The leadscrew length for the greenBull long Z-axis is 47 inches.

Additional Information:

Click the link to add information to this solution:
BUILDING ONE OF YOUR GREENBULL 6X LONG AND 2.2 KILOWATT SPINDLE DOES NOT FIT. SEEMS LEAD SCREW YOU SENT WITH KIT IS SHORT 42" LOOKS LIKE IT NEEDS TO BE 5 OR 6 INCH LONGER. THIS CORRECT? WHAT THE NEEDED LENGTH FOR UNIT?

BYCNC Response:
Please send a photo of the bolts and assembly so we can determine the problem. Thanks.

User Response:
The holes on the Dremel holder are 0.442" and the bolt heads are 0.483". Picture will be sent. In the picture note that the left bolt has been ground down.

BYCNC Response:
You were sent incorrect fasteners due to a vendor change. We will be shipping the correct parts to you immediately, and thank you for letting us know about this mistake.

Click the link to add information to this solution:
I JUST RECEIVED MY WHITE ANT AND STARTED TO DO SOME BASIC ASSEMBLY. NOTICE THAT THE 1/4 X 20 BOLTS WITH PHILLIPS HEAD NOT FIT IN NOTCHES CUT FOR THEM - INSTANCE, ON DREMEL MOUNT. AM SUPPOSED BUY DIFFERENT HEADS, GRIND ALL DOWN, OR ROUTE OUT BIGGER NOTCHES. 3" BARELY Z-AXIS MOTOR

Sure, our blueChick and blackToe CNC Routers are considered relatively small machines at 1'x3' and 2'x4' respectively. They both use NEMA 23/24 motors. We recommend connecting the machines to either Mach3 or LinuxCNC and come with the necessary interface for either control software. You will need a computer for the control software and if you desire LinuxCNC, you will need a parallel port. Mach3 will accept either parallel port, or USB interface.

Click the link to add information to this solution:
I recently purchased the linksprite cnc engraving router and was wondering if your 3 axis small kit would be ok? the engraver came with nema 17 motors and a arduino board but but not liking the grbl control. could you point me in the right direction .Thanks.

The leadscrew length for the greenBull long Z-axis is 47 inches.

Additional Information:

Click the link to add information to this solution:
Building one of your greenBull 6X Long and 2.2 kilowatt spindle does not fit. Seems lead screw you sent with kit is short 42" looks like it needs to be 5 or 6 inch longer. Is this correct? What is the needed length of lead screw for this unit?

Here is how to connect your router to the parallel breakout board through the on-board relay. You will need a spare extension cord. You will need to remove a portion of the outer jacket of the extension cord to expose the white, black and green wires (white = neutral, black = live and green = ground), understanding that the neutral and live create the completed circuit.

See this image of a similar connection. The terminal has the same connections.
https://www.buildyourcnc.com/images/vacuum-pressure-controller-relay-terminals-700.JPG

Image of the relay terminal:
https://www.buildyourcnc.com/images/breakoutboardrelayNONC.PNG

The live/black wire would be cut and one end of the cut would be secured into the P terminal and the other cut end would be secured into the S terminal. The live and ground wire would be uncut and travel from the plug to the router.


Additional Information:
You can also connect other high powered devices to the breakout board using any of the output terminals. You will need to supply extra relays like the one shown here:
https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

Or you can find SSRs (Solid State Relays) that will accept 5v to drive the relay coil. Make sure the SSR will protect the 5V line from Back EMF as there is a coil in the relay. The one we sell contains a fly-back diode to protect the 5v terminal.

Click the link to add information to this solution:
I have your breakout board with relay parallel port , I have a vacuum, light on router and air pump I want to also hook up to board, can I hook those up to board and also could I had reylays to each one, what is the best way to figure this out any information would be great. Thanks

We recommend our electronics combo for the scratch build kit, which you can find on our site here: https://buildyourcnc.com/item/electronicsAndMotors-3axis-425-elcombo. This is our standard general purpose 3 axis electronics system, and includes (3) NEMA 24 425 oz-in stepping motors, (3) Drivers (3.0Amp 24-40 Volts, with 1-1/64 microstepping), (1) 36v 8.8a Power Supply, (1) Interface Board either USB or Parallel. (The USB version requires PlanetCNC software; the parallel interface board gives you a variety of options, Mach3 being one popular choice.)

