[ Log In ]
[ Register ]

Question #: 1083

Question: GREENBULL 5X CABLE LENGTH

Current Solution

The total cable length for a greenBull 5x is 50 ft. Now the individual cable lengths for the axis, is x=15 ft, y=17 ft, z=18 ft.

Respond:

Other Possible Solutions to this Question

  • GREENBULL BRUSH STRIP LENGTH

    The brush strip for a 7518 router specifically for a GreenBull is 18 3/4" inches in length.

    Click the link to respond:
    GREENBULL BRUSH STRIP LENGTH

  • GREENBULL CABLE

    The total cable length for a greenBull 6x is 65 ft. Now the individual cable lengths for the axis, is x=20 ft, y=22 ft, z=23 ft.

    Click the link to respond:
    GREENBULL CABLE

  • What will be the amount of cable carrier that I will need for a greenBull 5x?

    To determine the length of cable carrier you will need for a single axis, measure the axis travel of your machine, divide this by 2 and add 12 inches. The radius of the curl is 2 inches.
    The amount of cable carrier needed for the CNC machines that we provide will be:

    blueChick: Total 4 Ft

    blackToe: Total 5 Ft

    blackFoot: Total 8 Ft

    greenLean: Total 8 Ft

    greenBull 5x: Total 10 Ft

    greenBull 6x: Total 11 Ft

    Click the link to respond:
    What will be the amount of cable carrier that I will need for a greenBull 5x?

  • BLACKTOE MOTOR CABLE LENGTH

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to respond:
    BLACKTOE MOTOR CABLE LENGTH

  • BLACKTOE MOTOR CABLE LENGTH

    The total length of cable for the greenBull 5x is 50 ft.
    Now the individual lengths for all three axis, is x=15 ft, y=17 ft, z=18 ft.

    Click the link to respond:
    BLACKTOE MOTOR CABLE LENGTH

  • GREENBULL 5X10 X AXIS SHUTTERS

    If your axis shutters and will not move unless moved by another force, that sounds like your acceleration is set too high. Lower the acceleration until it works well, then lower it a bit more to have a margin of safety.

    Users response:
    I've lowered my acceleration to 1 in the StepCon program and it still shutters when I jog it, anything else I could check?

    Buildyourcnc response:
    IF that didn't work, try swapping the X and Y drivers. That way you will pinpoint if the issue is the driver. If the proplem persists, then there may be an issue with the motor itself.

    Buildyourcnc response:
    The X and Y drivers can be easily swapped by swapping only the motor wires.

    - Remove the x-axis motor wires from the X driver.
    - Remove the Y motor wires from the Y driver.
    - Insert the X motor wires into the Y driver.
    - Insert the Y motor wires into the X driver.

    Buildyourcnc response:
    Now the Y-axis will move the gantry. Test the Gantry movement by moving the Y axis using the up and down arrow keys (mach3).

    Users response:
    Problem is now solved, I switched the X and Y at the redFly and got the same problem, so then I undid the wires going to each motor and switched them there and it I had a bad solder point in the X axis connector, thank you for the help

    Buildyourcnc response:
    You're very welcome. We will make sure to thoroughly check the solder points on the cable connectors prior to a redFly delivery.

    Click the link to respond:
    GREENBULL 5X10 X AXIS SHUTTERS

  • CABLE LENGTHS FOR THE BLACKFOOT

    The blackfoot requires a total of 50 feet of cable.

    The X axis needs 15 feet
    The Y axis needs 17 feet
    and the Z-axis needs 18 feet

    These are 20 gauge 4 conductor cable.

    Click the link to respond:
    CABLE LENGTHS FOR THE BLACKFOOT

  • MOTOR CABLE LENGTH FOR BLUECHICK

    The recommended total length of motor cable should be 15 feet for the blueChick v4.2

    Z - 6 feet
    Y - 5 feet
    X- 4 feet

    20 AWG 4 conductor

    If your drivers will be positioned farther from the machine, you may need longer cable.

    Click the link to respond:
    MOTOR CABLE LENGTH FOR BLUECHICK

  • WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to respond:
    WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

  • WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to respond:
    WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

  • WHAT CABLE LENGTHS ARE USED FOR THE BLACKTOE

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to respond:
    WHAT CABLE LENGTHS ARE USED FOR THE BLACKTOE

  • WHAT CABLE LENGTHS SHOULD USE FOR THE BLACKTOE

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to respond:
    WHAT CABLE LENGTHS SHOULD USE FOR THE BLACKTOE

  • WHAT LENGTH OF CABLE DO I NEED FOR A BLAKCFOOT

    The blackfoot requires a total of 50 feet of cable.

    The X axis needs 15 feet
    The Y axis needs 17 feet
    and the Z-axis needs 18 feet

    These are 20 gauge 4 conductor cable.

    Click the link to respond:
    WHAT LENGTH OF CABLE DO I NEED FOR A BLAKCFOOT

  • What are the overall dimensions for a greenbull 5x10

    The overall size (Foot Print(Roughly)) is:
    W: 90" x L: 142.5" x H: 35"

    Height:
    Is from table top to highest point and not from the floor to highest point.(H for the 5X/6X can vary in size due to the height of the table/frame, since it can be adjusted to the specific needs of the customer)).

    Additional Information:

    Click the link to respond:
    What are the overall dimensions for a greenbull 5x10

  • WHAT CABLE LENGTHS SHOULD USE FOR THE BLACKFOOT CNC MACHINE

    The blackfoot requires a total of 50 feet of cable.

    The X axis needs 15 feet
    The Y axis needs 17 feet
    and the Z-axis needs 18 feet

    These are 20 gauge 4 conductor cable.

    Click the link to respond:
    WHAT CABLE LENGTHS SHOULD USE FOR THE BLACKFOOT CNC MACHINE

  • GREENBULL 6X SILICON TUBING

    The greenBull 6X, uses a total of 52 Ft, of silicon tubing 1/4" ID - 3/8" OD. One way uses 26 Ft.

    Click the link to respond:
    GREENBULL 6X SILICON TUBING

  • buy greenbull in europe

    The greenBull can be purchased internationally from the buildyourcnc.com site. We will ship to any country that is serviced by FedEX, UPS or USPS.

    Click the link to respond:
    buy greenbull in europe

  • WHAT LENGTH OF MOTOR CABLE SHOULD BE USED WTIH THE BLUECHICK V4.2

    The recommended total length of motor cable should be 15 feet for the blueChick v4.2

    Z - 6 feet
    Y - 5 feet
    X- 4 feet

    20 AWG 4 conductor

    If your drivers will be positioned farther from the machine, you may need longer cable.

    Click the link to respond:
    WHAT LENGTH OF MOTOR CABLE SHOULD BE USED WTIH THE BLUECHICK V4.2

  • How is the greenBull 4x shipped?

    The shipping weight (with crate) of the greenBull 4X CNC machine with the dual laser/spindle head is 230 lbs. The overall dimensions are: 76"x36"x27". The crate is typicall send via freight.

    Click the link to respond:
    How is the greenBull 4x shipped?

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.