The total length of the brush strip for a 2.2kW spindle would be 17 1/4" inches.

Additional Information:
20

Click the link to add information to this solution:
LENGTH OF THE BRUSH STRIP FOR SPINDLE 2.2KW

The roller chain lengths for the greenBull 4x is:
- 13 feet for each side of the X axis (total of 26 feet), and
- 6 feet for the Y-axis

Click the link to add information to this solution:
ROLLER CHAIN LENGTH GREENBULL

The total cable length for a greenBull 5x is 50 ft. Now the individual cable lengths for the axis, is x=15 ft, y=17 ft, z=18 ft.

Click the link to add information to this solution:
GREENBULL 5X CABLE LENGTH

The total length for the 890 router strip brush is 18.5" inches.

Additional Information:
20

Click the link to add information to this solution:
Strip BRUSH FOR 890 ROUTER

Specifically for a blackToe/blackFoot the total length for a 7518 router brush strip is 19 1/2" inches.

Click the link to add information to this solution:
BRUSH STRIP 7518 ROUTER

If your axis shutters and will not move unless moved by another force, that sounds like your acceleration is set too high. Lower the acceleration until it works well, then lower it a bit more to have a margin of safety.

Users response:
I've lowered my acceleration to 1 in the StepCon program and it still shutters when I jog it, anything else I could check?

Buildyourcnc response:
IF that didn't work, try swapping the X and Y drivers. That way you will pinpoint if the issue is the driver. If the proplem persists, then there may be an issue with the motor itself.

Buildyourcnc response:
The X and Y drivers can be easily swapped by swapping only the motor wires.

- Remove the x-axis motor wires from the X driver.
- Remove the Y motor wires from the Y driver.
- Insert the X motor wires into the Y driver.
- Insert the Y motor wires into the X driver.

Buildyourcnc response:
Now the Y-axis will move the gantry. Test the Gantry movement by moving the Y axis using the up and down arrow keys (mach3).

Users response:
Problem is now solved, I switched the X and Y at the redFly and got the same problem, so then I undid the wires going to each motor and switched them there and it I had a bad solder point in the X axis connector, thank you for the help

Buildyourcnc response:
You're very welcome. We will make sure to thoroughly check the solder points on the cable connectors prior to a redFly delivery.

Click the link to add information to this solution:
GREENBULL 5X10 X AXIS SHUTTERS

The greenBull 6X, uses a total of 52 Ft, of silicon tubing 1/4" ID - 3/8" OD. One way uses 26 Ft.

Click the link to add information to this solution:
GREENBULL 6X SILICON TUBING

The roller chain lengths for the greenBull 4x is:
- 13 feet for each side of the X axis (total of 26 feet), and
- 6 feet for the Y-axis

Click the link to add information to this solution:
ROLLER CHAIN LENGTHS FOR GREENBULL 4X

Actual table dimension: 4'x8' is 56.078"x 121.50" (the overhang in the illustrations should be 3/4" thick)
To determine the frame dimensions, first consider using the frame height shown of almost 3' (2.86'). The width of the frame should be 4" narrower than the dimension from rail edge to rail edge (6X rail to rail is 80.078"). This will provide a 2" overhang on both sides (4X frame width should be 56.078").
The length of the frame should be 4" shorter than the desired length of the rails to provide a 2" overhang on both ends. The travel length will be 20" shorter than the rail length due to the space occupied by the gantry sides.
Two long pieces of 3/4" material will need to be placed on top of the frame with the 2" overhang on the sides and the end. These long strips of material will receive the rails and the chain mounts on the ends.


Link:
https://www.buildyourcnc.com/Item/cnc-machine-greenBull-v4-4X

Click the link to add information to this solution:
GREENBULL TABLE

The total cable length for a greenBull 6x is 65 ft. Now the individual cable lengths for the axis, is x=20 ft, y=22 ft, z=23 ft.

Click the link to add information to this solution:
GREENBULL CABLE

The files and hardware option for our machines has been removed from the site due to the following reasons:
Difficulty for the end use of the files and the challenges (and time/money) on our side to assist in using these files.
The abuse of these files over the internet.
Ultimately may reduce the sales of machines keeping us in business.
Sadly, this is what has come out of our company attempting to be open; however, the machines sold on this site is still far lower in price than the competition for the quality that we provide as we have a great desire to engender the cottage industry to fulfill their need for low end manufacturing. My sincere apologies if this causes any inconvenience.

