The strip brush is .2 inches (5.23 mm) wide, so a slot of that width or slightly wider will work. We use a .25 inch groove and use glue to adhere the strip brushes in our dust shoe.

The material of the bristles and the strip that holds the bristles are nylon.

Click the link to add information to this solution:
What are the specifications for the 2" strip brush as far as dimensions and width of the rubber top?

The strip brush overall height is 2 inches, of which 3/16 inch is backing. The strip is 1/4 inch wide. The diameter of the bristles is 0.01 inch.

Click the link to add information to this solution:
for 2" Strip Brush per inch what is the dimensions (Width, High and thickness)

Inside Diameter: 1/2" (actual dimension 0.4975 inches or 12.63 mm)

- Outside Diameter: 1.122 inches or 28.4988 mm

- Thickness: .31 inches or 7.89 mm

Thank you for this question as it caused me to update the description:
https://www.buildyourcnc.com/item/bearing-!5-standardbearing

Click the link to add information to this solution:
What are the other two dimensions of the 1/2" ID bearings used to support lead screws?

The overall dimensions of our 2.5 modular stepper divers is:

L: 1.875"/ 47.625mm
W: 1.433"/ 36.3982mm
H: .585"/ 14.859mm (height might change due to different terminal block height (other we have on hand is .464"/ 11.7856mm))

Currently we do not have a CAD model on hand.

Click the link to add information to this solution:
What are the overall dimensions of the 2.5A small stepper drivers? Is there a CAD model available?

The overall dimensions of the machine when mounted to a wall will be 119" from side to side and 25-1/2" inches out (from the wall to the longest part which is the bottom). Height of the machine (clearance) is about 76" maximum.

Click the link to add information to this solution:
What are the dimensions of the VLXL cabinet? With space saving lauded as a feature, a critical bit of information.

The dimensions for our USB breakout board are:

L: 2.745"/ 69.723mm
W: 2.244"/ 56.9976mm
H: .501"/ 12.7254mm

Currently we do not have a CAD model on hand.

Click the link to add information to this solution:
What are the overall dimensions of the USB interface board? Is there a CAD model available?

The specifications for our 3/8" bearings are R6ZZ. The ZZ means double metal shielded. The metal shielding is to protect the ball bearings between the inner race and outer race.

Inside diameter: 3/8"
Outside Diameter: 7/8"
Width: 9/32"

Click the link to add information to this solution:
what are the dimensions and model number of the 3/8" ID roller bearings on your website?

The mounting hole dimension for the 1/2" 10 TPI 5 starts antibacklash nut is 1.13" or 28.7 mm. I added a drawing to the antibacklash nut product webpage so you can see other dimensions.

Antibacklash nut product webpage: https://www.buildyourcnc.com/item/mechanical-leadscrews-antibacklash-nut-!5-5-starts-10-tpi

Thanks

Additional Information:
You can also see the drawing directly here: https://www.buildyourcnc.com/images/Antibacklash_nut_1_2_drawing-800.JPG

Click the link to add information to this solution:
What are the mounting hole dimensions of the 1/2" Anti-Backlash Lead Nut

The actual cutting dimensions for our blackToe machine is 2'(24") x 4'(48"), the overall size of the structure built is a bit larger so that our customers have the actual size mentioned with each of our machines!

Click the link to add information to this solution:
blackToe 2'x4' CNC Router - What are the actual x and y cutting dimensions (eg: 22"x46")

Our SBR20 rails use M8 bolts and are suitable for use with 8020 aluminum or any other common machine material. We suggest the use of our ball bearing pillow blocks with these rails, which you can find on our website here: https://buildyourcnc.com/item/mechanical-rails-linear-ball-bearing-block

Additional Information:
HOW TO FIND WIDH 38 HEIGHT 26 LINER GUIDE RAIL

Click the link to add information to this solution:
What are the bolt dimensions for the SBR20 linear rails, can they work with 8020 Aluminum extrusions?

Our SBR20 rails use M8 bolts and are suitable for use with 8020 aluminum or any other common machine material. We suggest the use of our ball bearing pillow blocks with these rails, which you can find on our website here: https://buildyourcnc.com/item/mechanical-rails-linear-ball-bearing-block

Additional Information:
HOW TO FIND WIDH 38 HEIGHT 26 LINER GUIDE RAIL

Click the link to add information to this solution:
What are the hole spacing dimensions for the Linear Guide Rail 20mm? I'm trying to figure out what size aluminum extrusion to purchase so I can mount these to it.