Click the link to add information to this solution:
I got the plans and hardware from you guys and im almost ready for the stepper motor part of this build. what size motors are good to use for this build? the size of cnc will be 2x4 when finish or what size will not work? thanks

Looks like you are trying to screw me out of $30 plus tax as there will be no pdf files forthcoming unless I shell out another $255. Unless you provide the pdf files I will be forced to seek return of funds and will be notifying VISA, GOOGLE PLAY and the BBB doing so until I get satisfaction. If you are not going to honor your book title by providing complete usable information you should remove your book from the market place, or offer it for free. At this point I don't know how you justify screwing your customers like this, but this one ain't going to take it laying down.

Additional Information:
Official Buildyourcnc response:
Thanks for informing us of this issue. Have you looked at this part of the wabsite:
https://www.buildyourcnc.com/Book.aspx

The link to the "book" portion of the website is in the footer of every page of the website. If there is a problem with the pdf documents on any page of this portion of the website, please let me know here. Many thanks, Patrick Hood-Daniel

Click the link to add information to this solution:
I PURCHASED YOUR BOOK TO BUILD A CNC ROUTER, THE PLAN DRAWINGS ARE INDECIPHERABLE AND TEXT WITH THEM IS ILLEGIBLE. THERE NOTE REFER MDF PARTS LAYOUT 1 PDF, 2 PDF PLANS & CUT LIST DOWNLOADABLE FROM THIS SITE. WHERE THEY CAN'T FIND THEM?

Yes, here is the URL for the parallel breakout board that we sell:

https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Click the link to add information to this solution:
can I purchase just the parallel controller board? I purchased the usb option 4 axis combo and would like to also try the system with my parallel port computer. Any help with this will be greatly appreciated; my goal is to implement mach4.

We sell our ACME screws in total length (overall length you require), but if individual lengths are needed you can contact us via phone (281-815-7701) or email (customerservice@buildyourcnc.com).

A $2.00 order will be a total of 1 inch, but if ordered separately then you will receive 2 of the same length.

Click the link to add information to this solution:
For the 1/2'' 5 start ACME leadscrew, what is the length purchased for the $2.00 order? and if you make 2 orders, are you getting two separate rods or 1 rod at twice the length. Thanks.

BYCNC Response:
Please send a photo of the bolts and assembly so we can determine the problem. Thanks.

User Response:
The holes on the Dremel holder are 0.442" and the bolt heads are 0.483". Picture will be sent. In the picture note that the left bolt has been ground down.

BYCNC Response:
You were sent incorrect fasteners due to a vendor change. We will be shipping the correct parts to you immediately, and thank you for letting us know about this mistake.

Click the link to add information to this solution:
I just received my White Ant and started to do some basic assembly. I notice that the 1/4 x 20 bolts with Phillips head do not fit in the notches cut for them - for instance, on the Dremel mount. Am I supposed to buy bolts with different heads, grind them all down, or route out bigger notches. The 3" bolts barely fit in the Z-axis motor mount.

Make sure all your bolts/screws are tighten correctly and if using a lead screw make sure your anti-backlash nut is not offset. Now a default setting will be 10101100 for your driver dip switch settings and in motor tuning (mach3) 1600 steps per, 400.02 velocity, 4 in acceleration. now the acceleration and velocity can be adjusted to move your machine faster, but if set to high they could stall. Make sure you have the correct wiring from your motor to your driver (https://www.buildyourcnc.com/Documents/PN.SM60HT86-2008BF-U%20(inhouse%20PN.60BYGH303-13)%20(1).pdf).

Click the link to add information to this solution:
I have your Nema 24 electronics kit and am having problems with the Z axis dropping over time. I am using a PC 8902 motor. Any ideas on what the problem is? What should be the motor tuning values in Mach3? Thanks

John Parent,

We are currently waiting for rails to come in as they are out of stock. We appreciate your patience. Please email customerservice@buildyourcnc.com and let us know if there is anything we can do.

Click the link to add information to this solution:
hi, i ordered a bunch of stuff from you, the payment went through, it's been 3 weeks, any word on shipping date, I ordered 6 linear rails with block and some sprockets

There is some variation in the outward appearance of laser power supplies due to sourcing through different vendors. However, the basic wiring requirements are the same in each case. For the unit with integrated laser controller, follow the diagram found here: https://buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx#prettyPhoto/0/. The terminals on the signal side will have a 6 connection terminal block -- these are the ones labeled 5V, IN, G, P (or WP), L (or TTL-L), and H (or TTL-H). The High Power side will have 3 inputs for AC power, one high voltage lead, and one return line. Connect these as shown in the diagram as well: the return line goes on the "front" (beam exit end) terminal of the laser tube, the high voltage lead goes to the "back" terminal of the tube, the FG terminal (or G) receives the earth ground wire of the AC power cable, and the two AC terminals receive the line and neutral wires of the AC power cable (it doesn't matter in this case which wire goes to which terminal).