Additional Information:
NO, is not possible, I can help with the shipping cost

Additional Information:

Click the link to add information to this solution:
PLANS GREENBULL

Actual table dimension: 4'x8' is 56.078"x 121.50" (the overhang in the illustrations should be 3/4" thick)
To determine the frame dimensions, first consider using the frame height shown of almost 3' (2.86'). The width of the frame should be 4" narrower than the dimension from rail edge to rail edge (6X rail to rail is 80.078"). This will provide a 2" overhang on both sides (4X frame width should be 56.078").
The length of the frame should be 4" shorter than the desired length of the rails to provide a 2" overhang on both ends. The travel length will be 20" shorter than the rail length due to the space occupied by the gantry sides.
Two long pieces of 3/4" material will need to be placed on top of the frame with the 2" overhang on the sides and the end. These long strips of material will receive the rails and the chain mounts on the ends.


Link:
https://www.buildyourcnc.com/Item/cnc-machine-greenBull-v4-4X

Click the link to add information to this solution:
WHAT ARE THE DIMENSIONS FOR GREENBULL TABLE?

If you use the 2.2kW spindle, it can cut at 3/4 inch or 19 mm deep with at least a 1/4" cutting diameter single flute end mill. You will get better results with larger diameter end mills, but that is the worst case scenario. I still recommend doing a finishing pass on the edge to make sure everything is perfect.

Click the link to add information to this solution:
CAN THE GREENBULL CUT 18MM BIRCH IN ONE PASS?

76" X 40" X 26"
230 LBS

Click the link to add information to this solution:
WHAT ARE THE SHIPPING DIMENSIONS FOR GREENBULL?

The roller chain lengths for the greenBull 4x is:
- 13 feet for each side of the X axis (total of 26 feet), and
- 6 feet for the Y-axis

Click the link to add information to this solution:
WHAT ARE THE ROLLER CHAIN LENGTHS FOR GREENBULL 4X

The greenBull can range is routing width sizes of 5 feet and 6 feet. The blackFoot has a 4 foot routing width.

Previous Solution:
The greenBull machine has a sturdier gantry than the blackFoot, so you can be more agressive with the cutting feedrate (cutting speed). The blackFoot is also a good machine, but it all comes down to the speed at which you want to produce the fabrication

The spindle is also highly recommended for it's quietness and easier cleanup (no fan blowing the dust in the air)

Additional Information:



Additional Information:

Click the link to add information to this solution:
WHICH MACHINE SHOULD I BUY, GREENBULL OR BLACKFOOT?

The greenBull can range is routing width sizes of 5 feet and 6 feet. The blackFoot has a 4 foot routing width.

Previous Solution:
The greenBull machine has a sturdier gantry than the blackFoot, so you can be more agressive with the cutting feedrate (cutting speed). The blackFoot is also a good machine, but it all comes down to the speed at which you want to produce the fabrication

The spindle is also highly recommended for it's quietness and easier cleanup (no fan blowing the dust in the air)

Additional Information:



Additional Information:

Click the link to add information to this solution:
WHICH MACHINE SHOULD I BUY, THE GREENBULL OR BLACKFOOT?

The greenBull can range is routing width sizes of 5 feet and 6 feet. The blackFoot has a 4 foot routing width.

Previous Solution:
The greenBull machine has a sturdier gantry than the blackFoot, so you can be more agressive with the cutting feedrate (cutting speed). The blackFoot is also a good machine, but it all comes down to the speed at which you want to produce the fabrication

The spindle is also highly recommended for it's quietness and easier cleanup (no fan blowing the dust in the air)

Additional Information:



Additional Information:

Click the link to add information to this solution:
SHOULD I SELECT THE GREENBULL OR BLACKFOOT CNC MACHINE?

The Greenbull machine can cut a very wide variety of materials ranging from foam to aluminum. We recommend the use of our 2.2kW spindle to allow the greatest flexibility. Aside from that, the most important thing is to use an appropriate end mill for the material you are cutting and to use appropriate speeds and feed rates.



BYCNC Response:
Our 40W laser can cut up to about 1/4" materials ranging from wood and acrylic down through lighter materials such as leather, fabric, foam, etc. Speed and final cut are greatly enhanced by an air assist upgrade. We also offer an 80W laser which has approximately twice the capabilities of the 40W.

Additional Information:

Click the link to add information to this solution:
WHAT MATERIALS CAN THE GREENBULL MACHINE CUT? LASER ETCH?