The dimensions for our power supplies will be the same.

Dimensions:
L: 8.5" / 215.9mm
W: 4.5" / 114.3mm
H: 2" / 50.8mm

Click the link to add information to this solution:
What are the dimensions of the 24v 8.3A power supply?

I would recommend using the blackToe CNC machine kit. The overall travel dimensions are 24" x 48" x 6". This will provide a bit of space on the sides as wiggle room if your guitar bodies are at the extremes of the 12". Also, if you are manufacturing may of these, the larger routing area, the more guitar bodies you will be able to cut at one time.

Click the link to add information to this solution:
I need a machine to cut guitar bodies. The bodies are 12" x 16" and 1.5" thick. What would work best?

Actual table dimension: 4'x8' is 56.078"x 121.50" (the overhang in the illustrations should be 3/4" thick)
To determine the frame dimensions, first consider using the frame height shown of almost 3' (2.86'). The width of the frame should be 4" narrower than the dimension from rail edge to rail edge (6X rail to rail is 80.078"). This will provide a 2" overhang on both sides (4X frame width should be 56.078").
The length of the frame should be 4" shorter than the desired length of the rails to provide a 2" overhang on both ends. The travel length will be 20" shorter than the rail length due to the space occupied by the gantry sides.
Two long pieces of 3/4" material will need to be placed on top of the frame with the 2" overhang on the sides and the end. These long strips of material will receive the rails and the chain mounts on the ends.


Link:
https://www.buildyourcnc.com/Item/cnc-machine-greenBull-v4-4X

Click the link to add information to this solution:
What are the table dimensions for the greenBull so I can build it.

The dimensions of the optional table are 73" x 34".

Click the link to add information to this solution:
What are the dimensions for a black toe torsion box? The machine dimensions are https://www.buildyourcnc.com/FAQ/1178 but I do not know the required overhang. I assume the overhang needs to be 3/4 inch ...

No they will not come in that length as a default, we would contact the buyer to ask specific lengths due to the total length purchased.

However if you order the 1/2" lead screw we can get them cut to the specific length you require, by contacting us here or call us at 281-815-7701.

Click the link to add information to this solution:
If I order 19ft of the 1/2" lead screw will it come in three 6'5" lengths by default? This is what I need. Thanks

The required motors are the 425 oz-in stepping motors, would be the required motors to run the machine efficiently.

Click the link to add information to this solution:
What steppers are required for the X, Y, and Z axis of the scratch build kit? Do they all need to be the same rating?

If you would like to add a laser to a plasma table, you will need the following parts:

Laser tube at 40 watts:
https://www.buildyourcnc.com/item/Laser-Component-Laser-Tube-CO2-40Watt

Mirror mounts (this will depend on the way you mount the laser tube):
https://www.buildyourcnc.com/item/Laser-Component-Mirror-Mount-20mm

Mirrors for the mirror mounts:
https://www.buildyourcnc.com/Item/Laser-component-20mm-mirror-25mm

Laser Tube Power Supply:
https://www.buildyourcnc.com/item/Laser-Component-Power-Supply-CO2-40W

Laser Focus Lens:
https://www.buildyourcnc.com/item/laser-component-20mm-lens-2-inch-50!80mm

Mirror and Lens Mount and Nozzle:
https://www.buildyourcnc.com/item/Laser-Component-Nozzle-20mm-lens-mirror

High Tension Extension Cable:
https://www.buildyourcnc.com/item/Laser-component-Power-Supply-High-Tension-extension-wire

Laser Control System:
https://www.buildyourcnc.com/item/Laser-Component-Laser-Control-System

Screw Posts (to connect the high tension and return wire to the laser tube, highly recommended as the leads on the laser tube are fragile):
https://www.buildyourcnc.com/item/laser-component-newbiehack-connectors-screw-terminal-binding-post

Safety Eyewear for CO2 laser wavelength:
https://www.buildyourcnc.com/item/laser-components-goggles-safety-tinted

Click the link to add information to this solution:
I have an Eagle Plasma table and I want to add a 40 laser. Can you supply me a list of what I need to make this happen.

Shipping crate size 121" X 36" X 92"

Weight 511 LBS

Click the link to add information to this solution:
WHAT ARE THE SHIPPING DIMENSIONS FOR VERTICAL LASER