Click the link to add information to this solution:
I purchased the blackTooth Laser Engraver with integrated Laser Control Unit and have been following your instructions. I noticed that the laser tube power supply is different that what is shown in your instructions. Do you have any better wiring guides that I can follow for the version that I received?

I would not recommend slaving an axis using the method of taking an additional axis from the USB interface. Instead, wire both drivers to a single axis on the USB interface. This will insure perfect signal output to both drivers. If you requre the motors to spin in opposite directions, simply wire one of the motors to the driver reversing the coil A and B connections, or use a hex inverter (https://www.buildyourcnc.com/tutorials/Tutorial-Two-Motors-Spinning-Oppositely-On-Single-Axis).

Click the link to add information to this solution:
I purchased a USB Breakout board, motors and drivers, paid for CNC USB Controller Software and I CAN NOT "Slave" an axis, but there is an option to do that. The moment I connect USB Breakout Board "Slave" option becomes shaded and I can no longer select it (becomes not functional). What is going on? Need help asap. Thanks

The Mach3 USB will not work with Linux CNC. You can use our parallel breakout baord instead (if you have a computer that has a parallel port available).

Here is the link to that interface:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Click the link to add information to this solution:
Hello. I'm currently building my first CNC router, and I'm powering it with a 3 axis electronics kit that was purchased through your site. I chose to get the Mach 3 USB Breakout board, but now I'm wanting to try to use Linux CNC to work with the computer I have available. Will that work with this board?

The 5x10 greenBull base kit comes with the structure, hardware, and electronics for motion control. In order to have a fully functional CNC you will need a table base for your machine, a spindle or router to handle your cutting applications, end mills (bits) for cutting, CAD, CAM and CNC software, and a computer. There are also accessories you can add such as limit switches, emergency stops, and cable carrier for cable management. If you are looking for more information or a formal quote please contact sales@buildyoucnc.com

Click the link to add information to this solution:
I'm not sure of ALL the things I will need to do some of my ideas for the cnc machine. I'll mostly be cutting out 3/4" plywood projects. How much minimum for a 5' by 10' system? I need the hardware and software to get the job done. I saw the price for your basic unit 3-4 grand but don't know what all I NEED to start work.

The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.

Click the link to add information to this solution:
I bought a 'BuildyourCNC V1' relay board to go with my mach3 usb controller. I have been sent a 'Songle' relay. It's not the one in your picture and it's got different connections, for which there isn't a wiring diagram. The one I ordered says it is 5v, this one seems to be saying it's a 24v unit. Can you please explain what has happened? Thanks

The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.

Click the link to add information to this solution:
I bought a 'BuildyourCNC V1' relay board to go with my mach3 usb controller. I have been sent a 'Songle' relay. It's not the one in your picture and it's got different connections, for which there isn't a wiring diagram. The one I ordered says it is 5v, this one seems to be saying it's a 24v unit. Can you please explain what has happened? Thanks

Looks like you are trying to screw me out of $30 plus tax as there will be no pdf files forthcoming unless I shell out another $255. Unless you provide the pdf files I will be forced to seek return of funds and will be notifying VISA, GOOGLE PLAY and the BBB doing so until I get satisfaction. If you are not going to honor your book title by providing complete usable information you should remove your book from the market place, or offer it for free. At this point I don't know how you justify screwing your customers like this, but this one ain't going to take it laying down.

Additional Information:
Official Buildyourcnc response:
Thanks for informing us of this issue. Have you looked at this part of the wabsite:
https://www.buildyourcnc.com/Book.aspx

The link to the "book" portion of the website is in the footer of every page of the website. If there is a problem with the pdf documents on any page of this portion of the website, please let me know here. Many thanks, Patrick Hood-Daniel

Click the link to add information to this solution:
I purchased your book to build a cnc router, the plan drawings are indecipherable and text with them is illegible. There is a note to refer to MDF Parts Layout 1 PDF, MDF Parts Layout 2 PDF and MDF Plans & Cut List PDF downloadable from this site. Where are they I can't find them?