP PRODUCTION USE? THANKS

We do have a relay board that words like a standard relay.

Here is the URL of the relay board that we offer:

https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

Click the link to add information to this solution:
I HAVE YOUR MACH3 USB BOB, DO YOU GUYS SELL A TORCH CONTROL RELAY CAN WIRE UP TO TURN MY PLASMA ON AND OFF HOW WOULD WIFE THAT TOO THIS BOB?

It is never too early to begin planning for the coming fall's influenza vaccination program. The most important thing you can do initially is to place your order for vaccine from your usual source. Some manufacturers often stop taking pre-orders in mid-May. Be sure to include vaccine for pediatric patients needing two doses and also for your facility's healthcare workers as part of your overall campaign.

Click the link to add information to this solution:
WE ARE ALWAYS CONCERNED THAT THERE WON'T BE ENOUGH VACCINE TO VACCINATE OUR PATIENTS IN THE FALL. WHAT CAN DO ASSURED WE'VE DONE ALL POSSIBLY AVOID THIS TYPE OF SITUATION?

Everyone always assumes they are doing something wrong when a plant fails to perform to their expectations. Grapes need pollinator activity to set viable fruit, but there is a shortage of bee activity throughout the country. When the flower cannot be pollinated by bees, the resulting fruit usually atrophies. It is not your fault, just a shortcoming in nature's network.

Click the link to add information to this solution:
I PLANTED SEVERAL CONCORD GRAPE VINES DURING THE PAST FEW YEARS. GOT A COUPLE OF VERY TINY BUDS THIS YEAR, BUT THEY DRIED UP AND DIED. WHAT AM DOING WRONG?

Hi. The HIWIN spec rail will fit standard M5 screws. If you are using non standard screws with wide heads, or pan heads that are a bit larger than a standard round heads, then it may not fit. Make sure to source screws that have standard round heads, or socket heads for fastening the 20mm HIWIN spec rails.

Click the link to add information to this solution:
I purchased some of your 20mm Hiwin Linear Rails. M5 bolts do not fit flush. The head stands out. Is the spec sheet out of date? What bolts will fit this rail AND T Nuts compatible with 8020's 15 series extrusions? Thanks.

Depending if the spindle can work with this specific VFD, it might be possible. However we would not like to risk you working unit, with a possible match so we would like more details on your specific model and any information available on the spindle itself.

Response
The only info on the spindle is 2.2KW 400HZ 220V. Made by Zhong Hua Jiang.

Was originally on a Delta C200 vfd. That is 220 single phase.

Click the link to add information to this solution:
I PURCHASED A VFD AND SPINDLE FROM FRIEND, HIS SET UP IS 220. DON'T HAVE 220 IN MY SHOP. QUESTION CAN USE YOUR 110 WITH THIS SPINDLE??